Submitted by Automa??o e Estat?stica (sst@bczm.ufrn.br) on 2016-08-16T20:12:23Z
No. of bitstreams: 1
EdsonSilvaDoNascimento_DISSERT.pdf: 2737774 bytes, checksum: 77ef6f8833e63d26e699ee6f42209b93 (MD5) / Approved for entry into archive by Arlan Eloi Leite Silva (eloihistoriador@yahoo.com.br) on 2016-08-17T21:43:01Z (GMT) No. of bitstreams: 1
EdsonSilvaDoNascimento_DISSERT.pdf: 2737774 bytes, checksum: 77ef6f8833e63d26e699ee6f42209b93 (MD5) / Made available in DSpace on 2016-08-17T21:43:01Z (GMT). No. of bitstreams: 1
EdsonSilvaDoNascimento_DISSERT.pdf: 2737774 bytes, checksum: 77ef6f8833e63d26e699ee6f42209b93 (MD5)
Previous issue date: 2016-04-08 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior (CAPES) / Este trabalho tem como objetivo encontrar um material alternativo para os atuais capacitores de t?ntalo usados na ind?stria. O ni?bio ? um substituto em potencial por ser mais leve e barato que o t?ntalo. Eles pertencem ao mesmo grupo da tabela peri?dica e, desta forma, apresentam v?rias propriedades f?sicas e qu?micas semelhantes. O ni?bio ? usado em diversas aplica??es tecnologicamente importantes, e o Brasil possui as maiores reservas mundiais, em torno de 96%. Esses capacitores eletrol?ticos possuem alta capacit?ncia especifica, ou seja, podem armazenar altas energias em volumes pequenos comparados a outros tipos de capacitores. A rota de produ??o do capacitor de ni?bio foi realizada atrav?s das etapas de processamento da metalurgia do p?. Inicialmente, o p? de ni?bio foi caracterizado atrav?s de DRX, MEV, granulometria a laser; e depois peneirado para apresentar uma granulometria de 400mesh. Posteriormente o p? foi compactado com uma matriz especial e ent?o sinterizado em diferentes temperaturas e tempos de isoterma. Ap?s a sinteriza??o as amostras passaram por processo de oxida??o an?dica em diferentes tens?es para a obten??o de uma camada ?xida, a qual desempenha o papel do diel?trico do capacitor. Os resultados foram obtidos atrav?s de uma ponte de capacit?ncia, mostrando a forte influ?ncia da sinteriza??o e do processo de oxida??o an?dica na produ??o dos capacitores. Os melhores resultados foram obtidos para o p? sinterizado a 1400?C durante 60 minutos e anodizados a uma tens?o de 10V. O processo apresentou valores significativos e com mais estudos pode-se melhorar ainda mais esses valores para competirem com o t?ntalo. / It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential replacement for be lighter and cheaper than tantalum. They belong to the same table group periodically and thus exhibit several physical and chemical properties similar. Niobium is used in many technologically important applications, and Brazil has the largest reserves, around 96%. These electrolytic capacitors have high specific capacitance, so they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium poder was first characterized by XRD, SEM and laser particle size to then be sieved into particle size 400mesh. The powder was then compacted at pressure of 150MPa and sintered at 1400, 1450 and 1500?C using two sintering time 30 and 60min. Sintering is an important part of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. After sintering the samples were underwent a process of anodic oxidation (anodizing), which created a thin film of niobium pentoxide over the whole surface of the sample, this film is the dielectric capacitor. The anodizing process variables influenced a lot in film formation and consequently the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor and ESR (equivalent series resistance). The sintering has affected the porosity and in turn the specific area of the samples. The capacitor area is directly related to the capacitance, that is, the higher the specific area is the capacitance. Higher sintering temperatures decrease the surface area but eliminate as many impurities. The best results were obtained at a temperature of 1400?C with 60 minutes. The most interesting results were compared with the specific capacitance and ESR for all samples.
Identifer | oai:union.ndltd.org:IBICT/oai:repositorio.ufrn.br:123456789/21165 |
Date | 08 April 2016 |
Creators | Nascimento, Edson Silva do |
Contributors | 05012180410, http://lattes.cnpq.br/9858094266525225, Gomes, Uilame Umbelino, Silva, Ariadne de Souza, 00735940401, http://lattes.cnpq.br/5623381698478389, Tavares, Elcio Correia de Souza, 49047914449, http://lattes.cnpq.br/4400396552273448, Costa, Francine Alves da, 45327220478, http://lattes.cnpq.br/8698567925323942, Gomes, Uilame Umbelino |
Publisher | Universidade Federal do Rio Grande do Norte, PROGRAMA DE P?S-GRADUA??O EM CI?NCIA E ENGENHARIA DE MATERIAIS, UFRN, Brasil |
Source Sets | IBICT Brazilian ETDs |
Language | Portuguese |
Detected Language | English |
Type | info:eu-repo/semantics/publishedVersion, info:eu-repo/semantics/masterThesis |
Source | reponame:Repositório Institucional da UFRN, instname:Universidade Federal do Rio Grande do Norte, instacron:UFRN |
Rights | info:eu-repo/semantics/openAccess |
Page generated in 0.0017 seconds