This thesis focuses on the development of a new method for the continuous<p>monitoring of civil engineering structures in order to locate small damages automatically. A<p>review of the very wide literature on Structural Health Monitoring (SHM) points first out that<p>the methods can be grouped in four categories based on their need or not of a numerical model,<p>as well as their need or not of information of the damaged structure to be applied. This state<p>of the art of the SHM methods highlights the requirement to reach each levels of SHM, which<p>is in particular for the localization of small damages in civil engineering structures the needs<p>for a non-model based output-only damage sensitive feature extraction technique. The origin of<p>the local sensitivity of strains to damages is also analyzed, which justifies their use for damage<p>localization.<p>A new method based on the modal filtering technique which consists in combining linearly<p>the sensor responses in a specific way to mimic a single degree of freedom system and which<p>was previously developed for damage detection is proposed. A very large network of dynamic<p>strain sensors is deployed on the structure and split into several independent local sensor networks.<p>Low computational cost and fast signal processing techniques are coupled to statistical<p>control charts for robust and fully automated damage localization.<p>The efficiency of the method is demonstrated using time-domain simulated data on a simply<p>supported beam and a three-dimensional bridge structure. The method is able to detect and<p>locate very small damages even in the presence of noise on the measurements and variability<p>of the baseline structure if strain sensors are used. The difficulty to locate damages from acceleration<p>sensors is also clearly illustrated. The most common classical methods for damage<p>localization are applied on the simply supported beam and the results show that the modal filtering<p>technique presents much better performances for an accurate localization of small damages<p>and is easier to automate.<p>An improvement of the modal filters method referred to as adaptive modal filters is next<p>proposed in order to enhance the ability to localize small damages, as well as to follow their<p>evolution through modal filters updating. Based on this study, a new damage sensitive feature<p>is proposed and is compared with other damage sensitive features to detect the damages with<p>modal filters to demonstrate its interest. These expectations are verified numerically with the<p>three-dimensional bridge structure, and the results show that the adaptation of the modal filters<p>increases the sensitivity of local filters to damages.<p>Experimental tests have been led first to check the feasibility of modal filters to detect damages<p>when they are used with accelerometers. Two case studies are considered. The first work<p>investigates the experimental damage detection of a small aircraft wing equipped with a network<p>of 15 accelerometers, one force transducer and excited with an electro-dynamic shaker. A<p>damage is introduced by replacing inspection panels with damaged panels. A modified version<p>of the modal filtering technique is applied and compared with the damage detection based principal<p>component analysis of FRFs as well as of transmissibilities. The three approaches succeed<p>in the damage detection but we illustrate the advantage of using the modal filtering algorithm as<p>well as of the new damage sensitive feature. The second experimental application aims at detecting<p>both linear and nonlinear damage scenarios using the responses of four accelerometers<p>installed on the three-storey frame structure previously developed and studied at Los Alamos<p>National Labs. In particular, modal filters are shown to be sensitive to both types of damages,<p>but cannot make the distinction between linear and nonlinear damages.<p>Finally, the new method is tested experimentally to locate damages by considering cheap<p>piezoelectric patches (PVDF) for dynamic strain measurements. Again, two case studies are investigated.<p>The first work investigates a small clamped-free steel plate equipped with 8 PVDFs sensors, and excited with a PZT patch. A small damage is introduced at different locations by<p>fixing a stiffener. The modal filters are applied on three local filters in order to locate damage.<p>Univariate control charts allow to locate automatically all the damage positions correctly.<p>The last experimental investigation is devoted to a 3.78m long I-steel beam equipped with 20<p>PVDFs sensors and excited with an electro-dynamic shaker. Again, a small stiffener is added to<p>mimic the effect of a small damage and five local filters are defined to locate the damage. The<p>damage is correctly located for several positions, and the interest of including measurements<p>under different environmental conditions for the baseline as well as overlapping the local filters<p>is illustrated.<p>The very nice results obtained with these first experimental applications of modal filters<p>based on strains show the real interest of this very low computational cost method for outputonly<p>non-model based automated damage localization of real structures. / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished
| Identifer | oai:union.ndltd.org:ulb.ac.be/oai:dipot.ulb.ac.be:2013/209466 |
| Date | 26 April 2013 |
| Creators | Tondreau, Gilles |
| Contributors | Deraemaeker, Arnaud, Espion, Bernard, Kullaa, Jyrki, Worden, Keith, Kinnaert, Michel, De Roeck, Guido |
| Publisher | Universite Libre de Bruxelles, Université libre de Bruxelles, Ecole polytechnique de Bruxelles – Constructions, Bruxelles |
| Source Sets | Université libre de Bruxelles |
| Language | English |
| Detected Language | English |
| Type | info:eu-repo/semantics/doctoralThesis, info:ulb-repo/semantics/doctoralThesis, info:ulb-repo/semantics/openurl/vlink-dissertation |
| Format | 1 v. (167 p.), No full-text files |
Page generated in 0.0029 seconds