A dissertation submitted to the Faculty of Science, University of the Witwatersrand,
Johannesburg, in fulfilment for the degree of Master of Science in Chemistry. Johannesburg 2016. / In the current study, different platinum-hollow carbon sphere catalysts were synthesized for use as electrocatalysts in low temperature fuel cells such as proton exchange membrane fuel cells (PEMFCs). The support material was synthesized via a hard templating method using mesoporous silica (synthesized using a modified Stöber method) as a sacrificial template. In fuel cells, one aim is to ensure that as much platinum as possible is present on a given electrode while keeping the entirety of the catalytic layer as thin as possible (i.e. with the minimum amount of carbon). One approach to achieving this was to make the hollow carbon spheres as small as possible, starting of course with the templating material. It was found that tailoring the molar ratios between the two co-solvents (that is water and ethanol) during Stöber synthesis was the key to achieving particles as small as approximately 150 nm with a uniform shape, size, and significant yields of up to 5.00 g.
Another focal point in terms of the template material was achieving a silica structure that consisted of a solid core, and a distinctly mesoporous shell. Two different surfactants were explored in order to fabricate these structures; namely octadecyltrimethoxysilane (C18TMS) and cetyltrimethylammonium bromide (CTAB). It was found that of the two, the C18TMS resulted in more distinctly formed mesoporous silica layers with higher measured specific surface areas.
Because the type of support material greatly influences the catalytic behaviour of the loaded catalysts, two different carbonization techniques were explored; namely the bubbling method using toluene as a carbon source, and a nanocasting method where resorcinol formaldehyde (RF) was the carbon source. The toluene-synthesized hollow carbon spheres had advantages over their RF-synthesized counterparts in that they were more thermally stable and had a more graphitic crystalline carbon framework. The RF-synthesized carbon, however, possessed a pseudo-capacitance due to surface carbon-oxygen groups, as well as a higher specific surface area, which resulted in the RF-carbon cyclic voltammetry profile spanning a larger current range in microampere per square centimetre.
The effect of the size of the support materials was also explored; comparing 350 nm and 150 nm hollow carbon spheres. Besides the type of carbon, the metal precursor used to synthesize the catalyst nanoparticles was also explored, with either platinum(II)chloride (PtCl2) or platinum(II)acetylacetonate [Pt(acac)2] being used as the platinum source. It is also known that achieving high metal yields using conventional methods is quite difficult, and so an easier, quicker and less wasteful method was also explored; comparing the traditional wet-impregnation (WI) method with a chemical vapour deposition (CVD) method. Ultimately, it was found that platinum loaded on top of small-sized toluene-synthesized hollow carbon spheres using the CVD method and Pt(acac)2 as the metal precursor was the better catalyst in terms of oxygen reduction (determined using linear sweep voltammetry measurements); outperforming even commercial Pt/C catalysts as a result of improved mass transfer afforded by the voided cores of the hollow carbon spheres.
The ability of a catalyst to withstand the reaction conditions present in a PEM fuel cell (i.e. oxygen-rich environments) was also considered. The stability of the catalysts was tested using chronoamperometry measurements in an oxygen-saturated perchloric acid solution. It was evident that the platinum loaded on the inner shells of the hollow carbon spheres showed far superior stability to those loaded on the outside surface. This was attributed to the qualities bestowed by the carbon shell around the platinum nanoparticles, protecting said platinum against the consequences of support corrosion due to the oxygenated environment; consequences such as metal sintering and interaction with surrounding carbon supports for example. These encapsulated catalysts, however, displayed a decrease in electrocatalytic activity compared to the catalysts with top-loaded platinum.
In conclusion, the study of different platinum-carbon catalysts studied in the current work revealed that (a) loading platinum on top of small sized toluene-synthesized hollow carbon spheres using a CVD method and Pt(acac)2 as a metal precursor resulted in a highly active oxygen reduction catalyst, while (b) loading platinum on the inside surface of the hollow carbon spheres under the dame conditions resulted in a more electrocatalytically stable catalyst. / LG2017
| Identifer | oai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:wits/oai:wiredspace.wits.ac.za:10539/21747 |
| Date | January 2016 |
| Creators | Phago, Evah Ramokone |
| Source Sets | South African National ETD Portal |
| Language | English |
| Detected Language | English |
| Type | Thesis |
| Format | Online resource (xvii, 118 leaves), application/pdf |
Page generated in 0.0026 seconds