Georgia Institute of Technology
Characterizing Thermal Gradients in Solid Oxide Fuel Cells Using a Phenomenon-In-Loop Simulation Approach
Abstract
dc:description.abstractSolid oxide fuel cells (SOFCs) are high-temperature electrochemical devices capable of electrical efficiencies exceeding 60%, yet their operation between 600°C and 1000°C introduces significant thermal management challenges. Non-uniform heat generation throughout the cell stack produces spatial thermal gradients that induce thermomechanical stress, material degradation, and reduced operational lifespan. Despite extensive computational modeling of this phenomenon in the literature, hardware-based experimental validation of SOFC thermal gradient formation remains scarce, owing to the high cost, safety constraints, and fragility of real fuel cell components. This thesis addresses that gap through the design, fabrication, and experimental validation of a physical thermal analog of an SOFC (inclusive of interconnect stack), operated within a phenomenon-in-loop simulation (PILS) framework. The thermal analog consists of a metal additive-manufactured SS316 stainless steel plate housing nineteen air flow channels of 2 mm × 2 mm cross-section, sixteen independently addressable Rauschert ceramic heaters capable of sustained operation above 750 °C, and a Type-K thermocouple array embedded directly within the interconnect plates. A one-dimensional electrochemical and thermal SOFC model, implemented in MATLAB/Simulink, is coupled in real time to a LabVIEW hardware control layer in a closed-loop cyber-physical architecture. In this configuration, experimentally measured plate temperatures are continuously fed back into the electrochemistry computational model, which in turn computes spatially resolved heat generation setpoints that are imposed on the ceramic heaters via pulse-width-modulated power delivery — without any actual reactions or hydrogen supply. Prior to PILS validation, a series of preparatory experiments were conducted. Four iterations of thermal enclosure design reduced steady-state parasitic heat losses by 34%, bringing the energy rate required to maintain the replica at 600 °C from 460 W to 305 W. Baseline calibration experiments quantified the global heat transfer propensity of the enclosure across 500°C –700°C, revealing a temperature-dependent increase from 0.51 W/K to 0.61 W/K (+19.6%). This increase was driven by radiative heat transfer scaling with T⁴ — establishing a variable “thermal tare” essential for accurate energy balance calculations. Structural redesign of the manifold clamping assembly, incorporating a high-stiffness SS316 U-channel beam and Belleville spring washers, reduced air leakage from an initial 95% bypass to a residual mean of 17.1%, cross-validated by dual anemometry and Nusselt-number inference methods. A parallel pre-heater configuration was developed to deliver stable inlet air temperatures of 300°C –400°C, in order to prevent thermal shock to the replica during active-flow experiments. PILS experiments conducted at a nominal 600 °C with a simulated 200 A load (0.5 A/cm² mean current density, 20.7% fuel utilization) produced a spatially resolved dataset of thermal gradient formation. The spatial current density profile exhibited a clear inlet-to-outlet gradient (0.53 A/cm² to 0.47 A/cm²), reflecting progressive reactant depletion along the channel length and confirming physically expected electrochemical behavior. Interior node heat generation ranged from 6.0 W to 6.8 W per slice, with peak values near the fuel inlet. A stable open-circuit voltage of 0.907 V and an operating voltage of 0.52 V –0.58 V under PILS load confirmed the coherence of the closed-loop feedback architecture. Thermal efficiency stabilized in the 20-25% range, consistent with the parasitic loss characteristics of a laboratory-scale enclosure. The work demonstrates that the dominant thermal physics of an SOFC arrangement can be experimentally characterized using air flow and ceramic heaters within a thermal replica, substantially reducing the barrier to entry for SOFC thermal research. The PILS platform represents a first-generation infrastructure for hardware-in-the-loop thermal simulation of solid oxide fuel cells, with identified pathways toward multi-plate stack extension, improved sealing, denser instrumentation, and full digital twin capability through model-predictive control.
Degree
thesis:*- Name thesis:degree_name
- Mechanical Engineering, MS
- Department thesis:degree_department
- Mechanical Engineering
- Grantor
- Georgia Institute of Technology
- Year dc:date.issued
- 2026
Author and committee
dc:creator, dc:contributor.*- Author dc:creator
-
- Rubino, Arthur Pierre Antoine
- Advisor dc:contributor.advisor
-
- Haynes, Comas
- Committee members dc:contributor.committeemember
-
- Ghiaasiaan, S.
- Loutzenhiser, Peter
Rights
- Language dc:language.iso
- English
Identifiers
dc:identifier.*- Handle dc:identifier.uri
- https://hdl.handle.net/1853/81607