Back to search

Georgia Institute of Technology

Analysis of External End Effector Feedback Control for Industrial Robotic Manipulators

Abstract

dc:description.abstract

Industrial serial manipulators are promising alternatives to traditional Computer Numerical Control (CNC) machines commonly used for machining large aerostructures due to their relatively low cost, smaller footprint, and reconfigurability. A key challenge to overcome is the low global positioning accuracy of these manipulators. One way to address this is through an external feedback control loop that measures and corrects position inaccuracies, but these systems include command delays that affect the ability of the external feedback loop to correct position errors. Furthermore, rapid changes in the direction of motion can excite residual vibrations of the flexible manipulator that also affect path following accuracy. This thesis aims to improve the tracking accuracy of 6 degree-of-freedom (DoF) industrial robotic serial link manipulators by addressing the command delay when implementing external position feedback control and by mitigating the residual vibrations. First, a method of compensating for the command delay in the external position feedback loop of the 6 DoF industrial serial link manipulator using a Smith predictor is presented. The external position feedback controller implemented utilizes a proportional-integral (PI) controller to correct position errors measured using a laser tracker. During trajectory tracking, in the presence of a command delay, the integral action creates an accumulated control effort that results in overshoot when rapid changes in the direction of motion occur. To address this, the command delay is measured throughout a subspace of the robot’s workspace. Then, a Smith predictor is implemented in the control algorithm of the external position feedback controller to compensate for this delay. The resulting control algorithm significantly reduces the integral build up and overshoot that was observed without the Smith predictor implemented. In a trajectory with orthogonal corners traversed at 3048 mm/min, the maximum overshoot was reduced from 2.8 mm to 1.2 mm with the implementation of the Smith predictor. Second, a method for reducing the residual vibrations of the 6 DoF serial link manipulator while following a trajectory of discrete linear segments with sharp corners using input shaping is presented. Input shaping filters the reference trajectory such that the residual vibrations from a command input cancel each other out. To inform the input shaper, the natural frequency and damping ratio of the robot are measured throughout a subspace of the robot’s workspace. A time-varying input shaper is created using the average damping ratio over the subspace, while the natural frequency is predicted using a Gaussian Process Regression (GPR) model trained on the measured natural frequency as a function of the robot’s location in the cartesian workspace. The time-varying input shaper is then applied to cartesian trajectories of discrete linear segments with sharp corners along the path. The resulting mean and maximum path error was reduced by an average of 26% and 37%, respectively, relative to an unshaped trajectory. Finally, the effectiveness of using input shaping on trajectories of discrete linear segments with sharp corners to improve path following accuracy is demonstrated through the robotic machining of a carbon fiber reinforced polymer (CFRP) sample. Samples of CFRP were machined using trajectories with sharp corners along the path, both with and without input shaping, and the finished samples were measured on a coordinate measuring machine (CMM). The finished dimensions of the samples machined using input shaped trajectories had a maximum deviation of 0.31 mm compared to a maximum deviation without input shaping of 0.51mm.

Degree

thesis:*
Level thesis:degree_level
Masters
Department dc:contributor.department
Mechanical Engineering
Grantor dc:publisher
Georgia Institute of Technology
Year dc:date.issued
2025

Author and committee

dc:creator, dc:contributor.*
Author dc:creator
  • Kubista, Michael S.
Advisor dc:contributor.advisor
  • Melkote, Shreyes N.
Committee members dc:contributor.committeemember
  • Kurfess, Thomas
  • Balakirsky, Stephen

Subjects

dc:subject × 4

Rights

Language dc:language.iso
en_US

Identifiers

dc:identifier.*
Handle dc:identifier.uri
https://hdl.handle.net/1853/82064

Chain of custody

source
Harvested from
Georgia Tech
Base URL
repository.gatech.edu/server/oai/request
Last updated
2026-11-19
Source record
OAI-PMH GetRecord
citation

Kubista, Michael S.. Analysis of External End Effector Feedback Control for Industrial Robotic Manipulators. Masters thesis, Georgia Institute of Technology, 2025. https://hdl.handle.net/1853/82064