Back to search

Aristotle University Of Thessaloniki (AUTH)

Ανάπτυξη νέων σύνθετων υλικών βιοπολυμερούς-βιοκεραμικού για εφαρμογές ιστομηχανικής

Abstract

dc:description

The main objective of the thesis is the development of novel materials for fabrication of tissue engineering scaffolds. The desirable characteristics of a tissue engineering scaffold are biodegradation, biocompatibility and the existence of porous structure. The first two characteristics can be rather easily satisfied by choosing an appropriate starting material for the fabrication of the scaffold (e.g. a natural polymer), so the main subject of the present thesis is focused on the production of porous structures out of biodegradable-biocompatible polymers. Initially, fibrous cellulose acetate and poly(hydroxyl butyrate) (PHB) structures were successfully prepared via the electrospinning technique. The structures exhibited an average diameter size between 0.6 and 3 μm. In the fibrous scaffolds of PHB piroxicam was encapsulated while amoxicillin was loaded in the cellulose acetate scaffolds. In both cases the loading percentage was low. It was found that increase of the drug concentration in the initial solution does not lead to an increase in the loading percentage. Next, the particulate leaching method was used in order to produce porous chitin and chitin-hydroxyapatite structures. According to the literature, salt (water soluble) particles were used. It was found that this method cannot be applied successfully in hydrophilic polymers like chitin due to the simultaneous removal of the polymer solvent and the porogen particles. Thus, next water insoluble particulates were used. This approach was successfully applied to chitin, cellulose, chitosan and composite materials of chitin-hydroxyapatite, cellulose-hydroxyapatite and chitosan-gelatin. The produced structures exhibited great uniformity, high and open porosity. The use of ionic liquids as solvents, in the case of cellulose, enables the process and the production of composite materials. By the in situ fabrication of scaffolds with the above mentioned method in porcelain samples, connection of chitin, chitosan and chitosan-gelatin scaffolds with porcelain was achieved. The connection was by infrared spectroscopy and it was found that mainly responsible for this, is the interaction via dispersion forces between groups of the polymers and the porcelain sample. The ceramic connected with polymer scaffolds is a composite biomaterial. Other composite biomaterials that consist of two or three scaffolds were fabricated by combining different techniques. The connection between the scaffolds was achieved due to dispersion forces or hydrogen bonds. Such a material could possibly find application in multiple tissue or tissue interface regeneration. By using supercritical CO2 porous poly(methyl methacrylate) structures were produced via the polymer foaming (temperature induced) method. The influence of the polymer thickness was examined. In all cases sub-micron porous were obtained and it was found that by increasing thickness the average pore diameter and the dispersion increase. For qualitative theoretical explanation of the results the activation energy of homogeneous nucleation was determined by taking into account the kinetics of heat and mass transfer in these samples. For the production of porous structures, by using CO2, in crystalline polymers such as chitin and cellulose a novel method, that was developed during the thesis, was applied: the hydrogel foaming. Porous chitin, cellulose, cellulose-hydroxyapatite and cellulose-silicon oxide structures were produced with an average diameter between 30 and 150 μm. It was found that by increasing pressure or decreasing temperature, average pore diameter decreases. The incomplete desorption of CO2 from the hydrogel in some cases (that arises from cooling due to the Joule-Thomson effect) leads to an increased pore interconnection. If instead of hydrogels alco-gels are used it was found that via the critical point drying technique (and by using supercritical CO2) nanoporous chitin and cellulose aerogels can be prepared. The influence of different parameters on the characteristics of the final material was examined. Also the feasibility of producing carbon aerogel with chitin aerogel as precursor was examined. The foaming of alco-gels was found to be defective. This was attributed to the crystallinity of the gels. Hydrogels can be considered as amorphous polymer in the rubbery state (flexible chains), where the CO2 desorption leads to pore formation. In contrast, in the case of alco-gels the production of porous structure depends exclusively on the interaction of CO2 with the solvent of the gel. The sorpion of CO2 by chitin and cellulose hydrogels was measured by a modified mass loss analysis. Also an apparatus was designed and constructed that combines volumetric method and Calvet calorimetry. ....................................................................................................................................................................................................................

Degree

thesis:*
Grantor dc:publisher
Aristotle University Of Thessaloniki (AUTH)
Year dc:date
2009

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Tsioptsias, Constantinos
  • Τσιόπτσιας, Κωνσταντίνος

Subjects

dc:subject × 12

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/19327

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Tsioptsias, Constantinos; Τσιόπτσιας, Κωνσταντίνος. Ανάπτυξη νέων σύνθετων υλικών βιοπολυμερούς-βιοκεραμικού για εφαρμογές ιστομηχανικής. Aristotle University Of Thessaloniki (AUTH), 2009. http://hdl.handle.net/10442/hedi/19327