Back to search

Aristotle University Of Thessaloniki (AUTH)

Πειραματική μελέτη της παρασκευής λιπασμάτων ελεγχόμενης απελευθέρωσης με τη βοήθεια φυσικών και χημικών μεθόδων εγκλεισμού

Abstract

dc:description

The scope of the present study is to investigate the production of a slow release fertilizer by employing chemical and physicochemical methods. First a literature survey was made in order to specify the different categories of slow release fertilizers and to determine the advantages and disadvantages of the products of each category. It was evident that coated fertilizers were superior compared to other slow release fertilizers due to the fact that the release rate of the nutrients is affected almost exclusively by the properties of the coating. As a result coated fertilizers can release their nutrients not only in a slow rate but also in a controlled manner. The coating process can be carried out in different kind of equipment. The equipment that creates coating of the higher quality is the fluidized bed. In the coating experiments of the present thesis, a modified type of a fluidized bed, known as the Wurster fluidized bed, was employed, because in it the granules during the coating process follow a certain flow pattern, which facilitates the uniform coating of the fertilizer granules. In the second chapter the variables that influence the coating process are presented and are categorized in two groups, which are studied separately. The first group consists of the parameters that influence the flow pattern of the granules inside the fluidized bed. These variables are: a) the type of the perforation plate through which enters the fluidization air, b) the distance of the partition from the bottom of the fluidized bed, c) the velocity of the fluidization air και d) the size and the size distribution of the granules. The experimental study of the above parameters showed the following results: for this kind of granules (large size, high density), a high air flow rate is necessary to exist in the descending zone, in order to avoid the collision of the granules to the bottom of the vessel. Therefore, the perforation percentage of the perforated plate in the area, which corresponds at the descending zone, must be as high as possible. The distance of the partition should be such that would not disturb the regular flow of the granules inside the bed during the coating process. For the given fertilizer granules due to their large size (diameter between 2,5- 4 mm), the flow pattern is disturbed more when the distance becomes small (< 2.5 cm). The velocity of the fluidization air should be high enough in order to facilitate a regular flow pattern but not as high as to provoke collisions among the granules and among the granules and the coating vessel. Finally, it is worth noting that the quality of the polymer film that is built around the fertilizer granules is of considerably superior quality when the substrate during the coating process has narrow size distribution. In fact, substrate of small size is preferred because in this case the release profile of the nutrients is affected in larger extend by the characteristics of the coating and not by the defects of the coating. The second group consists of the parameters, which influence the film forming phenomena during the coating process. The variables of this group are a) the temperature of the fluidization air at the inlet, b) the temperature of the atomization air, c) the pressure of the atomization air, d) the spray rate of the latex and e) the characteristics of the coating material. The experimental study of the above parameters led to the following conclusions. The temperature in the bed should be 10°C to 15°C above the glass transition temperature (Tg) of the polymer. Thus, the temperature of the fluidization air at the inlet of the bed must be 20 - 25°C above Tg. Furthermore, it is best if the temperature of the atomization air is the same to the temperature of the fluidization air at the inlet of the bed. In this way temperature disturbances during the spraying process are avoided. The pressure of the atomization air is the variable that affects the quality of the coating in the greater extent. When the pressure of the atomization air has the lower value necessary to provoke atomization of the latex, then the quality of the coating is excellent. The spray rate of the latex also affects the quality of the coating. For the given granules, which exhibit a highly irregular surface, it is best if they are coated by employing a slow spraying rate. Considering the characteristics of the coating material, polymer films with high crystalline percentage, such as the ones produced by the vinylidene chloride co-polymers, exhibit lower permeability. Moreover in order to produce a uniform film around the fertilizer granules under mild conditions, it is necessary to employ latex with high solid percentage and low Tg. In the 6th chapter of this thesis is displayed a mathematical model in order to describe the release process of the nutrients from the core of the coated granules to the environment (distilled water). By making the assumption that the nutrients diffuse through the polymer coating under pseudo-state conditions and that the diffusion coefficient of the polymer film is changing exponentially with time due to the photo-degradation of the coating, the theoretical prediction is in agreement with the experimental data. Finally some comparative release experiments in distilled water among the coated fertilizer produced in the laboratory and two commercial products were conducted. The release rate of the nutrients from the coated fertilizer produced in the laboratory was considerably lower than the release rate that exhibit the commercial products. Thus, the results of the experiments are encouraging and they indicate that the coated fertilizer which was produced in the laboratory is of high quality.

Degree

thesis:*
Grantor dc:publisher
Aristotle University Of Thessaloniki (AUTH)
Year dc:date
2002

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Τζήκα, Μαρία
  • Tzika, Maria

Subjects

dc:subject × 20

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/20235

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Τζήκα, Μαρία; Tzika, Maria. Πειραματική μελέτη της παρασκευής λιπασμάτων ελεγχόμενης απελευθέρωσης με τη βοήθεια φυσικών και χημικών μεθόδων εγκλεισμού. Aristotle University Of Thessaloniki (AUTH), 2002. http://hdl.handle.net/10442/hedi/20235