Back to search

Aristotle University Of Thessaloniki (AUTH)

Σύνθεση και χαρακτηρισμός πορωδών υλικών για την εφαρμογή τους στην απομάκρυνση ρύπων από υδατικά διαλύματα

Abstract

dc:description

In the present study new synthetic mesoporous carbons (CMK-3 and DMC), mesoporous silica materials type HMS and the modified derivatives with aminogroups or cyclodextrine (HMS-NH2, HMS-CD2%, HMS-CD4% and HMS-CD6%) and layered double hydroxide (Mg-Al and Mg-Fe calcined and non-calcined) were investigated for the sorption of Remazol Red 3BS from aqueous solutions in comparison to three commercial activated carbons (Norit SAE-2, Takeda 5A and Calgon). The structural, porosity and surface characteristics of the sorptive materials were evaluated using XRD, N₂ porosimetry, TEM, SEM, FT-IR spectroscopy and zeta-potential measurements. The sorbent materials were tested for the sorption of Reactive Red dye from aqueous solutions at room temperature using the batch technique. The effect of several variables (pH, dye concentration, contact time, temperature and the desorption of dye from the loaded sorbents) was studied. The amount of dye retained in the sorbent phase (mmol/g) was measured by UV-Vis spectrophotometer at 541 nm. In case of carbon (CMK-3, DMC, Norit SAE-2, Takeda 5A, Calgon) and silica (HMS, HMS-NH2, HMS-CD2%, HMS-CD4%, HMS-CD6%) sorbents, the increment at pH values of the dye solution caused reduction of sorption capacity of the above materials. The more favourable pH for these sorbents is 2. In the case of calcined and non-calcined layered double hydroxides (Mg-Al and Mg-Fe) the sorption was more favourable at the pH value of 6. Equilibrium sorption data followed the Langmuir model and showed that the two synthetic mesoporous carbons CMK-3 and DMC exhibit higher sorption capacities (0.533 και 0.453 mmol/g, respectively), while in the case of sorbents based on silica, the HMS-CD2% showed the highest sorption capacity (0.275 mmol/g). In the case of layered double hydroxides, the maximum adsorption of dye was observed on calcined hydrotalcite Mg-Al (0.125 mmol/g). Sorption experiments at three different temperatures (25, 45 and 65°C) showed that the temperature increase resulted in increased sorption capacity of the above sorbent materials. The effect of contact time on the amount of dye adsorbed by the different materials showed that the adsorption process was rapid at the beginning and after 180 min there was no significant increase in the removal of dye up to 24 h for the sorbent materials. The description of the sorption behavior with time follows the second-order model. The effect of solution pH on regeneration efficiency from the loaded sorbent materials was negligible. Efficient desorption was achieved by the use of aqueous solution of sodium-dodecyl-sulfate as surfactant. After the third cycle of adsorption-desorption the loss of sorption capacity for the sorbents was relatively low, except that in the case of hydrotalcite Mg-Al in which at the second cycle of sorptiondesorption the sorption capacity reduced.

Degree

thesis:*
Grantor dc:publisher
Aristotle University Of Thessaloniki (AUTH)
Year dc:date
2008

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Asouhidou, Despoina
  • Ασουχίδου, Δέσποινα

Subjects

dc:subject × 20

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/25854

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Asouhidou, Despoina; Ασουχίδου, Δέσποινα. Σύνθεση και χαρακτηρισμός πορωδών υλικών για την εφαρμογή τους στην απομάκρυνση ρύπων από υδατικά διαλύματα. Aristotle University Of Thessaloniki (AUTH), 2008. http://hdl.handle.net/10442/hedi/25854