National Technical University of Athens (NTUA)
Ανάπτυξη και τεχνολογικές ιδιότητες προηγμένου κράματος αλουμινίου 7075
Abstract
dc:descriptionAluminium and its alloys are widely used in various technological and industrial applications, due to their physical, chemical and thermal properties. However, the mechanical strength of aluminium is limited. In the past decade a variety of aluminium alloys has been produced, in order to fulfill the increasing demand for innovative materials in various technological and industrial fields. In this Ph.D. Thesis, the effect of zirconium addition (0.2 w.t%) on some technological properties of 7075 aluminium alloy was investigated. The results that extracted compared with those of aluminium 7075 without zirconium. Aluminium 7075 alloy with zirconium addition was produced by induction melting. The 7075 aluminium alloy is one of the most important engineering alloys and has been utilized extensively in the aerospace and automotive industries by virtue of its high mechanical strength and low weight. For the production of 7075 aluminium alloy the following master alloys Al-Cu, Al-Zn-Mg and Al-Zr were melted. The melts were prepared by placing 20gf master alloys in a clay bonded graphite crucible coated with boron nitride and melting in an induction furnace. Structural and metallographical study of 7075 alloy was performed with the aid of X-ray Diffraction (XRD), Metallurgical Microscopy, Scanning Electron Microscopy (SEM), Electron Dispersive Spectroscopy (EDS), Electron Backscattering Diffraction (EBSD) and Transmission Electron Microscopy (TEM) techniques. Aluminium 7075 with zirconium was found to consist of: (a) aluminium-zinc-magnesium solid solution, (b) Al3Zr (c) Mg(ZnCu)2, (d) Al7Cu2Fe and (e) Al2CuMg intermetallic phases. As revealed the grains of the 7075 aluminium alloy containing 0.2 w.t% zirconium were refined and this is might be due to the precipitation of binary Al3Zr at the Al matrix and grain boundaries too, during casting process. In addition the zirconium doped 7075 alloy exhibited higher microhardness values compared to that without zirconium. The tribological behaviour of 7075 alloy with and without zirconium addition, under dry and lubricated conditions, was also examined. The results showed that the addition of zirconium led to lower values of friction coefficient of aluminuium 7075 with zirconium – stainless steel tribosystem. The addition of zirconium was also found to decrease the wear rate of this system. The influence of zirconium addition on the corrosion behavior of aluminium 7075 was also examined. It was observed that the addition of zirconium decreases the corrosion resistance of the alloy. This may be attributed to the higher volume fraction of η΄ precipitates finely distributed along the grain boundaries of zirconium doped aluminium alloy. Finally, the effect of this minor addition on the hydrogen absorption and embrittlement of 7075 aluminium alloy was investigated. Zirconium addition led to increased number of trapping sites in the alloy and this may be due to the fact that zirconium and magnesium compounds have strong affinity with hydrogen and are irreversible traps for it.
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2009
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Lagaris, Dimitrios
- Λάγαρης, Δημήτριος
Subjects
dc:subject × 18- Κράματα αλουμινίου
- Χύτευση
- Δομή και χαρακτηρισμός
- Διάβρωση
- Καθοδική φόρτιση με υδρογόνο
- Τριβή και φθορά
- Λιπαντικά
- Aluminium alloys
- Casting
- Structural characterization
- Corrosion
- Hydrogen charging
- Friction and wear
- Lubricants
- Engineering and Technology
- Chemical Engineering
- Επιστήμες Μηχανικού και Τεχνολογία
- Επιστήμη Χημικού Μηχανικού
Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/26258