Back to search

National Technical University of Athens (NTUA)

Φωτοηλεκτροχημεία ηλεκτροαποθεμάτων Cd(Zn)Se: παρασκευή και χαρακτηρισμός φωτο-ηλεκτροδίων TiO2/CdSe

Abstract

dc:description

The dissertation was completed under the guidance of Assistant Professor Dr. Mirtat Bouroushian and the advisory committee of Emeritus Professor Dr. Niki Kouloumbi, and Associate Professor Dr. Zafiris Loizos, at the School of Chemical Engineering in the National Technical University of Athens. The major part of the experimental research was conducted in the Laboratory of General Chemistry of the Chemical Sciences Section. The subject-matter of this Thesis is a close examination of various aspects of the structural and photoelectrochemical properties of IIΒ–VIΒ metal selenide compound semiconductors. Specifically, the present work aimed to: (A) analyze the complexity of the unstable semiconductor/electrolyte liquid junction, and provide experimental data about the evolution of electrode photocorrosion phenomena (Chapters II-1 to II-4). (B) examine the possibility of titanium oxide photosensitization by CdSe (Chapters II-5 to II-7). The above two points correspond to self-consistent parts of the experimental section (Parts A & B). In brief, thin films or nanocrystalline aggregate layers of cadmium and zinc selenide binary and ternary phases (CdSe, ZnSe, ZnxCd1-xSe) were prepared by electrodeposition on metal (Ni, Ti), or oxide (TiO2) substrates and studied by solid state characterization techniques, such as X-Ray Diffraction (Bragg–Brentano geometry/XRD, Low Incidence Angle/LIXD) and Scanning Electron Microscopy (SEM) with Energy Dispersive Analysis of X-Rays (EDAX). Further, they were used as photo-absorbing electrodes in photoelectrochemical cells (PEC), in contact with redox and indifferent electrolytes, and characterized by a number of (photo)electrochemical techniques. The Thesis is divided into three sections: Section I emphasizing on theoretical aspects of photoelectrochemistry (Chapters I-1 to I-5), Section II, which is the experimental part, with subdivisions A for Cd(Zn)Se electrodeposits on metal substrates (Chapters II-1 to II-4) and B for CdSe electrodeposits on titanium oxide substrates (Chapters II-5 to II-7); Section III, including appendices for symbols, abbreviations and terms, followed by the list of cited bibliography. The contents of each chapter are summarized below: Chapter I-1: Theoretical description of the semiconductor and the redox-electrolyte phases. Energy band diagram for each separate phase. Chapter I-2: Theoretical description of the semiconductor/electrolyte junction. Energy band diagrams and band-bending. Chapter I-3: The Photoelectrochemical Cell (PEC). Current–Potential characteristics and photocorrosion. Chapter I-4: Photosensitization of TiO2 electrodes. Chapter I-5: Electrochemical Impedance Spectroscopy (EIS) on semiconductor electrodes. The Mott-Schottky diagram. Chapter II-1: CdSe photoelectrodes – bibliographical data. Energy band edges, surface states and photocorrosion. Chapter II-2: CdSe photoelectrodes in contact with various electrolytes. Experimental data from (photo)voltammetry – estimation of redox potentials and CdSe energy band edges. Chapter II-3: Photocurrent spectroscopy on ZnxCd1-xSe photoelectrodes. Estimation of energy bandgap width and its dependence on the content variable x. Chapter II-4: Photocurrent chronoamperometry on single-layer CdSe and double-layer CdSe/ZnSe photoelectrodes in contact with sulfide/polysulfide (SPS) and ferro-ferri-cyanide (FFC) redox electrolytes. A photocorrosion study. Chapter II-5: Titanium anodization (nanotube formation) and TiO2 – CdSe energy band edge comparison (photosensitization is possible). Bibliographical data. Chapter II-6: CdSe electrodeposits on porous and non-porous anodized TiO2. Characterization of TiO2/CdSe photoelectrodes with solid state techniques, (photo)voltammetry and photocurrent spectroscopy. Chapter II-7: Characterization of porous-TiO2/CdSe//SPS photoelectrodes with the methods of Open Circuit Voltage Decay (OCVD) and Electrochemical Impedance Spectroscopy (EIS – Mott-Schottky). The experimental work of Part A includes a photovoltammetric study of the influence of various electrolytes on the CdSe surface properties (energy band edges), as well as a photocorrosion study, implemented by photocurrent chronoamperometry and solid state characterization methods, emphasizing on the impact of adding a ZnSe “window layer” on CdSe. Furthermore, electrodeposits of the ternary ZnxCd1-xSe compound were examined with the methods of photocurrent spectroscopy and XRD, to relate its energy bandgap with the Zn concentration x and the electrodeposition potential. The experimental work of Part B regards CdSe electrodeposits on two different structures of anodized titanium (titanium oxide) substrates: Porous (nanotube-like) and non-porous. The preparation of photoactive TiO2/CdSe electrodes was shown to be feasible in both cases, but with a strong influence of the substrate morphology and microstructure on the photoelectrochemical properties of CdSe. Best photovoltammetric results were obtained for TiO2 templates having a homogenous, well-oriented porous structure. CdSe electrodeposits on these substrates were studied with the methods of Open Circuit Voltage Decay (OCVD) and Electrochemical Impedance Spectroscopy (EIS – Mott-Schottky analysis). The most important results and conclusions of the Thesis can be summarized within the following 10 points: 1. All solutions used in liquid junctions with CdSe were characterized by linear sweep voltammetry (working electrode: Pt). The redox potential VR/O was calculated and the thermodynamic reversibility was tested in each case. The solutions FFC and ferrocene-ferricenium (Fc0/+) in an organic solvent (acetonitrile), were shown to have the highest reversibility. 2. CdSe electrodeposits on Ni or Ti were used as photoactive electrodes in a PEC and characterized with the method of (photo)voltammetry. Liquid junctions with redox and non-redox electrolytes were formed and the superficial CdSe band edges (ECB, EVB) were determined in each case, based on the “photocurrent onset” technique. At the same time this technique gives a good estimation of the flat band potential VFB and thus the maximum possible theoretical band bending i.e. the difference between VFB and VR/O. The largest theoretical band bending was found to be 1.0 V for the ferro-ferri-cyanide redox electrolyte (FFC). Apart from the above calculations, it was observed that the superficial band edges of CdSe move to more negative energy values (more positive potentials), as the electrode surface is kept in contact with any solution. This phenomenon was attributed to surface states that act as hole – traps, leading to the gradual positive charging of the surface. 3. The liquid junctions of CdSe in contact with the sulfide-polysulfide (CdSe//SPS) and the ferro-ferri-cyanide (CdSe//FFC) redox electrolytes were tested with photovoltammetric measurements, at different illumination intensities. From the derived VOC vs. lnISC linear diagrams, the “ideality factor” parameter was calculated, in respect with the “non-ideal junction” model. The lower ideality factors (between 2.6 and 3.0) and the linear dependence between ISC and light intensity (Ee), for the CdSe//SPS junction, compared with the high ideality factor values (between 5.0 and 5.3) and the sub-linear ISC – Ee diagrams (for Ee > 100 mW/cm2), for the CdSe//FFC junctions, show that the CdSe//SPS system is much closer to the ideal behavior. Though, both junctions are highly non-ideal, since the ideal case corresponds to an ideality factor of 1. 4. The electrodeposition of a ZnSe “window-layer” on CdSe has a stabilizing effect against photocorrosion, as shown by photocurrent chronoamperometry. From the systems CdSe//SPS, CdSe//FFC, CdSe/ZnSe//SPS and CdSe/ZnSe//FFC, the bilayer in contact with the sulfide-polysulfide redox solution CdSe/ZnSe//SPS was found to be the most stable photoelectrode i.e. with the smallest photocurrent decrease. Though, even in this case the phenomenon of photocorrosion cannot be fully stopped. SEM – EDAX analysis on the corroded CdSe/ZnSe//SPS samples, showed photocorrosion byproducts (CdS) and pore formation. 5. Of special interest was the complex superficial microchemical alteration, caused by photocorrosion of single (CdSe) and bi-layer CdSe/ZnSe photoelectrodes, during photocurrent chronoamperometry experiments, in contact with a ferro-ferri-cyanide redox electrolyte (FFC). It was found that the electrode modification is completed in three phases: Surface passivation, electrochemical dissolution of the passive layer, with parallel byproduct formation and complete distraction of the CdSe layer. The study on the experimental conditions has shown that photocorrosion evolves in a milder way for more alkaline FFC solutions, inert argon atmosphere over the solution and electrode rotation [1]. 6. Proper application of photocurrent spectroscopy was attempted on CdSe//SPS samples, with all necessary corrections made for spectral intensity variation with photon energy and the photocurrent change with time, due to photocorrosion. The method was then applied on ternary ZnxCd1–xSe electrodeposits in contact with the SPS electrolyte. The energy bandgap of the samples was measured for various Zn concentrations x (x calculation from XRD peak shift), which were regulated by the applied electrodeposition potential. It was found that the relation between bandgap energy and composition x, is nonlinear, in agreement with certain semiempirical models [2]. 7. Potentiostatic anodization of Ti samples in a 1M sulfuric acid solution, led to the formation of a non-stichiometric, non-porous titanium oxide (TiOx) barrier layer on their surface (passivation). CdSe was electrodeposited on the anodized samples to form Ti/TiOx/CdSe photoelectrodes in a PEC. The photocurrent of the PEC was enhanced when the substrate’s oxide layer thickness (and thus the series ohmic resistance) was reduced, by shortening the anodization time to approx. 15 min. By controlling the anodization potential the thin oxide layer thickness could be controlled even more precisely, which was found to have a regulatory impact on the CdSe crystal size (measured by XRD). Ti/TiOx/CdSe//SPS photoelectrodes had comparable photoconversion efficiencies with CdSe electrodeposits on metallic Ti, but a shorter energy bandgap, as the photon absorption edge (measured by photocurrent spectroscopy), was shifted to lower energies by 0.1 eV [3]. 8. Potentiostatic anodization of Ti samples in a mixed-oxide solution of phosphoric and hydrofluoric acid, led to the formation of a superficial oxide layer with a highly organized, uniform porous structure (Por-TiO2). The pore diameter was mono-dispersed with a magnitude of 100 nm. Potentiostatic CdSe electrodeposition on the anodized samples led to a very thin, epitaxial electrodeposit of an oriented, hexagonal structure, when using very short deposition times (1 s or less), or an oriented cubic, sphalerite type, deposit for longer times (the hexagonal phase was still observed). The same results were obtained by applying pulsed potential electrodeposition. The photoelectrochemical characterization of the Por-TiO2/CdSe samples, in contact with a SPS electrolyte, showed that TiO2 was photosensitized by CdSe. Specifically, the open circuit potential VOC was found to be enhanced by 100 mV, compared with CdSe deposits on metallic Ti, while the photocurrent increased when the samples were prepared by pulsed deposition, probably due to a better pore filling [3]. 9. The lifetime τ of photo-induced current carriers in the prepared photoelectrodes, was determined by Open Circuit Voltage Decay (OCVD) measurements (i.e. lifetime τ is calculated from the VOC decay with time, when illumination is interrupted). It was found that free carriers have slightly higher lifetimes in CdSe deposits on Por-TiO2 substrates, than on Ti. This finding was explained as a result of a higher interface area between the substrate and the CdSe layer in the first samples, thus allowing a faster electron transition to the back-contact (better electron – hole separation). In agreement with the latter explanation, the lifetime raised even more for pulsed potential CdSe deposits, which have a better pore-filling. Though, lifetime enhancement due to the porous substrate and pulsed CdSe deposition, can only be observed for low illumination intensities (i.e. low VOC values). For higher illumination intensities, the role of surface states close to the conduction band edge, seem to be playing a major role in electron – hole recombination (i.e. the CdSe//solution interface becomes more important, than the substrate/CdSe interface). 10. Por-TiO2/CdSe//electrolyte photoelectrodes were examined with the method of Electrochemical Impedance Spectroscopy (EIS). A declination of the obtained 1/C2 vs. V diagrams from the ideal linear Mott–Schottky behavior was observed. The phenomenon was found to be dependent on experimental conditions, like the semiconductor microstructure (sample annealing), the electrolyte (redox and non-redox electrolytes), illumination and the impedance measurement parameters (frequency and voltage step). A characteristic hump formation, for the diagrams obtained under intense photocorrosion conditions (non-redox electrolyte and illumination), was found to be caused by the dielectric Se layer formation on the electrode surface. With the application of a special calculation method, that takes into account the phenomenon of dielectric relaxation (i.e. dielectric constant variation with frequency), the donor concentration of the CdSe electrodeposits was also estimated.

Degree

thesis:*
Grantor dc:publisher
National Technical University of Athens (NTUA)
Year dc:date
2012

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Karousos, Dionysios
  • Καρούσος, Διονύσιος

Subjects

dc:subject × 16

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/27480

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Karousos, Dionysios; Καρούσος, Διονύσιος. Φωτοηλεκτροχημεία ηλεκτροαποθεμάτων Cd(Zn)Se: παρασκευή και χαρακτηρισμός φωτο-ηλεκτροδίων TiO2/CdSe. National Technical University of Athens (NTUA), 2012. http://hdl.handle.net/10442/hedi/27480