Back to search

National Technical University of Athens (NTUA)

Σύνθεση και χαρακτηρισμός μαγνητικών μέσων εγγραφής νέας γενιάς

Abstract

dc:description

CoPt and FePt ordered L10 (tetragonal FCT) phase alloys, in the form of thin films, have been extensively studied as candidates for ultra high-density magnetic recording media due to their high magnetocrystalline anisotropy (at least 20 times higher than that of the currently used CoPtCrX alloys). The purpose of the present PhD thesis was to contribute to the ongoing research, for the production of thin films which are based on CoPt or FePt and should be suitable for ultra high-density magnetic recording. In other studies, it has been found that by proper adjustment of the preparation conditions and the use of non-magnetic additives and/or underlayers, the desired properties of the produced films – such as perpendicular anisotropy, smaller grain size, reduction of the interaction between grains – can be enhanced. In the present thesis, the films were initially deposited by magnetron sputtering at ambient temperature with Ag or Cu as non-magnetic additives and then annealed at temperatures in the range 500oC – 600oC for annealing times in the range 5 min – 40 min, in order to produce CoPt or FePt based films with one or more of the desired characteristics. The produced and studied samples can be divided in three main categories. The first category includes post-annealed Ag/CoPt bilayers and multilayers, that were grown on Si(001) substrates. The measurements show that Ag underlayers can promote (001) texture and perpendicular magnetic anisotropy in the post-annealed Ag/CoPt bilayers. Films without Ag underlayers exhibit a (111) texture. Thin Ag underlayers (tAg≈1.2–1.8 nm) are found to promote a strong (001) texture for CoPt thickness up to 50 nm, which gradually evolves to (111) above 100 nm. A comparison of the evolvement of the coercivity Hc, the relative remnant magnetizartion Mr/Ms and the X-rays intensity ratios I001/I002 (measure of chemical ordering in CoPt) and I002/I111 (measure of crystallographic texture), as the thickness of the Ag or CoPt layer increases, suggests that there is correlation between L10 formation and development of (001) texture. The correlation is probably a result of the reduction of total strain during the annealing process, and the accompanied reduction of the lattice mismatch with the Ag underlayer. This correlation mechanism is consistent with the HIRBS measurements, which show a very strong tendency of Ag underlayer to remain near film-Si(001) interface during annealing, and the reported in bibliography tendency of Ag grown on Si(001) to adopt a (001) texture for tAg<2 nm. Comparison of crystallographic texture between post-annealed Ag/CoPt bilayers and multilayers, shows that in the case of post-annealed multilayers the (001) texture starts to degrade for lower total film thickness compared to the case of bilayers. This difference can be explained by the structural incoherence in the growth of the CoPt grains, imposed by the presence of intermediate spacer layers (which contain Ag) – as shown by the performed HIRBS measurements – during the annealing process of multilayers. The second category includes post-annealed Cu/CoPt bilayers, that were grown on Si(001) substrates. The measurements show that Cu underlayers can have as an effect the reduction of the annealing temperature that is required for the formation of the L10 phase of CoPt. The deposition of a thin Cu underlayer during sputtering (tCu≈1.2–2.4 nm) was found to promote a high degree of chemical ordering in CoPt for post-annealed CoPt films with CoPt thickness up to 50 nm. Comparison of Hc and Mr/Ms for various thicknesses of CoPt indicates that the transformation to the ordered L10 phase occurs more easily (lower activation energy) in samples with thicker CoPt layer, irrespectively of the amount of Cu underlayer. Also the magnetic and crystallographic measurements show that the Cu underlayer motivates the suppression of the activation energy (and therefore of the annealing temperature) for the formation of the L10 phase of CoPt, through the diffusion of Cu atoms into the CoPt film and subsequent formation of a ternary Cu-Co-Pt alloy. The grains in this alloy tend to adopt a random orientation. The third category includes post-annealed FePt monolayers, Cu/FePt bilayers and Ag/FePt bilayers grown on thermally oxidized Si (in short SiO). The addition of Cu underlayer during sputtering enhances coercivity Hc by about 10% for the post-annealed Cu/FePt bilayers, in comparison to the post-annealed monolayers. The relative remnant magnetization Mr/Ms is not affected significantly by the addition of Cu. The addition of Ag underlayer during sputtering enhances coercivity Hc by about 50% for the post-annealed Ag/FePt bilayers, if the thickness of the initial Ag layer is about 5% of the total film thickness, while for thicker initial Ag layer coercivity Hc is reduced. This behavior is in agreement with the hypothesis that – only for a small amount of Ag – the defused Ag atoms remain in regions between FePt grains, and therefore contribute in grain isolation and subsequently in coercivity Hc enhancement. Crystallographic texture is not significantly affected by Ag additive, in the case of SiO substrates.

Degree

thesis:*
Grantor dc:publisher
National Technical University of Athens (NTUA)
Year dc:date
2011

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Manios, Efthymios
  • Μάνιος, Ευθύμιος

Subjects

dc:subject × 20

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/27782

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Manios, Efthymios; Μάνιος, Ευθύμιος. Σύνθεση και χαρακτηρισμός μαγνητικών μέσων εγγραφής νέας γενιάς. National Technical University of Athens (NTUA), 2011. http://hdl.handle.net/10442/hedi/27782