Back to search

National Technical University of Athens (NTUA)

Ανάπτυξη και εφαρμογή μεθόδων αντιδιαβρωτικής προστασίας κραμάτων αλουμινίου φιλικών προς το περιβάλλον

Abstract

dc:description

In this PhD thesis we develop innovative, environmentally friendly, corrosion protective coatings for Al and Al alloys. We focus on conversion coatings based on the intrinsically conductive polymer of polypyrrole (PPY), as well as on coatings based on silanes, Ti and Zr oxides. Corrosion performance testing of Al surfaces prepared by these coatings confirm the compatibility with the paint /finish PPY-based coatings were deposited onto the Al surface by means of in-situ polymerization methodology. At the optimized process conditions dense and uniform conversion coatings were delivered, as examined by means of Fourier-Transformed Infra-Red Spectroscopy (FTIT) and X-Rays Photoelectron Spectroscopy (XPX) (No Al peaks at the as-deposited specimens). Our coatings passed corrosion testing, thus proposing a rather promising method for the corrosion protection of Al and Al alloys. Our approach employs aqueous solutions, does not make use of hexavalent Cr and necessitate less water supply and energy, and thus is economically favored, compared to the conventional industrial method of chromating. However, the short pot life of the PPY solution hinders the large scale continuous production applicability, even though the final corrosion protection performance of PPY-based coatings is comparable to that of chromating. Based on the promising results of the PPY-based coatings we exploited PPY as a pigment towards a novel primer formulation. PPY load up to 3%wt in alkydic resin improves the corrosion protection performance of Al alloys, compared to ZnCrO4 pigmented resin. Electrochemical corrosion testing shifts the open circuit potential of the coated Al electrodes, indicating that PPY is electrochemically active within the resin matrix. Corrosion protection of Al alloys, Al 5005 in particular, was also pursued using silane-based coatings deposited via sol-gel method. First we tested the following formulation of silanes: Dynasylan SIVO 110, Dynasylan SIVO 111 and Synasylan SIVO 113. Corrosion current density (icorr) from Tafel polarization curves was 11-fold smaller compared to the reference specimen. Scanning Electron Microscopy (SEM) imaging of these samples indicate a thin, dense layer. X-ray Fluorescence (XRF) confirmed high Si concentration, while FTIR analysis shown the presence of Al–O–Si and Si–O–Si bonds on the metal surface. The formulation that consisted from Dynasylan SIVO 110 and Dynasylan SIVO 112 attained a 13-fold smaller icorr compared to the reference specimen. From anticorrosion perspective this result is rather satisfactory. Water contact angle measurements show an increase in the hydrophobicity of these coating, which is consistent with improved corrosion protection performance in aqueous corrosive environments. Formulations based on Zr compounds exhibited lower icorr compared to the reference specimen. SEM imaging reveal the formation of dendrite-like structures, that were grown throughout the coating, while the coating thickness in-between the dendrites is about 2-3 nm. The increased content of Zr, Si, O and Al on the dendrites compared to the background, along with FTIR analysis indicate the formation of Si-O-Si, Zr-O-Al and Si-O-Zr bonds. It was found that heating to a temperature of 200 oC is more appropriate compared to heating at 250 oC and 300 oC. We also explained the role of the pH of the solutions on the layer formation and on their micro-structure in particular. For the acidic hydrolysis low pH=1,1 is required, followed by neutralization. Formulations based on Zr and Ti compounds were also used for the corrosion protection of Al alloys. These coatings were deposited using industrial processing tooling in a Al surface preparation and powder coating unit. These specimens undergone chemical, electrochemical and mechnanical testing. Sea-side class corrosion protection performance was obtained from immersion corrosion testing. Painted (via powder coating) specimens were also passed a 1000 h salt spray test without blister formation. Icorr from Tafel polarization curves was also less compared to the reference specimens. Additional testing of the powder coated samples as per QUALICOAT specifications exhibited the following results: Coating thickness more than 100 μm (QUALICOAT min thickness is 60 nm). Gloss measurement: category 3 (glossy) Mechanical testing: Cup testing: Pass (no crack formation, detachment, delamination) Cross-cute testing: Gt=0 Impact testing: Max impact energy with no tears or detachments = 7,1 Nm (QUALICOAT min energy is 2,5 Nm). We didn’t find cracks and detachments in the curved surface when we run the flexibility test in a cylindrical shaft, something that leeds to the conclusion that specimens are accepted on the basis QUALICOAT specification. The hardness test with a groove according to Buchholz, showed that the average measured values for hardness is about 110 (the QUALICOAT limit is 80). Energy dispersive X-ray spectroscopy (EDAX) along with X-ray Diffraction (XRD) analysis reveals the presence of Ti oxides, at which we merely attribute the enhanced corrosion protection performance of our coatings. Ti-Zr based coating provide corrosion protection comparable to that of chromating, that is the standard conventional methodology. The merits/advantages of our approach are (i) Enviromental: absence of hexavalent Cr (ii) Economic: less needed baths/steps, and reduced water and energy supply.

Degree

thesis:*
Grantor dc:publisher
National Technical University of Athens (NTUA)
Year dc:date
2012

Author and committee

dc:creator, dc:contributor.*
Author dc:creator
  • Δεπούντης, Σπυρίδων

Subjects

dc:subject × 19

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/27886

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Δεπούντης, Σπυρίδων. Ανάπτυξη και εφαρμογή μεθόδων αντιδιαβρωτικής προστασίας κραμάτων αλουμινίου φιλικών προς το περιβάλλον. National Technical University of Athens (NTUA), 2012. http://hdl.handle.net/10442/hedi/27886