Aristotle University Of Thessaloniki (AUTH)
Έρευνα της μη-γραμμικής συμπεριφοράς δι-χαλύβδινων σύμμικτων τοιχωμάτων υπό εναλλασσόμενη φόρτιση
Abstract
dc:descriptionIn this Thesis, the behaviour of an innovative structural element, the composite steel-concrete-steel (SCS) wall, is investigated. The objective of the research was to evaluate basic parameters of its response, such as the influence of the steel thickness, the slenderness, the curve of response, the capacity under both compressive and bending conditions, the ductility and its failure modes. For this reason, eight (8) numerical non-linear analysis models were created, five (5) of them with increasing steel thickness from 4 to 8 mm and three (3) with increasing slenderness ratio. The geometry of these models was selected on the basis of comparing them with other similar specimens in the literature and revealing the governing flexural behaviour, as well as not hindering the possibility of future test experiments. For the finite element formulation of the numerical models, the simulation environment of ANSYS v14.0 was used. Walls were assumed as fully fixed at the bottom, generating a vertical cantilever, with a fully joined contact interface between the materials, under both monotonic and cyclic horizontal loading. Next, the ultimate compression load for distinct numerical specimens was estimated and the application of horizontal load simultaneously with escalating fractions of this ultimate load was followed.The results unveiled useful aspects of the behaviour of SCS composite walls. Specifically, four distinct stages of behaviour could be observed from the force-displacement curve and the induction of the reduction factor ‘ω’ were proposed to account, primarily, for concrete cracking. The respective capacity of the specimens under monotonic and cyclic loading highly converge, in contrast to the ductility ratio “μΔ”. Moreover, through the analysis, the flexural and shear behaviour of the wall was shown, while the results exhibit good convergence with the theoretical model, based on the plastic moment capacity, shifted by a factor “s”. Furthermore, the failure mode of the specimens was mainly the concrete crushing at the wall’s bottom, causing swelling, and the steel plate local buckling at the edge, which was in agreement with failure modes extracted from related test results. In parallel with the above, the simultaneous application of horizontal and compression loads illustrated that it is possible to stipulate bending-compression capacity curves, since there was close proximity between the results and high convergence with related numerical results by other researchers. From this curve, a rapid decline of the bending moment capacity was apparent when the respective compression load was around 0.5 times the ultimate compression load of the section; which can be considered as a compression load limit for this kind of walls. Finally, due to the shape of the failure mode, a research, based on buckling analysis features, was conducted to numerical short-scale models of steel plates and useful curves of their behaviour were extracted.It must be pointed out that there are few references or guidance in the relevant codes for their design parameters and the current study offers important information about their behaviour.
Degree
thesis:*- Grantor dc:publisher
- Aristotle University Of Thessaloniki (AUTH)
- Year dc:date
- 2015
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Vazouras, Konstantinos
- Βαζούρας, Κωνσταντίνος
Subjects
dc:subject × 16- Σύμμικτες κατασκευές
- Σύμμικτα τοιχώματα
- Διχαλύβδινα τοιχώματα
- Ανελαστική ανάλυση
- Εναλλασσόμενη φόρτιση
- Composite walls
- Composite structures
- Sandwich steel walls
- Shear walls
- Nonlinear analysis
- Cyclic loading
- ANSYS
- Επιστήμες Μηχανικού και Τεχνολογία
- Επιστήμη Πολιτικού Μηχανικού
- Engineering and Technology
- Civil Engineering
Rights
dc:rights- Statement dc:rights
-
- BY_NC_SA
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/35605