Back to search

University of Thessaly (UTH)

Έλεγχος της μετάβασης και αποκόλλησης οριακού στρώματος και της απόδοσης αεροτομής με ενεργητική καθοδήγηση της ροής

Abstract

dc:description

At the beginning of the 21st century, Fluid Mechanics applications are connected with every aspect of human activity. The search for more effective power generation machines, the need for faster and more distant transportations, the ambition to explore the universe, the pursuit of more massive constructions, the continuous consumption of gigantic energy quantities and the increasing demands of the defence industries are some of the most obvious examples that make the optimization of the fluid flows essential. The optimization of a flow involves theoretical studies of its characteristics, simulations and experiments. Many times, control and guidance of flows are useful methods for their optimization. This Doctoral thesis is an attempt to couple the foregoing aspects, aiming to add to the research on active flow control. This aerodynamic structure of airfoil was selected due to its wide use in numerous applications such as air-vehicles, power plants and wind turbines. For this purpose, a numerical model was used in the form of the computational aerodynamics code CAFFAeroel, which was improved to simulate several categories of airflow around an airfoil. The obtained numerical results are useful in the study of the main factors which affect the characteristics of the above air flows. The main part of this study focuses around the active control or guidance of the boundary layer. Active flow guidance came up as an idea with the widespread use of aerodynamic bodies, while interest has peaked in recent decades, and boundary layer control tends to be the main route to achieve flow optimization. Firstly, new software was developed that can construct the geometry of airfoils and was combined with a code generating curvilinear numerical grids. Subsequently, the computational aerodynamics code CAFFAeroel was extended and improved. The improvements, mainly, concerned the turbulence models, the simulation of surface roughness and the determination of flow transition from laminar to turbulent. The introduction of a new transition model and the improvement of the k-ω turbulence model constitute the first two elements of originality of this thesis. As a result, the new aerodynamic code CAFFAeroel is more accurate in simulating transitional flows, especially at low angles of attack. Furthermore, the original CAFFAeroel was appropriately modified to allow simulations of blowing and/or suction of the boundary layer. Air flow simulations around an NACA0012 airfoil were carried out, in order to assess the effect of specific factors on the flow characteristics. A detailed study was made concerning the active boundary layer control and comprehensive results are presented about the influence on the flow around the airfoil and its aerodynamic performance. The main goal was to determine the physical, operational and cost effective limits of the obtained flow optimization. The structure of this thesis was dictated by the need to sequentially study the phenomena that are associated with the flow around an airfoil. Thus, simulations are presented and conclusions are drawn concerning the effect on the point of flow transition onset of parameters such as the surface roughness, the angle of attack, the Reynolds number, the incoming turbulence intensity, and the blowing or suction of the boundary layer. The simulation results help to draw conclusions and to explain the effect of these parameters on the flow characteristics and the aerodynamic performance of the airfoil. From the results of the present study which are compared with experimental measurements and other similar numerical results, the following main conclusions are drawn: Regarding flow transition, the roughness of the airfoil affects significantly the transition phenomenon. Surfaces with higher roughness cause an upstream movement of the point of flow transition. However, there is a saturation point, beyond which any further increase of the roughness height cannot change the position of the transition point. The closer to the airfoil leading edge the roughness area is located, the more upstream moves the transition point. This movement is also proportional to the width of the roughness area. For a series of sequential roughness areas, the greatest influence is caused by the first roughness strip, its width and height being crucial. A roughness area does not change the position of the transition point, if it is located downstream from it. Higher free stream turbulence moves the point of transition upstream. The angle of attack is the most important factor, moving the transition point upstream towards the leading edge (LE) for larger angles of attack. Increasing the Reynolds number of the incident flow, results to analogous upstream movement at a given angle of attack. Suction of fluid from the boundary layer near the wall can delay flow transition. More intense suction may bring further delay of the transition, while a widening of the suction area has an analogous effect. The most effective location for suction lies just downstream of the point of the expected transition onset. Similarly, blowing fluid into the boundary layer causes a delay of transition. An increase of the injected fluid flow rate and a decrease of the injection angle, with respect to the airfoil surface, can delay flow transition. The optimal application area for blowing is located just upstream from the estimated point of transition onset. Again, multipoint blowing from several successive slots is more effective than blowing through a single slot. Regarding the aerodynamic performance of the airfoil, the following main conclusions may be drawn: Airfoils with higher roughness produce increase drag and reduce lift, thus, leading to reduced aerodynamic performance, because boundary layer separation occurs at lower angles of attack and nearer to the trailing edge. These effects become more intense when the roughness area starts closer to the trailing edge. The width of a rough area is an important factor which provokes earlier boundary layer separation, when increased. However the roughness height remains the most important parameter. A roughness strip located near the trailing edge helps the flow to remain attached to the surface. This is mainly due to the local production of turbulence, which enforces the boundary layer with higher momentum from the outer layers of the flow. Roughness strips that cover a part of the airfoil surface, followed by intermediate smooth parts, have a weaker effect on the aerodynamic performance of the airfoil, than a continuous strip, over the same total width. Comparing two cases of roughness strips in array, over the same width along the airfoil, the more effective is the array with the denser distribution of strips. The roughness height of the first strip is a dominant factor, because it is the first one encountered by the fluid. Increased free-stream turbulence causes a drop of the aerodynamic performance of the airfoil. This is due to the perturbations of the main flow, making the boundary layer more unstable and prone to turbulent separation. Active flow control through suction of fluid from the boundary layer can improve the ratio of lift-to-drag of the airfoil. As the suction point moves downstream from the leading edge, it decreases the pressure on the upper airfoil surface, near the minimum pressure point, until saturation takes place. The optimum position for the suction slot is located at a distance from 5% to 15% of the chord length. The angle of attack for maximum lift is increased in the presence of suction, while the aerodynamic performance of the airfoil is improved more when an increased suction intensity is applied or when suction is made through a series of slots (multipoint suction). Blowing into the boundary layer can also enhance the performance of an airfoil by helping the fluid follow a smoother path. The optimum blowing position is found to be at a distance from 75% to 85% of the chord length, while the optimum blowing is in the direction of the main flow/airfoil surface. Increasing the blowing intensity (at the optimum location) improves the lift and slightly the drag, thus, leading to a better airfoil aerodynamic performance. Increased blowing intensity significantly delays the flow detachment near the trailing edge, without increasing the angle of attack for maximum lift. Blowing through an array of slots produces better results with lower total blowing intensity (i.e. cost effective), and increases the angle of attack for maximum lift. Finally, as future prospects of furthering the present research, the following are proposed: a) Introduction of the k-ω SST turbulence model into the CAFFAeroel code in order to improve the simulation of separated flows, b) Converting the code to three-dimensional, in order to include diffusion/interaction phenomena in the third direction, c) Study of flow control through blowing/suction in combination with lift-enhancing devices (e.g. flaps, slats), d) Simulation of unsteady blowing/suction, and e) Study of blowing/suction in the presence of heat transfer

Degree

thesis:*
Grantor dc:publisher
University of Thessaly (UTH)
Year dc:date
2016

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Kapsalis, Panagiotis-Chrysovalantis
  • Καψάλης, Παναγιώτης-Χρυσοβαλάντης

Subjects

dc:subject × 12

Rights

dc:rights
Statement dc:rights
  • BY
Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/37397

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Kapsalis, Panagiotis-Chrysovalantis; Καψάλης, Παναγιώτης-Χρυσοβαλάντης. Έλεγχος της μετάβασης και αποκόλλησης οριακού στρώματος και της απόδοσης αεροτομής με ενεργητική καθοδήγηση της ροής. University of Thessaly (UTH), 2016. http://hdl.handle.net/10442/hedi/37397