Back to search

Democritus University of Thrace (DUTH)

Συμπεριφορά στοιχείων σκυροδέματος ενισχυμένων με ελάσματα συνθετικού οπλισμού

Abstract

dc:description

Externally bonded fiber reinforced polymers (FRP) are very popular in retrofit of reinforced concrete beams. They have high strength to weight ratio and geometric versatility while up to date research, has confirmed the upgraded response of carbon FRP (CFRP) strengthened reinforced concrete beams, both in flexure and shear. Recently, considerable interest has been attracted by the fatigue behavior of reinforced concrete members, especially beams and bridge girders. Fatigue experiments are very demanding as they are time and energy consuming, require thoroughly designed experimental setup and equipment, to resist millions of cycles of loading. Therefore, the beams are usually of small scale and the studied parameters limited. The aim of the present research is the experimental investigation of the response of carbon fiber reinforced polymer (CFRP) strengthened reinforced concrete (RC) beams, of large scale, under fatigue loading. Reinforced concrete beams were cast for this purpose, both with rectangular and T cross sections, with web dimensions of 200 mm x 500 mm and 3050 mm in length. Beams were strengthened in flexure with externally bonded CFRP laminate (Externally Bonded Reinforcement, EBR) or with CFRP laminates bonded into slits on the concrete cover surface (Near Surface Mounted, NSM). Transverse CFRP sheets were placed on the shear spans of the beams to avoid fragile shear failure. All specimens were tested under fatigue loading, with load-unload cycles of 2Hz frequency. Two different amplitudes of cycles were investigated. The different fatigue life and modes of failures are discussed. Beams subjected to the low loading range, simulating the service loads of a bridge beam, could sustain more than 2 million cycles. Beams subjected to the high loading range, according to the maximum limit of the American Concrete Institute (ACI) Committee 440.2R-08, presented fatigue failure of the reinforcing steel in cycles less than 1.5 x 106. The ratio of the axial rigidity of the tensile steel bar ks to the axial rigidity of fiber reinforced polymer (FRP) strengthening kf plays a significant role in extending the fatigue life of steel and thus of RC FRP strengthened beams. The lower the ks/kf ratio, the higher the fatigue life of the retrofitted member. NSM strengthening may maintain a full bond with the concrete substrate even after the fatigue fracture of steel bars. Therefore, it may provide residual capacity to the retrofitted member to survive detrimental collapse. This research also presents an analytical study on the fatigue response of reinforced concrete beams strengthened with fiber reinforced polymers (FRP). The study gathers the experimental results from the international literature and from authors’ experiments and investigates the critical parameters that affect fatigue performance of reinforced concrete (RC) beams. The higher the maximum stress and the stress range on the longitudinal steel bars of the beam, the lower their fatigue life. ACI Committee 440.2R-08 guide recommends stress limits for FRP strengthening under tension and concrete under compression as well as a peak reinforcing bar stress of 80% of yield strength to estimate the upper limit of fatigue loading in Serviceability Limit State (SLS). It is acknowledged by the existing literature that the critical material vulnerable to fatigue failure is steel and that stresses on steel about 60% of its yielding strength practically do not lead to fatigue failure. The available fatigue prediction models provide the number of cycles to failure with respect to the steel stress range assuming indirectly a sustained load between a minimum and maximum level. Given the SLS design approach for steel stress limitation, the present research aims to introduce directly and clearly the ratio of maximum steel stress to the yielding strength of steel σmax/fy into the fatigue design. A new analytical model is proposed for predicting the fatigue life of FRP strengthened RC beams. The parameters used are the maximum stress of tensile steel (σmax) to the yielding strength (fy) ratio, as well as the axial rigidity of longitudinal steel (ks) and FRP (kf) reinforcement. The predictions of the proposed model are compared against the experimental results as well as against the predictions of fatigue models in the literature. Keywords: Fatigue, Fiber Reinforced Polymers, Laminates, NSM, Strengthening, Steel to FRP axial stiffness ratio, Analysis

Degree

thesis:*
Grantor dc:publisher
Democritus University of Thrace (DUTH)
Year dc:date
2016

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Barbara, Charalambidi
  • Χαραλαμπίδη, Βαρβάρα

Subjects

dc:subject × 14

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/38106

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Barbara, Charalambidi; Χαραλαμπίδη, Βαρβάρα. Συμπεριφορά στοιχείων σκυροδέματος ενισχυμένων με ελάσματα συνθετικού οπλισμού. Democritus University of Thrace (DUTH), 2016. http://hdl.handle.net/10442/hedi/38106