Back to search

National Technical University of Athens (NTUA)

Μεταλλικές και σύνθετες ηλεκτρολυτικές επικαλύψεις ψευδαργύρου από όξινα θειικά λουτρά

Abstract

dc:description

The aim of the present thesis was to investigate the cathodic electrodeposition of metallic zinc on low–carbon stainless steel (SS316L) electrodes, from aqueous acidic (pH 2.0–4.5) sulphate–chloride–borate baths of zinc(II) ions, under direct current (DC) and pulse direct current (PDC) plating conditions. The effect of electrolysis parameters (i.e., current density, electrolytic bath pH, pulse frequency and duty cycle) on the solid state structure (micro- and macrostructure) of the as-grown deposits was studied. The crystallographic texture of the deposits was identified by means of the Relative Texture Coefficient (RTC) assessed from X–ray diffraction analysis (XRD) data. The surface morphology was examined by typical and/or high resolution scanning electron microscopy (SEM). Mechanical properties of the deposited layers, such as surface roughness and Vickers microhardness, were measured, and their corrosion resistance was evaluated by potentiodynamic measurements and Tafel analysis. In addition, zinc matrix composite coatings containing polymethyl methacrylate (PMMA) particles were fabricated from similar Zn(ΙΙ) baths on SS316L substrates, under galvanostatic, either constant or pulse current, plating conditions. The effect of particle inclusion on the deposit electrocrystallization was investigated.The structure and morphology of metallic zinc electrodeposits prepared under DC conditions depended on the deposition current density (0.5 to 40 A dm−2) and the bath pH (2.0 to 4.5). Crystallographic analysis revealed that under low saturation conditions randomly oriented deposits were produced, whereas at higher current densities the electrodeposits mostly exhibited (00.2), (10.Χ) (Χ = 3, 4, 5) and (11.4) dominant orientations. The corrosion resistance of the as-prepared deposits depended on their crystallographic orientation and was found to increase in the order: (random orientation) < (10.X) < (11.4) < (00.2).The occurrence of well-defined XRD texture was correlated to the dominant mechanisms of nucleation and growth of the polycrystalline phase. The electrochemical nucleation and growth was studied by means of chronoamperometry at various cathodic potentials in the charge–transfer controlled regime. Analysis of the recorded potentiostatic current–time transients relied on theoretical models concerning instantaneous and/or progressive nucleation of three–dimensional (3D) growth centres having the geometry of right circular cones. Nucleation rate constants were calculated and correlated analytically with the respective potentials, using the classical theory of heterogeneous nucleation. The experimental study showed that at cathodic overpotentials less than 0.30 V (negative to the Zn2+/Zn redox value), a two–dimensional (2D) contribution, limited by the incorporation of Zn adatoms in the developing lattice, is significant at the early stages of deposition, which though rapidly degenerates to a 3D type of growth. This mixed dimensionality mechanism (2D/3D) became more progressive in type with lowering the bath pH. At cathodic overpotentials in the range 0.30 to 0.55 V, the electrodeposition proceeded by instantaneous 3D nucleation, which turned to progressive at higher overpotentials and/or very acidic baths. The application of pulse plating resulted in coatings which were microstructurally different to those prepared under comparable DC conditions. Crystallographic texture diagrams were drawn for the employed peak deposition current densities, having as coordinates the duty cycle and the pulse frequency. In the case of PDC plating from a pH 2.0 bath, the application of relatively low peak currents, 2 and 10 A dm−2 for specific pulse characteristics, resulted in a texture modification from (10.X) and (00.2) to (11.2) and (10.X), respectively. The application of PDC did not influence the texture of the 20 and 40 A dm−2 deposits, which, similar to DC plating, exhibited an intense (00.2) preferred orientation within the whole range of experimental conditions. However, PDC plating led to deposits with reduced average crystallite size, which decreased more with increasing peak current density. PDC plating from a pH 4.5 bath resulted in coatings oriented mostly with the basal (00.2) and high index (10.3), (10.4), (10.5) pyramidal planes parallel to the surface, with the size of crystallites controlled by the deposition current density. The effect of pulse current was illustrated in terms of enhanced nucleation and inhibited growth.The presence of polymeric PMMA particles in the electrolytic bath impaired the commonly obtained basal Zn(00.2) texture, in favor of prismatic and/or pyramidal orientations. The volume fraction of PMMA particles in the composite coatings was determined gravimetrically, by means of weighting and filtration techniques. The observed dependence of the PMMA content of the deposits on bath pH and applied current density was illustrated in terms of the particle surface charge variation and their interaction with the growing metal phase. The corrosion resistance of the Zn(PMMA) coatings was evaluated by Tafel analysis.

Degree

thesis:*
Grantor dc:publisher
National Technical University of Athens (NTUA)
Year dc:date
2016

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Vasilakopoulos, Dimitrios
  • Βασιλακόπουλος, Δημήτριος

Subjects

dc:subject × 29

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/39080

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Vasilakopoulos, Dimitrios; Βασιλακόπουλος, Δημήτριος. Μεταλλικές και σύνθετες ηλεκτρολυτικές επικαλύψεις ψευδαργύρου από όξινα θειικά λουτρά. National Technical University of Athens (NTUA), 2016. http://hdl.handle.net/10442/hedi/39080