National Technical University of Athens (NTUA)
Ανάπτυξη και διερεύνηση μεθόδων κατεργασίας για την ανάκτηση μετάλλων από ηλεκτρονικά απόβλητα
Abstract
dc:descriptionWaste Electrical and Electronic Equipment (WEEE) constitute a special waste category. This fact can firstly be attributed to the ever rising quantities at which they are being produced. Indeed, during the last decades the technological progress has led to advanced needs that require such devices, leading to multiplying quantities of them being put to the market. At the same time the rapid development of new technologies and applications make the upgrade or replacement of the devices inevitable after a short period of time. As a result, huge quantities of these devices end up as waste, demanding special treatment and exploitation for the recovery of materials and resources.Another characteristic of WEEE that makes them a very “attractive” stream of waste is the fact that due to their construction they contain a large amount of valuable material that demonstrate financial interest regarding their recovery. These materials are namely glass, plastics and metals. In the case of metals in particular, WEEE contain them in concentrations higher than the ones at which they can be found in natural minerals and ores.Considering all the above it can be easily apprehended that at some point WEEE started gaining attention as waste. The argumentation for their legislative determination in Europe started in the mid ’90. After years of consultation the discussions led to the publication of directives 2002/95/EC and 2002/96/EC that set the foundations for dealing with WEEE. These directives set restrictions regarding the usage of certain hazardous materials, as well as targets for their recovery and exploitation. In the following years other directives were published, complementing or recasting the aforementioned ones, always aiming however towards the same direction.Purpose of the present doctoral thesis was the investigation of three main approaches for the chemical treatment of WEEE [and specifically the printed circuit boards (PCB) from personal computers], aiming to the recovery of metals. It was towards that direction that hydrometallurgy, electrometallurgy and pyrometallurgy were studied. Firstly a pretreatment process was suggested for the PCB, in order to obtain a powder that would be suitable for further treatment. This process consisted of the mechanical cut, the thermal treatment and the pulverization of the product, so as to obtain a powder of the PCB. The respective research papers do not mention such a step, but rather treat PCB “as is”. This results in the need for multiple treatment steps. The obtained PCB powder was suggested to thorough physical and chemical characterization. This analysis confirmed the literature data, according to which PCB demonstrate high content in metals of financial interest. It was confirmed that PCB contain high concentrations of copper (20-22 % wt), which was the metal with the highest percentage. In addition aluminum, lead, tin, nickel and zinc were observed. From elemental analysis of various different parts of the PCB gold was traced to be present in the contacts of PCB.Regarding the hydrometallurgical treatment a first series of experiments was carried out regarding the dissolution of PCB powder by treatment with acids. The aim of these experiments was to draw some initial conclusions regarding the parameters affecting the dissolution process of copper, nickel and zinc. The dissolution using nitric, hydrochloric and sulfuric acid was investigated, given that they are the most commonly used acid solvents. The parameters that were studied included the acid concentration (0,5, 1, 2 and 6Μ), reaction temperature (40οC, 60οC and 90οC) and time (1-2h). Following that, a second experimental part was carried out with the application of the Taguchi method for design of experiments and statistical evaluation of experimental data. In a first stage the contribution of the Taguchi method is the determination of 16 experiments that were suggested in order to study the 5 selected parameters (type of acid, acid concentration, temperature, treatment time and stirring), at 4 levels for each one. If not for the Taguchi method, the complete study of all the possible combination would have required the prohibitive number of 45 = 1024 experiments. In addition conclusions were drawn regarding the way that each parameter affects the whole process, in both quantitative and qualitative manner. In the case of copper and nickel it was concluded that the dominant parameter of the process is the type of acid (88,48% and 67,78% respectively). Contrary to that, in the case of zinc the contribution of parameters follows a rather equal distribution and there is no prevailing one.Based on these conclusions the optimization of the whole process was possible, as well as the determination of the optimum conditions for the treatment of each of the three metals. The highest achieved concentrations at these conditions were 19,88% for copper, 1,94% for nickel and 1,65% for zinc.Having already studied and optimized the hydrometallurgical process of the PCB powder, attention was focused on the electrochemical approach. The complexity of the powder, due to its content of various metals, led to the decision for a preliminary series of experiments with synthetic solutions, in order to study the behavior of the electrochemical system. It was observed that in highly acidic environment (pH≈0) the products of electrodeposition demonstrated further dissolution and thus the study of different pH values was chosen. The experiments carried out at pH≈9 led to precipitation of the electrodeposition products. The best behavior of the solutions was finally achieved at pH≈4. Based on these conclusions a new series of experiments was carried out, this time using solutions form the dissolution of the actual PCB powder in 4M nitric, hydrochloric and sulfuric acid. The recovery of copper by electrodeposition was achieved from these solutions with electrolysis at -0,45 V, -0,35 V and -0,30 V vs. Ag/AgCl/KCl3M respectively. The obtained copper deposits featured high purity and were in granular form, allowing easy recovery.In a next step, the possibility of recovering gold that is present in the contacts of the PCB was explored. Despite its small percentage and the fact that overlap of its picks in the voltamographs with these of copper, the electrodeposition of gold was achieved with purity of almost 100%. The recovery of gold took place from solutions of dissolved PCB contacts’ powder in aqua regia, via electrolysis at 0,55 V vs. Ag/AgCl/KCl3M. Similarly to copper, the deposits of gold were in granular form allowing their easy recovery. It is worth mentioning that the recovery of both copper and gold was achieved from solutions of dissolved powder with no other prior process for the removal of other metals.In the last experimental part of the thesis a study of the pyrometallurgical treatment of the PCB powder was carried out. Pyrolysis of WEEE is a well-established industrial practice, however the chlorination of such materials has not been studied in extent. This can be attributed to the difficulty of applying such a method in laboratory scale. Two separate series of experiments were carried out aiming to the selective separation of metals, based on the volatility of chloride compounds. The first one focused on the feasibility of chlorination of the PCB powder at various temperatures, by applying gas chlorine of high purity. From the chemical analysis of the solid chlorination products it was concluded that high level of chlorination can be achieved. The chlorine content was observed to be a little higher at the solid samples obtained after treatment at 300οC, compared to the ones at 500οC and 750οC. Having achieved the chlorination of the PCB powder, a second series of experiments was carried out, this time using standard chloride compounds. The goal was to study the feasibility of their separation and selective recovery. The crucial for the whole process temperature is 500οC or 750οC. At temperatures up to 500οC the solid chloride compounds remain in solid form and the metals can be recovered via reduction with hydrogen and separation based on specific gravity. At 750οC the volatile chloride compounds in gas form are collected in solutions, from which the metals can be recovered via condensation and reduction.The originality of the present doctoral thesis consists in that:•A pretreatment process was suggested, resulting in a PCB powder which was suitable for treatment via any of the three main methods, with no further required step.•The statistical evaluation of the data regarding the hydrometallurgical treatment of the PCB powder led to qualitative and quantitative conclusions for the parameters that affect the process. Furthermore, the optimum conditions were set for the treatment of each of the studied metals.•The thorough study of the electrochemical system of the solutions of PCB powder and PCB contacts’ powder resulted in the recovery of copper and gold respectively, without any prior treatment for the removal of other metals•The chlorination process for the treatment of the PCB powder was studied, along with the parameters affecting it.
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2017
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Masavetas, Ilias
- Μασαβέτας, Ηλίας
Subjects
dc:subject × 10Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/39924