University of Patras
Μελέτη των συνθηκών ψύξης πτερυγίων στροβίλου μέσω έγχυσης ψυχρού αέρα στην ζώνη ανακυκλοφορίας της πεταλοειδούς δίνης στην κόγχη σύνδεσης του πτερυγίου με τα πλαϊνά τοιχώματα του στροβίλου
Abstract
dc:descriptionThe thermodynamic analysis of the Brayton cycle designates that the thermal efficiency and the specific work output of a Gas Turbine can be improved by increasing the Turbine Inlet Temperatures. Furthermore, increment of the turbine inlet temperatures also results into lower fuel consumption rates, while, if the gas turbine is meant for propulsion purposes, increment of the turbine inlet temperatures also results into increased engine thrust. Unfortunately, these high gas temperatures jeopardize the integrity of the high pressure turbine components and more particular, the turbine blades and the endwall on which the blades are attached. In modern turbines, the turbine inlet temperature may reach the level of 1900K, exceeding by far the melting temperature of the metal walls. As a result, the turbine components operate at much harsher environments than in the past. Maintaining adequate life in these high temperatures requires the development of new materials and manufacturing processes, as well as efficient cooling methods for the components of the turbine.In order to address and avoid the failure of the blades and endwall of a turbine cascade, the method of "film cooling" has been incorporated as part of the components design process. In the latter method, air is bled from the compressor stage, passed through internal chambers of the engine to the turbine components and is injected through discrete holes in the walls of the blades and the endwall, forming a thin protective layer film between the hot combustion gases and the metal surfaces of the parts.A critical region that is subjected into increased thermal stresses is the area around the leading edge - endwall juncture, which is inherently dominated by the presence of strong three dimensional secondary flows (also known as juncture flows) responsible for the increment of the local heat transfer rates to the order of 350%. Moreover, these flows, prevent the penetration of the fluid in the problematic area, displacing the coolant mass flux away from the surface of the endwall before providing adequate cooling.The subject of the current thesis, is the design, development and testing (both experimental and computational) of a prototype cooling scheme (with the method of film cooling), in order to effectively address the endwall overheating problem around the leading edge - endwall juncture, especially around the stagnation plane area. The main feature of the novel injection method is that the coolant air is ejected in such a way that the cooling effectiveness in the area is assisted by the rotational sense of local three-dimensional flows.The complexity of film cooling for the problematic area arises from two facts. Firstly, as mentioned previously the flow around the leading edge junction is characterized by complex three dimensional flows. Secondly, the problem is characterized by three temperatures: the temperature of the main flow, the endwall temperature and the temperature of the coolant air. In order to fully investigate the features and characteristics of the proposed cooling method, the work of the current thesis includes both, an experimental and a computational part: Computational part:The successful design of a possible cooling scheme for the particular region of the endwall requires the knowledge and understanding of local flow in which the coolant jet is to be entrained. Furthermore, it is important to understand the expected interaction between the coolant air and the local three-dimensional flow. For this purpose, the method of Computational Fluid Dynamics was employed for predicting the relevant three-dimensional flow field around the blade-endwall junction area. Simulations were made for both, the basic geometry in the absence of any coolant injection (which were used as a reference point) and simulations during the employment of the proposed coolant injection method which concerned the effect of various parameters on the cooling efficiency of the problematic area. For the simulations, the following temperature step was adopted: Warm endwall - Warmer main flow (mainstream) - Cold air injection, which is similar to that seen in real applications. The CFD predictions were very helpful towards understanding the relevant flow field in the junction area, both qualitatively and quantitatively in terms of the relative magnitudes of the flow structures and the aerodynamic characteristics of the flow in the region.Experimental part:For the experimental investigation regarding the effectiveness of the proposed cooling method, a new experimental technique was employed which was developed as part of the current thesis. In the latter technique, a reversed temperature step is adopted (when compared to the relevant temperature step adopted for the numerical simulations), e.g. Cold main flow (mainstream) - Warm endwall - Warmer air injection. Along with the use of infrared thermography, the endwall film cooling effectiveness is quantified and the region that the injection is effective is determined.In addition to the qualitative and quantitative evaluation of the cooling effectiveness, extensive aerodynamic measurements were necessary in order to evaluate the aerodynamic costs of the proposed cooling method. These measurements provide an indication of whether the cooling process affects the growth and intensity of secondary flows (e.g. passage vortex) in the region downstream of the coolant jet-local three-dimensional flow interaction.
Degree
thesis:*- Grantor dc:publisher
- University of Patras
- Year dc:date
- 2015
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Milidonis, Kypros
- Μηλιδόνης, Κύπρος
Subjects
dc:subject × 16- Στροβιλοκινητήρες
- Ψύξη πτερυγώσεων στροβίλου
- Δευτερογενείς ροές
- Μετάδοση θερμότητας
- Πεταλοειδής δίνη
- Ροές σύνδεσης πτερυγίου δαπέδου
- Turbomachinery
- Turbine endwall film cooling
- Secontary flows
- Heat transfer
- Horseshoe vortex
- Blade-endwall junction flows
- Επιστήμες Μηχανικού και Τεχνολογία
- Επιστήμη Μηχανολόγου Μηχανικού
- Engineering and Technology
- Mechanical Engineering
Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/39941