University of Patras
Παραγωγή τσιμέντων μπελιτικού τύπου με παράλληλη αξιοποίηση βιομηχανικών παραπροϊόντων
Abstract
dc:descriptionContemporary cement industries are faced with two main challenges: the reduction of CO2 emissions released during cement production as well as the cost and sustainability of raw materials and fuel. Cement industries rank second position in CO2 emissions produced by industrial activities (26%) and participate by 5-8% to the total anthropogenic CO2 emissions. During cement production CO2 emissions are primarily attributable to the decomposition of calcium carbonate (fundamental reaction for the cement production), the use of fuel and to a less important extent to the use of electricity and transportation. In this thesis, the production and development of belite type cements with parallel valorization of industrial by-products as raw materials, was investigated aiming at minimize the aforementioned problems. The difference between belite and Portland cements, is in the reduced levels of the tricalcium silicate (C3S) phase and the corresponding increase of dicalcium silicate (C2S) content. The result of this modification is the reduction of CaCO3 demand and of the firing temperature (~1350°C), both leading to the reduction of CO2 emissions. The main drawback of belite type cements are the low early compressive strength development. Several solutions have been proposed in order to overcome the low early strength, such as the stabilization of active belite polymorphs (α, α’H, α’L, β) through rapid cooling of the clinker or/and the introduction of 'foreign' ions (B2O3, Na2O, K2O, BaO, MnO2, Cr2O3) in the belite crystals. Alternatively the presence of a hydraulic compound, Klein phase (4CaO·3Al2O3·SO3/C4A3Ŝ), is expected to provide the required early strength. First, the influence of the firing temperature and cooling rate on the microstructure development and the physical/mechanical properties of belite type clinker BC (C2S=55% w.t. estimation from Bogue equations) was investigated. In order to study the effect of firing temperature on the microstructure development of clinker BC, clinker fired at four temperatures (1340°C, 1360°C, 1380°C and 1400°C). Two cooling methods of the clinker were applied: a) rapid cooling, achieved by crushing, suppling air at the same time (uf.c.≈1°C/s), and b) slow cooling to ambient temperature (us.c.≈0.1°C/s). The results of optical microscopy, of the produced clinkers, showed that increase of firing temperature and the reduction of cooling rate resulted in the increase of the belite crystal size. Semi-quantitative mineralogical analysis, according to the Rietveld method, showed that the reduction of the cooling rate lead to clinker with higher belite content and to the simultaneous increase of beta (β-) and gamma (γ-) polymorph (low or no hydraulic properties). Upon rapid cooling, despit the fact that belite content decreased in comparison with slow cooling, the a'L- polymorph content of belite is increased. The required grinding time for the clinker to achieve a particular values of the specific surface area (4000 cm2/g), was less on slow cooled clinker due to the presence of gamma polymorph of belite. Compressive strength test were done for the fast cooled cement, and showed that the early days strength development decreased in comparison with OPC (Ordinary Portland Cement), as anticipated for belite type cements. For the 28 days of hydration the compressive strength results for BCf.c._1340oC, BCf.c._1360oC, BCf.c._1380oC και BCf.c._1400oC were 52.9 MPa, 57.4 MPa, 50.7 MPa and 50.9 MPa respectively, comparable with OPC CEMI 32.5N (32.5 MPa up to 52.5 MPa) according to EN 197-1. As a solution to the problem of low early compressive strength of belite cements, the effect of boron oxide addition in the belite crystal (as part of the clinker) for the stabilization of the most active polymorphs was investigated. Three types of clinker were produced, two with boron by-product addition (DBW, Kirka Boron Works) 1% w.t (BC_BW1), 6.5% w.t. (BC_ΒW6.5), and one with the addition of 2% w.t. boric acid (BC_ΒΑ1.5), which correspond to 0.38% w.t., 2.46% w.t. and 2.46% w.t. Β2Ο3, respectively. The design of the raw meals was based on the modified Bogue equations, and the main target was the high belite content (≥59% w.t.). Based on the results of the free lime test and on the microstructure development of the clinker, the firing temperaturew were 1350οC, 1330οC and 1310οC for BC_BW1, BC_BA1.5 and BC_BW6.5 respectively. The microstructure of the produced clinkers showed that they consisted predominantly of belite crystals surrounded by a micro-crystalline matrix composed by calcium boron silicate (C5BS), tricalcium aluminate (C3A) and tetracalcium aluminoferrite (C4AF). Increase of B2O3 content in the raw meal was accompanied by the reduction of the firing temperature, the stabilization of α΄- polymorph of belite as well as the belite overgrowth from Type I to Type III (no hydraulic properties). The produced cements presented relatively low early strength development. However, for the 28 days the results were 52.7 MPa and 60.0 MPa for BC_BA1.5 and BC_BW1 respectively, similar or even improved in comparison with OPC 42.5N. The addition of 2.46% w.t. B2O3 (BC_BW6.5) resulted to the deterioration of cement’s properties (5.6 MPa at 28 days). The results suggest that controlled quantities B2O3, pure or of boron by-products origin may be used in belite type cement production improving the late strength values. Next, the optimization of the early compressive strength by the production of sulpho-belite cements and the parallel valorization of industrial by-products as raw materials was studied. The by-products used, included electric arc furnace slag ("SOVEL" steel industry), red mud ("Aluminium of Greece") desulphurization gypsum (FGD, "PPC-Hellas" Megalopolis A) and boron by-product (DBW, Kirka Boron Works). Five clinker types were produced, SBb, SBb_EAFS (10% w.t. EAFS), SBb_R.M. (5% w.t. R.M. και 14.5% w.t. FGD gypsum), SBs_R.M. (5% w.t. R.M. και 23% w.t. FGD gypsum) and SBs_R.M._DBW (5% w.t. R.M., 22% w.t. FGD gypsum and 1% w.t. DBW). The design of the raw meals was based on the modified Bogue equations and the target was the high belite content in case of SBb, SBb_EAFS and SBb_R.M. and Klein compound in case of SBs_R.M. and SBs_R.M._DBW. The firing temperature for all clinkers was 1330°C, except for SBs_E.Ι._DBW which was fired at 1310°C, due to boron by-product addition. The firing temperature was determined by preliminary firing tests in the temperature range 1280°C-1340°C, based on free lime content. All products clinkers behaved as fast setting, due to the early hydration of C4A3Ŝ, C4AF and CŜ. SBb, SBb_EAFS and SBb_R.M., with low C4A3Ŝ and high C4AF content, and in general, they exhibited low strength development. On the contrary, SBs_R.M. presented high early strength, due to the high content of C4A3Ŝ (~54% w.t.) and the results of the late strength were maintained at the levels of OPC 42.5N. In the case of SBs_R.M._DBW, the results showed that the addition of B2O3 had negative effect on the overall strength development of the cement. In order to evaluate the environmental behavior of SBb, SBb_EAFS and SBs_R.M. NEN 7345-tank leaching test, which refers to monolithic materials (“service life” scenario) was employed. The elution of heavy metals, Cr, Ni and V, which are contained in red mud and EAF slag, was tested. In the case of SBs_R.M. no Cr, Ni and V leaching was detected. In the case of SBb and SBb_EAFS however, quantities of Cr were detected at the eluate, which did not exceed the threshold of Existing (NEN7375) Monolithic Waste Acceptance Criteria_mg/m2 at 64 days (500 mg/m2). The SO2 sorption capacity from red mud was investigated next, aiming at its maximum valorization during the production of sulpho-belite cements. Aqueous suspensions (slurry) of 0%, 25% and 40% w.t. of red mud, were studied. The experiments were carried out in continuous flow stirred-tank reactor (CSTR). The results showed that the sorption capacity of was 23.2g SO2/kg slurry Ε.Ι. 25% w.t. and 49.3g SO2/kg slurry Ε.Ι. 40% w.t. The sorption of SO2 by the R.M. resulted in the formation of gypsum (CaSO4·2H2O) and pyrite (FeS2) and in an acid character of the initially basic slurry. It should be mentioned that the process did not lead to heavy metal (Cr, Ni and V) leaching from red mud. At the final part of the present work, a mathematical model was developed in order to estimate the energy demand and CO2 emission of different types of clinker. Mass and energy balances were used For the development of the model, in a system concerning the production of clinker. Three different clinker types were studied: alite clinker (OPC, Τfiring:1450°C and 1500°C), belite clinker with parallel valorization of EAF slag as raw material (BC, BC5 and BC10, Τfiring:1340°C, 1360°C and 1380°C) and sulpho-belite clinker with red mud and FGD gypsum valorization (SBS_R.M. για Τfiring:1320°C and 1330°C). The results showed that the production of belite and sulpho-belite type clinkers lead to the reduction of energy demand and to CO2 emissions compared to OPC. The minimum reduction of CO2 emission was 6.7% in the case of BC_1380°C and the maximum 38.6% for SBS_R.M._1320°C. The decrease of CO2 emission enhanced drastically the use of alternative raw materials, which are carbonate free (or low content). CO2 emissions are 897.18 kg/t, 839.90 kg/t, 804.67 kg/t, 771.79 kg/t and 558.34 kg/t (average values from the firing temperatures of each sample) for OPC, ΒC, BC5, BC10 and SBS_R.M. respectively. Overall, a reduction in the production costs of the clinker was estimated, rangin between 3.4-12.8 €/t clinker depending on the type of cement, the mineralogy and firing temperature of the clinker and the use of alternative raw materials.
Degree
thesis:*- Grantor dc:publisher
- University of Patras
- Year dc:date
- 2015
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Koumpouri, Dimitra
- Κουμπούρη, Δήμητρα
Subjects
dc:subject × 12Rights
dc:rights- Statement dc:rights
-
- BY_NC_SA
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/40786