Aristotle University Of Thessaloniki (AUTH)
Πειραματική και θεωρητική μελέτη μηχανικών ιδιοτήτων και φαινομένων μεγέθους σε νανοδομές και λεπτά υμένια
Abstract
dc:descriptionIn the context of this PhD thesis in the first part of the research, two thin film systems, each with a film thickness ranging from 100 to 500 nm, were manufactured using the Magnetron Reactive Sputtering method. The first system was Indium Tin Oxide (ITO) thin films on a silicon substrate (hard film on a softer substrate system), while the second thin films of Cu on a silicon substrate (a soft film on a harder substrate system).Subsequently, the samples were studied by nanoindentation experiments with a wide range of loads between 1 to 500mN in order to be able to calculate the nano-mechanical properties (elastic modulus and hardness) of the two different types of systems. The results for the two different types of films were recorded and compared with each other, leading to interesting observations.Imprints of nanoindentation experiments as well as their neighboring areas were investigated using optical microscopy, atomic force microscopy (AFM) and scanning electron microscopy (SEM) to study the deformation behavior and potential fracture patterns of the films for different impression loads.In the second part of the research an experimental study of monocrystalline silicon wafers was carried out using the nanoindentation method, which were also the substrates of the specimens, thin film-substrate systems of the first part of the research. The purpose of the research was to identify the factors influencing the occurrence of pop-in and pop-out effects during the nanoindentation process, while the magnitude of the pop-out phenomena that occurred during the experimental study was analyzed.In the last experimental part of the study, ITO / Si structures, that were prepared by the pyrolytic pulverization process, were investigated under cyclic nano-indentation, while they were leaking from DC current. The purpose of the research was twofold, firstly to examine the phenomenon of piezoresistive effect of structures based on indium tin oxide (ITO / X structures) and secondly to study changes in mechanical properties (elastic modulus, hardness of these structures during "cyclic" nanoindentation measurements while being leaked from DC current, concluding whether and to what extent it is feasible to use these structures in the construction of micro and nano-pressure sensors.Two new models were then developed, combining both Aifantis' Gradient Plasticity models with one and two characteristic lengths with the Korsunskys' composite hardness model to explain the nanoindentation size effect (ISE) in the complex thin film systems, for the right adaptation of the full range of hardness data of nano-indentation experiments, both in hard-films on a softer substrate and in soft films on a harder substrate.Finally, the gradient plasticity hardness models were used in experimental data of High Strength Steels HSS to see first if they work just as well for this type of materials, and second if they verify the full range of experimental data.This doctoral dissertation is divided into two main parts. The first part consists of 5 chapters, it concerns the theoretical approach of the present PhD and the theoretical background on which we relied to conduct the current research. The second consists of 6 chapters, which present and analyze the results of nanoindentation experiments and microscopic analysis, using optical microscopy, atomic force microscopy and scanning electron microscopy, as well as the development of composite gradient plasticity models were analyzed and their use in verifying experimental data of both thin films and bulk materials was investigated.More analytically in the first chapter is an extensive analysis of the two types of thin films used in this doctoral thesis. Transparent conductive ITO films and Copper thin films. There is an extensive reference to the specific properties they present as well as to their innumerable applications, giving an answer for the reason we chose them, while also making a historical review of the experimental work that preceded this dissertation in the ITO and Cu films.In the second chapter are presented the experimental techniques used for the construction and study of the thin films used in the dissertation, giving basic information on the methods of thin films development and especially sputtering deposition technique, the nanoindentation technique but also for microscopy methods were used, Atomic Force Microscopy (AFM) and Electronic Scanning Microscopy (SEM).The third chapter analyzes thoroughly the nanoindentation method used to determine the mechanical properties of our samples. Describe the basic principles of the method as well as the method of calculating the mechanical properties while loading and unloading curves were analyzed and the factors influencing the method are presented.Size phenomena, and in particular the indentation size effect (ISE), is described in the fourth chapter. Following is an extensive analysis of all models for the description of indentation size effect starting from the Aifantis gradient models and ending with the Nix-Gao model.The fifth chapter concerns the calculation of the real mechanical properties of thin films. This chapter gives a historical overview and partial analysis of the major models developed to calculate the real hardness and real elastic modulus in a complex thin film-substrate system.The sixth chapter contains the experimental study of the two thin film systems that were investigated, the ITO / Si and Cu / Si films. In this chapter the films were subjected to nanoindentation experiments on a wide range of loads. Their nano-mechanical properties (elastic modulus and hardness) were calculated and nanoindentation curves analyzed extensively. The results for the two different types of films were recorded and compared with each other. Subsequently, the imprints of nanoscale experiments as well as their neighboring areas were investigated using optical microscopy, atomic force microscopy (AFM) and scanning electron microscopy (SEM). The deformation behavior and possible fracture patterns of the films for different indentation loads were studied and a complete picture of the properties and differences between the two film systems and between the films with different thickness were recorded.The experimental study of monocrystalline silicon wafers is set forth in the seventh chapter. The aim was to study the occurrence of Pop-in and Pop-out phenomena by altering the parameters of nanoindentation experiments. The research was divided into two phases. In the first phase of the research, a statistical analysis of the presence of pop-in and pop-out phenomena was performed on monocrystalline Si wafer in relation to the maximum indentation load. In the second phase, experiments with very low loading / unloading rates were performed, while the maximum load was maintained the same as in the first phase. The results of the two phases were compared in order to arrive at conclusions regarding the dependence of pop-ins and pop-outs on the loading / unloading rate. Finally, the experimental data were statistically analyzed using a Tsallis q-distribution.The eighth chapter studies ITO / Si structures prepared by the pyrolytic pulverization method, under cyclic nano-indentation, while leaking with current. Two copper electrodes were placed in the samples, which were used to connect the samples to a Wheatstone bridge circuit. The voltage used came from a direct current source (DC). The samples were indented cyclic (5 cycles) while leaking with current of positive and then negative direction, depending on the polarity of the source. Changes in both the mechanical properties of the material and its resistance during nanoindentation measurements were observed for both polarities and were recorded.In the ninth chapter two new gradient plasticity models were proposed for the complicated thin film- substrate system to explain the hardness measurements of nano-indentation experiments of both hard-film on a softer substrate systems and of soft-film on a harder substrate systems .In the tenth chapter, the gradient plasticity models were used for experimental data from two different types of high strength (HSS) steel. In Quench and Partitioning Steels (QP) and in Transformation induced plasticity Steels (TRIP), in six different regions, three austenitic and three ferritic, to see if they work equally well for this type of materials while explaining the indentation size effect. Finally, in the Eleventh Chapter, an overview of the general conclusions and results concerning the doctoral dissertation was made.
Degree
thesis:*- Grantor dc:publisher
- Aristotle University Of Thessaloniki (AUTH)
- Year dc:date
- 2017
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Sidiropoulos, Alexandros
- Σιδηρόπουλος, Αλέξανδρος
Subjects
dc:subject × 14Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/43428