National Technical University of Athens (NTUA)
Generalized straight and curved beam theories with isogeometric analyis
Abstract
dc:descriptionThe present doctoral thesis is organized in seven chapters and two appendices. Each one of the chapters 2 to 6 consists of an introduction containing the necessary literature review of the corresponding problem, the statement of the problem, the numerical solution, a number of representative numerical examples and finally some concluding remarks. In the final chapter, the main conclusions drawn within the present doctoral thesis are summarized, while suggestions and goals for future research are proposed. In Chapter 2, the Analog Equation Method (AEM), a boundary element based method, is employed for the nonuniform torsional problem of bars of arbitrary constant cross section, considering a quadratic B-spline approximation for the fictitious loads of a substitute problem. In addition to this, refinement procedures have been employed in some of the numerical examples in order to investigate their efficiency in increasing accuracy. In Chapter 3, the AEM, a boundary element based method, is employed for the analysis of a homogenous beam element of arbitrary cross section (thin- or thick- walled) taking into account nonuniform warping and shear deformation effects (shear lag due to both flexure and torsion), considering B-splines for the approximation of the fictitious loads. The Isogeometric tools, either integrated in Finite Element Method (FEM) or AEM, are employed for the vibration analysis of this element, too. In Chapter 4, the static and dynamic generalized warping problem of horizontally curved beams of arbitrary cross section, loading and boundary conditions is presented. The proposed beam element possesses ten degrees of freedom (DOFs) per node in order to account for out-of-plane nonuniform warping due to both flexure and torsion (shear lag due to both flexure and torsion). In Chapter 5, the static and vibration analysis of straight or horizontally curved beams of arbitrary cross section, loading and boundary conditions including generalized cross sectional warping and distortional effects due to both flexure and torsion is presented. The aim of this Chapter is to propose a new formulation by enriching the beam’s kinematics both with out-of- and in-plane deformation modes and, thus, take into account both cross section’s warping and distortion in the final 1D analysis of curved members, towards developing GBT further for curved geometries while employing independent warping parameters, which are commonly used in Higher Order Beam Theories (HOBT). In Chapter 6, the beam formulations presented in Chapters 4 and 5 are employed together with design guidelines which specify the maximum spacing of intermediate diaphragms in order to prevent from excessive distortional effects in cross section’s plane. In Chapter 7, the main conclusions drawn in this doctoral thesis are summarized and the key features and novelties of the developed formulations are highlighted. Moreover, directions for further research are suggested.
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2017
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Tsiptsis, Ioannis
- Τσιπτσής, Ιωάννης
Subjects
dc:subject × 20- Ισογεωμετρική ανάλυση
- Καμπύλες δοκοί
- Γενικευμένη στρέβλωση
- Γενικευμένη διαστρέβλωση
- Λόγος poisson
- Μέθοδος πεπερασμένων στοιχείων
- Μέθοδος συνοριακών στοιχείων
- Διατάξεις τοποθέτησης ενδιάμεσων διαφραγμάτων
- Isogeometric analysis
- Curved beams
- Generalized warping
- Generalized distortion
- Poisson ratio
- Finite element method
- Boundary element method
- Diaphragms’ guidlines
- Επιστήμες Μηχανικού και Τεχνολογία
- Επιστήμη Πολιτικού Μηχανικού
- Engineering and Technology
- Civil Engineering
Rights
dc:rights- Statement dc:rights
-
- BY_NC_ND
- Language dc:language
- eng
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/44597