University of Patras
Σύνθεση, φυσικοχημικός και ηλεκτροχημικός χαρακτηρισμός ηλεκτροκαταλυτών για κυψελίδες καυσίμου υψηλής θερμοκρασίας PEM
Abstract
dc:descriptionAs the world's population and the energy demands of the modern digital era rise increasingly, conventional energy sources become more and more limited. The depletion of energy reserves drew attention to alternative, renewable energy sources that can satisfy the energy requirements in the world in an environmentally friendly and permanent way. Hydrogen (Η2) is the simplest and most abundant element in the universe and an ideal source of energy due to its high energy density. Also, its environmentally friendly electrochemical conversion in fuel cells is the main reason for the development of hydrogen fuel cells technologies. Among others, polymer electrolyte membrane fuel cells (PEMFCs) have been receiving increased attention due to their major advantages. PEMFCs are considered as the ideal clean energy power source for many applications (transportation, portable power generation, stationary applications) because of their high power density, high efficiency, constructive simplicity, quick start-up and zero emissions. The use of high temperature (HT) PEMFCs (160-200oC), provides several advantages comparing with the low temperature technology. These include simplifications of the fuel cell balance of plant, the generation of useful high-grade waste heat, flexibility to use not so pure Η2 or other fuels. The state-of-the-art Membrane Electrode Assembly (MEA) is based on phosphoric acid (H3PO4) imbibed polymer electrolytes and platinum on carbon (Pt/C) based electrodes. Very crucial issues concerning to the market penetration of fuel cells are their cost, reliability and long term stable operation. Pt supported on carbon electrocatalysts are the most efficient and stable materials for both the oxygen reduction reaction (ORR) at the cathode and the hydrogen oxidation reaction (HOR) at the anode of a PEMFC. Due to the high noble metal content (high cost) at the cathode (sluggish kinetics of the ORR), one of the most challenging areas towards the optimization of PEMFCs technology is the design and development of novel catalytic layers aiming at more active, uniform and stable electrochemical interfaces with minimal Pt loadings. In the first part of this thesis, synthesis and physicochemical characterization of Pt based electrocatalysts supported on covalently functionalized Multi Walled Carbon Nanotubes (f-MWCNTs) with low Pt loadings were carried out. These catalysts are intended for the cathode of HT-PEMFCs. In this respect, the wetting of the catalytic layer by a proton conductor (phosphoric acid, PA) is an important parameter for the formation of an active and extended electrochemical interface. Surface modification of oxidized MWCNTs (ox.MWCNTs) with polar pyridine moieties ((ox.MWCNTs)-Py), which interact with H3PO4 (proton conductor), can result in uniform distribution of the phosphoric acid throughout the catalytic layer, thus increasing the electrochemical interface and Pt utilization. Pyridine moieties improve the hydrophilic character of MWCNTs and provide anchoring sites, which enable interactions with Pt ions from Pt precursors, thus resulting in homogenous distribution of Pt nanoparticles (NPs) on the surface of the carbon support. The deposition of the metal was realized using the polyol synthetic procedure: reduction of metal precursor salt (H2PtCl6∙6H2O) in ethylene glycol (EG) solution. Reactions in different pH, time and temperature of reduction took place. Catalysts using different reaction conditions and different Pt loadings were synthesized. The introduction of pyridine groups on the sidewalls of the carbon support resulted in modification of the properties, not only in terms of quantitative deposition and dispersion, but also with respect to metal-support interactions, platinum crystal properties and/or oxidative state. In acidic reaction environment, in the case of samples based on ox.MWCNTs the formed Pt nanoparticles (NPs) have broad size distribution and medium dispersion. In the case of samples based on (ox.MWCNTs)-Py, synthesized in acidic pH, the formed Pt NPs were smaller, with narrow size distribution and uniform dispersion. Pyridine modified MWCNTs produced high- and atomic-dispersed catalysts for low Pt loadings (≤ 2 wt%) in the form of Pt2+-nitrogen-chloro complexes under acidic reaction environment. In the case of the Pt/(ox.MWCNTs)-Py catalysts increase in the loading led to increase in the percentage of the metallic Pt (Pt0) and formation of finely distributed Pt NPs, nevertheless always with a strong presence of the Pt2+ compared to corresponding samples without pyridines. Deposition of Pt NPs on f-MWCNTs in acidic reaction environment is faster than in basic. In basic environment the obtained particle size was smaller, but longer reaction time was needed for Pt deposition. At pH ≥ 11, the deposition was not quantitative despite the long reaction times. The nominal Pt loading could only be achieved when adjusting the pH of the solution to lower values (acidic) after the completion of the reaction in basic. In the case of Pt/(ox.MWCNT)-Py catalysts, prepared in basic reaction environment, even at low Pt loadings, metallic NPs were observed (no evidence of the aforementioned complexes formed in acidic reaction). The percentage of Pt2+ is higher compared to the corresponding Pt/ox.MWCNTs samples which synthesized in basic environment. Pt3Co/f-MWCNTs (atomic ration Pt/Co=3/1) catalysts using different reaction environment were also prepared using the polyol synthetic procedure and Co(NO3)2∙6H2O as the metal precursor salt. Deposition of any Co amount on f-MWCNTs did not occur in acidic reaction environment. Interestingly, in basic reaction (pH=11-12), although the nominal loading was not achieved and no alloying took place, Pt deposition was more efficient than the corresponding reaction in the absence of cobalt ions, denoting a differentiation in the deposition mechanism in the presence of cobalt. The nominal cobalt loading and the formation of the Pt3Co alloy were only achieved at extremely basic reaction conditions (pH=14). In the second part of the thesis, the electrochemical activity of the samples was studied towards ORR in 0.1 M HClO4 solution using the rotating disk electrode technique (RDE). Atomically dispersed catalysts on (ox.MWCNTs)-Py showed no activity towards oxygen reduction, denoting that the existing atomically dispersed Pt2+ was indeed completely inactive for the ORR. This revealed that the nanocrystals of Pt0 at higher Pt loadings were the active species towards ORR. The correlation between physicochemical or surface properties and the electrochemical performance showed that it is possible to alter the structural and electronic properties of Pt NPs and the interactions between metal and pyridine moieties on the carbon substrate in order to enhance its electrocatalytic activity. Even for low percentage Pt0 in the pyridine modified MWCNTs’ samples prepared under acidic conditions, the mass activity towards ORR, was significantly enhanced (~2 times) with respect to the non-modified samples or conventional carbon supports. Pt/(ox.MWCNTs)-Py catalysts prepared in basic reaction conditions showed comparable mass activity towards ORR with the corresponding catalysts prepared under acidic conditions. The electrochemical activity of Pt3Co/(ox.MWCNTs)-Py catalyst towards ORR showed that the formation of Pt3Co alloy did not further enhance the activity of Pt. In the third part of this thesis, the effect of Pt loading and proton conductor (H3PO4) amount in the formation of the electrochemical interface of an operating cathodic electrode in a HT-PEMFC was examined, using electrodes based on commercial 30 wt% Pt/C. The electrodes were tested towards ORR in a PEMFC at 180oC under different gas flows, using current-voltage diagrams. The study showed that the performance (especially under normal flows) was affected by the amount of H3PO4 and the dynamic response of the electrochemical interface with increased current and partial pressure of produced water. Based on the thickness of the catalytic layer, there is an optimal amount of acid that leads to uniform wetting of the catalyst and avoids decrease of the performance due to catalyst poisoning and/or mass transfer limitations. Also, the development of a reliable procedure for the quantitative in situ evaluation of the electrochemical active surface area (ECSA) in HT-PEMFCs, under the same conditions as those of the studied reactions, is described. The effect of constructive parameters (amount of H3PO4 and Pt loading at cathode) and performance’s parameters (steam partial pressure, operation temperature) in the formation of the electrochemical interface between TPS® polymer electrolyte membrane │Pt/C│gas was examined. The technique which used was oxidative stripping of adsorbed monolayer of CO (CO stripping). Εxperimental results provided valuable information on the extent and the stability of the Pt/C|H3PO4 electrochemical interface in the catalytic layer and how it was affected by high steam partial pressure (up to 30 kPa). Increase of the steam partial pressure progressively disrupted the electrochemical interface and decreased the ECSA. At low steam partial pressures, ECSA was similar for the different amounts of Η3PΟ4 tested. At steam partial pressures ≥20 kPa for a constant Pt loading, ECSA decreased in all cases, but more intensely for high amounts of Η3PΟ4. A deeper insight was gained by the combined analysis of the cyclic voltammetry (CV) experiments and the simultaneous CO2 formation by means of online mass spectrometry (MS). Interestingly, the current of the peak in the CV did not completely correspond to the CO electrooxidation reaction (therefore to the amount of produced CO2). The adsorption of OH- ions on empty Pt sites that occurred during electrooxidation of adsorbed CO, may resulted in the observed difference between the ECSA measured from the CV and the MS. Experiments in the absence of CO showed the occurrence of a side reaction, which did not correspond to CO2 (no CO2 was detected from the MS connected at the cathode outlet). The oxidation peak that appears in the CV from this side-reaction, increased with conditioning time and temperature, while decreased with steam partial pressure. This peak indicates either the presence of adsorbed reduced species, probably from H3PO4, which can block the Pt surface area during the CO adsorption, or the formation of Pt oxides. The difference in the ECSAs calculated from the CV and the MS (from the produced CO2) cannot be justified from this peak.
Degree
thesis:*- Grantor dc:publisher
- University of Patras
- Year dc:date
- 2019
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Zagoraiou, Eirini
- Ζαγοραίου, Ειρήνη
Subjects
dc:subject × 22- Κυψελίδες καυσίμου πολυμερικής μεμβράνης
- Αντίδραση αναγωγής οξυγόνου
- Τροποποιημένοι νανοσωλήνες άνθρακα
- Εναπόθεση λευκοχρύσου
- Υψηλή/ατομική διασπορά
- Ηελκτρόδιο περιστρεφόμενου δίσκου
- Ηλεκτροκαταλυτική ενεργότητα
- Πείραμα ηλεκτροχημικής οξείδωσης CO
- Ηελκτροχημικά ενεργός επιφάνεια
- Polymer electrolyte membrane fuel cells (PEMFCs)
- Oxygen reduction reaction (ORR)
- Functionalized carbon nanotubes
- Platinum deposition
- High/atomic dispersion
- Rotating disk electrode (RDE)
- Electrocatalytic activity
- CO stripping experiment
- Electrochemical active surface area
- Φυσικές Επιστήμες
- Χημεία
- Natural Sciences
- Chemical Sciences
Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/45838