University of Patras
Ανάπτυξη ανοδικών και καθοδικών νανοδομημένων υλικών για εφαρμογή σε μπαταρίες λιθίου
Abstract
dc:descriptionDue to the dependence of modern economies on a reliable and affordable electricity supply and the need to address climate change arising from the rapid depletion of fossil fuels, the evolution of energy systems is a major subject of the worldwide research. Lithium-ion batteries are of great technological interest for use as energy storage devices, since they offer higher specific energy comparing to other conventional rechargeable battery systems. The research focuses on finding innovative cathode and anode electrodes based on various nanostructures, which can deliver high capacity, have easy manufacturing and low economic and environmental impact, for the development of advanced batteries with high specific energy and power values. In the present doctoral thesis, LiAl0.1Mn1.9O4 spinel nanostructure was prepared via the combustion synthesis, was extensively studied and used as cathode electrode. The research focused on two main lines: (a) coating of electrode surface with a protective dense or porous titanium nitride film using magnetron sputtering process and (b) influence of various parameters on electrode fabrication, such as the substrate-current collector used, the active material loading and the role of binder in active mass. Αdditionally, graphene aerogels were prepared using hydrothermal process followed by freeze-drying, were studied and used as anode electrodes. The research focused on the ability of chemical bonding between the aerogel and substrate by using the aliphatic diamine TETA or the aromatic diamine OPD. The techniques used for the investigation of physicochemical characteristics are: X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy and Raman spectroscopy. The electrochemical properties of the samples were examined using galvanostatic charges/discharges, electrochemical impedance spectroscopy and cyclic voltammetry. The electrochemical measurements were performed using two-electrode electrochemical cell. Titanium nitride-modified electrodes (having a thickness of 50 nm), exhibited enhanced electrochemical performance as compared to the unmodified sample, while the use of dense coating layer proved to be the most effective approach of active material protection, delivering a significant capacity retention in stability test of 400 cycles. The unmodified LiAl0.1Mn1.9O4 electrode suffered from rapid capacity fading, as a result of faster degradation of spinel active material. The above results are in good agreement with XPS analysis after the stability test, where the TiN dense film remained on coated electrode. CV measurements confirmed the improved reversibility for modified electrodes, while EIS data accompanied with the calculated Li+ coefficient values revealed the enhanced Li+ transport promoted by the protective conductive layer. The evaluation of various parameters regarding the LiAl0.1Mn1.9O4 electrode fabrication revealed the following: (a) although electrodes with higher loading start with lower capacities, they show better capacity retention in different charge/discharge rates, (b) the role of binder proved to be important by holding the electrode particles together and (c) carbon paper enhanced the performance especially in higher charge/discharge rates, since it acts as extension of electrode conductive network. From a practical point of view, the electrode with 4 mg cm-2 loading, use of binder and carbon paper substrate, presented the most attractive electrochemical properties, combining high discharge capacity and retention under different charge/discharge current densities. Comparison of TETA and OPD diamine regarding their contribution to the chemical bonding of graphene aerogel on carbon paper substrate led to the conclusion that the former from the category of aliphatic diamines provides stronger connected pathways for Li+ transfer, during the charge/discharge process. SEM images confirmed the formation of 3D porous structure of aerogel on the treated surface of carbon paper. Subsequently, CV and cycling measurements with different charge/discharge rates, revealed more stable electrochemical surface area and capacity, respectively, for the TETA-containing electrode.
Degree
thesis:*- Grantor dc:publisher
- University of Patras
- Year dc:date
- 2020
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Angelopoulou, Pinelopi
- Αγγελοπούλου, Πηνελόπη
Subjects
dc:subject × 22- Μπαταρίες ιόντων λιθίου
- Αποθήκευση της ενέργειας
- Ανοδικό ηλεκτρόδιο
- Καθοδικό ηλεκτρόδιο
- Νανοδομημένα υλικά
- Σπινελική δομή
- Οξείδια λιθίου μαγγανίου
- Αεροπηκτώματα γραφενίου
- Lithium-ion batteries
- Energy storage
- Anode electrode
- Cathode electrode
- Nanostructured materials
- Spinel structure
- Lithium manganese oxides
- Graphene aerogels
- Επιστήμες Μηχανικού και Τεχνολογία
- Νανοτεχνολογία
- Άλλες Επιστήμες Μηχανικού και Τεχνολογίες
- Engineering and Technology
- Nano-Technology
- Other Engineering and Technologies
Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/47403