National Technical University of Athens (NTUA)
Μελέτη επίδρασης του υδρογόνου στη μηχανική συμπεριφορά μεταλλικών σωληνώσεων μεταφοράς πετρελαιοειδών και υδρογονανθράκων
Abstract
dc:descriptionThe main target of this doctoral dissertation is the study of the effect of atomic hydrogen electrodiffusion phenomenon on the mechanical behavior of metallic pipelines, which are used intransportation of petroleum products and hydrocarbon gases. In the first chapter, the hydrogen embrittlement phenomenon due to the electro - migration effect of atomic hydrogen in the crystalline structure of welded aluminum alloys, that are applied to gas transmission lines and oil extraction platforms, was studied. The studied Friction Stir Welded specimens were extracted from pipes with 3 mm wall thickness and an external diameter of 16 in. During the experimental implementation of this research project in the first stage, the cathodic polarization process of welded specimens took place within an electrodynamically and electrokinetically controlled hydrogendiffusion field and then the pre - charged specimens were subjected to slow strain rate tensile test at air ambient (according to ISO 3183, ASTM G148 - 97, ASTM E 8M - 04 standards and the research activity to meet the technological requirements as indicated by the Europipe organization in Germany in collaboration with American Petroleum Institute). The present study focused on the evaluation of the Hydrogen Embrittlement susceptibility of dissimilar friction stir welds of AA5083-H111 and AA6082-T6 aluminum alloys. The main embrittlement mechanisms were studied for applied cathodic polarization current densities of 20, 50 and 80 mA/cm2 and duration of cathodic charging process for 2 and 4h. The slow strain rate tensile tests were performed with a grab removal speed of 0.01 mm/min in order to favor hydrogen diffusivity and hydrogen trapping effect (in deep and irreversible traps), according to the ASTM E 8M – 04 standard. With the increment of applied current density from 20 to 80 mA/cm2 a severe reduction of ductility and a lower decrease of yield stress and ultimate tensile strength were observed. The fractured surfaces were characterized by increased volume fraction of embrittling features such as river patterns, quasicleavage facets and teardrop ridges. For the most extreme cathodic polarization conditions (80 mA/cm2, 4h) the fracture was realized into the fine - grained microstructure of stir zone. Furthermore, by stereoscopic analysis, scanning electron microscopy, X-ray diffractometry and EBSD analytical technique an increased volume fraction of hydride and blister formation was determined, which was related to the restriction of the atomic hydrogen electrodiffusion field in high angle grain boundaries with elevated misorientation angle distribution factor and in semi – coherent or non – coherent interphases between solidification phases, intermetallic precipitates and matrix material. Additionally, it was detected the evolution of stepwise microcracking phenomenon, with preferential points for crack initiation the interfaces between hydrides, embrittling phases with stoichiometrical ratio Al3Mg2 and aluminum substitutional solid solution. In the second chapter, the embrittlement effect due to the electrodiffusion of atomic hydrogen into the crystalline structure of welded pipeline steels transporting petroleum products and hydrocarbon gases in cases of underground installation was investigated. During the experimental implementation of this thematic object, in the first stage, the cathodic polarization procedure took place within an electrochemical stimulated field enriched with hydrogen cations. In the second stage the mechanical testing was carried out through the Crack Tip Opening Displacement technique (Ex – situ hydrogen cathodic charging and CTOD testing). This research work focused on the investigation of the correlation between hydrogen cathodic charging conditions and toughness properties of SAWL welded X65 pipeline steels. The studied steel specimens were extracted from pipes with 19 mm wall thickness and an external diameter of 29 in, without been subjected previously to operational conditions. The experimental technique which was applied to determine the characteristic parameters associated with toughness drop (KQ, J, CTODel, CTODpl) was the CTOD testing after hydrogen cathodic charging process according to BS7448 and ISO12135 standards, with a piston displacement speed of 0.95 mm/min. The hydrogen cathodic polarization process was carried out in a vertical electrolytic cell with applied current densities of 10, 20, 30 mA/cm2 and hydrogen cathodic charging duration 48 h. Through this study, interesting results were provided concerning the diffusion depth, the diffusion coefficient and the desorption time of atomic hydrogen, the surficial density, the morphology and nucleation sites of blisters, the initiation points and the propagation mode of stepwise microcracking as far as toughness properties and fractographic analysis. The maximum diffusion depth value and the highest diffusion coefficient is assigned for each current density field in the region of heat affected zone and the minimum in the area of fusion zone. Finally, the fusion zone is considered to be more prone to the occurrence of embrittlement phenomena compared to base metal. The rate of toughness parameters drop was detected to be higher for current densitiesbetween 0 – 10 mA/cm2 and 20 – 30 mA/cm2, where the non - faradaic cathodic polarization fieldpromotes the electrochemical reduction of hydrogen cations to atomic hydrogen between metal andelectrolyte interface. In the third chapter, the embrittlement effect due to the electrodiffusion phenomenon and electro-migration effect of atomic hydrogen in X52, X65 and X70 pipeline steels, which are used for the transportation of petroleum products and hydrocarbon gases in cases of underwater installation, was studied. For the experimental implementation of this project, the development of an aggressive electrostimulated field for the creation of electrodynamically and electrokinetically assisted diffusion fronts of hydrogen cations and the cathodic polarization of specimens took place simultaneously with their mechanical testing through the CTOD technique, in a horizontal type electrolytic cell according to ISO 3183 and ASTM G148 – 97 standards (In – situ hydrogen cathodic charging and CTOD testing). More precisely, the present research domain focused on the investigation of in – situ hydrogen charging effect during Crack Tip Opening Displacement testing (CTOD) on the fracture toughness properties of X52, X65 and X70 pipeline steels. The studied steel specimens were extracted from pipes with 11 mm wall thickness and external diameter 26 in. The fracture toughness parameters were determined after imposing the fatigue pre-cracked specimens on air, on a specific electrolytic cell under a slow strain rate bending loading (with a piston displacement speed of 0.01 mm/min according to BS7448 and ISO12135standards), for applied current densities of 10 or 20 mA/cm2 and hydrogen cathodic charging duration 26 h. In sequence, the characteristic parameters related to fracture toughness (such as J, KQ, CTODel, CTODpl) were calculated by the aid of the Force – Crack Mouth Open Displacement curves and the relevant analytical equations. According to the obtained experimental results, by increasing the applied current density field during in – situ hydrogen cathodic polarization process the fracture toughness parameters were decreasing continuously. Through this study, interesting results were provided concerning the hydrogen induced toughness decrease, the micro-mechanisms which contribute to failure, the morphology and surficial density of blisters and microcracks, the microhardness increment at pipeline steel surfaces, as far the diffusion depth and the diffusion coefficient of atomic hydrogen into the structure correlated to the applied current density during the in - situ hydrogen cathodic charging process. The novelty of this research work is attributed to the use of an environmental friendly electrolyte consisted of 30 g/L NaCl and 3 g/L NH4SCN (which satisfies green chemistry’s requirements) for elevated values of the applied current density field (10 and 20 mA/cm2 ) during the in – situ hydrogen cathodic charging process and slow strain rate bending. The applied current densities exceeded the above of other researchers, which haven’ tbeen higher than 10 mA/cm2 . Also, with the use of the given electrochemical environment, the study of the development of electro-kinetically assisted pulsed atomic hydrogen diffusion fronts in the micrographic texture of the specimens without the unwanted contribution of corrosion phenomena (localized anodic polarization effect) which disorient the main conclusions about the type of micromechanisms that contribute to the manifestation of hydrogen embrittlement phenomenon was achieved. Moreover, these experiments took place in order to investigate the existence or not of a thermodynamic or electrokinetic - electrodynamic potential threshold which leads to the hydrogen absorbed diminishing effect independently of the increment of the applied current density. In total through the ensemble of the obtained results the novelty of the present dissertation is mainly based on the correlation of both thermodynamic quantities (penetration depth and diffusion coefficient of atomic hydrogen, surface coverage density of blisters and microcracks) as well as kinematic magnitudes (required atomic hydrogen desorption time and time threshold for stabilizing the cathodic overvoltage potential of the electrolytic system) with the degradation of the main mechanical properties, as they arise either from static or semi-static mechanical testing in ferrous and non-ferrous alloy systems, which find application in subsoil and submarine fuel transport facilities (either gas or liquid phase). Finally, there is no published work in the international research community that refers to embrittling micro-mechanisms due to hydrogen electro – diffusion phenomenon, either in homogeneous or inhomogeneous welded aluminum alloys through the FSW technique, which are used in high voltage insulated natural gas pipelines and on oil extraction platforms (platforms in offshore sectors mainly for assembling). The above treaty, however, has been an urgent technological necessity for the last five years to be solved, by both Europipe and the American Petroleum Institute, as a result of which the first research part of the present doctoral dissertation is substantiated.
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2020
Author and committee
dc:creator, dc:contributor.*- Author dc:creator
-
- Κυριακοπούλου, Έλενα-Αλεξία
Subjects
dc:subject × 9Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/48254