University of Patras
Σύνθεση και πειραματικός χαρακτηρισμός κόλλας βιολογικής βάσης για δομικές εφαρμογές: ενίσχυση της κόλλας με νανοσωλήνες άνθρακα
Abstract
dc:descriptionThe increasing use of epoxy adhesives in construction and cosmetic applications in different industries combined with the new restrictions on the use of mineral resources and the produced environmental footprint and the need for increased recyclability has caused great interest in the last decade for the development and production of bio-based epoxy adhesives. The relative progress that has been made is small. Two of the main issues to be solved of biological base adhesives are the low mechanical properties in relation to conventional structural adhesives and their sensitivity to environmental aging. At this stage, applications of biologically based adhesives and resins are limited to cosmetic constructions bearing low or zero loads. In the present PhD thesis, a new bio-based adhesive, which is intended for structural and decorative applications, was developed and characterized experimentally. The adhesive is based on the ingredients of epichlorohydrin and cardanol. Epichlorohydrin is of plant origin and is produced from glycerin, while cardanol is produced from anacardic acid, which is found in the oil of the cashew nut. The steps of the work include the stoichiometric ratio of mixing the components, the laboratory synthesis of the adhesive, the construction of adhesive samples and the adhesive joints. Optimization was applied for each individual process. In particular, parametric studies were performed on the effect of stoichiometric ratio on the viscosity and mechanical properties of the adhesive and the curing temperature on the mechanical properties of the adhesive. The degassing process was optimized in terms of adhesive quality. Different surface treatments were applied to the surfaces of the aluminum and composite specimens to improve the adhesion of the adhesive to the surfaces, while the surface chemical treatment was optimized for the aluminum surface. Finally, different methods and parameters were applied for the dispersion of carbon nanotubes in the adhesive given the difficulty of homogenizing the material due to the high viscosity of the adhesive. For the experimental characterization of the adhesive material, tensile, fracture toughness and dynamic mechanical analysis tests were performed on bulk adhesive specimens as well as tensile tests on single-lap shear joints of aluminum (2024-T3) and composite adherends. The adhesive material was tested for the presence of pores using a high-resolution microscope. Two different surface treatments (grinding and chemical treatment) were applied to the aluminum adherends, while one (grinding) to the composite adherends. In order to study the effect of environmental aging on the mechanical behavior of the new adhesive, bulk adhesive specimens and joints were subjected to accelerated hydrothermal aging (70οC/85%RH) until saturation. Also, in order to examine the possibility of enhancing its mechanical properties, the adhesive was reinforced with carbon nanotubes in three different contents: 0.5%, 1.0% and 2.0% by weight. The morphology of the reinforced adhesive was investigated by scanning electron microscopy tests and an attempt was made to link these results with the results of the mechanical tests. For the aged adhesive specimens and adhesive joints and the reinforced adhesive specimens and the reinforced adhesive joints, all the aforementioned mechanical tests and dynamic mechanical analysis tests were repeated. The experimental results showed that the bio-based adhesive has a Young’s modulus of 1.85 GPa, a tensile strength of 60.6 MPa, a stress intensity factor of 1.53 MPa‧√m and a glass transition temperature of 65.1°C. Microscopy examinations showed no pores in the adhesive material. The shear strength of the adhesive for aluminum bonding is 6.35 MPa for the grinding surface treatment and 13.64 MPa for the chemical surface treatment, which demonstrates the importance of the surface treatment in the adhesive joints. The shear strength of the adhesive for composite bonding is 22.27 MPa. The application of hydrothermal aging caused a decrease in the Young’s modulus, tensile strength stress intensity factor and glass transition temperature of the adhesive by 12.97%, 34.98%, 3.2% and 13.8%, respectively. These results show that the adhesive is quite prone to environmental aging. In contrast, the application of hydrothermal aging caused a small increase in the shear strength of the adhesive for both the aluminum and composite joints. The reinforcement of the adhesive with carbon nanotubes led to an increase in the Young’s modulus, the stress intensity factor and the glass transition temperature of the adhesive and to a decrease in the tensile strength. Both the increase and the decrease of the properties are increasing with the increase of the reinforcement content. The maximum increase in the Young’s modulus is 6.4%, in the stress intensity factor is 7.2% and in the glass transition temperature is 5.6%, while the maximum decrease in tensile strength is 20.6%. These conflicting results are due to the presence of carbon nanotube agglomerates in the adhesive which, as shown in the scanning electron microscopy images, had an increasing population and size with increasing the carbon nanotube content. In addition, the addition of carbon nanotubes led to a very large increase in the shear strength of the adhesive in the aluminum joints (the maximum increase is 57% for the 2wt%) and a significant increase in the shear strength of the adhesive in the composite joints (10.4% for the content of 2wt%). From the evaluation of the experimental results, the following can be concluded: • For almost all experimental series, the standard deviation of the measurements is very small, which is indicative of the repeatability of the processes of the adhesive synthesis, the specimen fabrication and the mechanical testing processes. • In all tests of adhesive joints, a cohesive failure was observed, which is indicative of the manufacturing quality and the high strength of adhesive joints. • The average values of all adhesive properties (bulk and joint) are in their majority above the average of the properties of commercial structural adhesives. In parallel with the experimental process, a life cycle and cost analyses of the bio-based adhesive were performed. Specifically, an environmental impact study of the production of the adhesive was carried out based on the ISO 14040 standard and six potential indicators were calculated: the potential for depletion of abiotic resources, the potential for acidification, the potential for freshwater eutrophication, the potential for ozone depletion, ozone, and the potential for global warming. The input data for the analyses were obtained from the literature and from the manufacturers of the adhesive components. A common commercial epoxy resin was used as a reference material. The comparison of potential values showed that the new bio-based adhesive has much less environmental impact than the commercial resin and a much lower production cost. On the contrary, the reinforcement of the adhesive with carbon nanotubes leads to a higher global warming potential than the epoxy adhesive and to a higher production cost. In conclusion, in the present PhD thesis, a new bio-based adhesive was developed and characterized experimentally. In addition, the effect of environmental aging on the mechanical properties of the adhesive and the possibility of enhancing its mechanical properties by adding carbon nanotubes were examined. The results show that the new adhesive due to its high mechanical properties, low environmental footprint and low production cost shows good prospects for future use in cosmetic and some structural applications
Degree
thesis:*- Grantor dc:publisher
- University of Patras
- Year dc:date
- 2021
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Tzatzadakis, Vasileios
- Τζατζαδάκης, Βασίλειος
Subjects
dc:subject × 8Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/49528