University of Patras
Ανάφλεξη, καύση και πυρόλυση σύνθετων αεροναυπηγικών υλικών και εξάπλωση φλόγας σε περίκλειστους χώρους
Abstract
dc:descriptionThe current thesis is focused on the investigation of fire behavior of aeronautical composite materials and flame spread in inaccessible areas of the aircraft. Research in this direction was deemed necessary as the increased use of composite materials in modern aircrafts, which under combustion and pyrolysis processes emit heat and toxic gases, poses the risk of significantly increasing the fire load, and consequently fire hazard, especially in a confined space such as the aircraft interior. Despite extensive research on the mechanical properties of composite materials, research on certain aeronautical materials such as sandwich composites in relation to their fire performance is very limited. Large or intermediate tests used by the US Federal Aviation Administration (FAA) and the European Aviation Safety Agency (EASA) for the certification of aviation materials are particularly costly and time consuming. Therefore, in recent years significant efforts have been made to establish simpler, performance-based Standards by using Small-Scale tests. However, their research includes tests that have a pass fail character and focus on the quantitative assessment of fire behavior of materials. It is apparent that employing small-scale devices and developing the appropriate analytical methods might provide a set of tools for evaluating fire behavior of materials from their design phase. This will ensure the development of new products in relation to their fire performance, as equipment and time requirements are significantly reduced since fewer experimental tests are required.First, the theoretical background relative to the current research is presented. In particular, the main processes and kinetics of the thermal decomposition of composite polymeric materials are described. The mechanisms of pyrolysis of a solid fuel under the influence of external heating are extensively analyzed, from the thermal decomposition stage, to the production of gaseous fuels that mix and lead to ignition, by describing the processes involved in both the solid and gaseous phases. Piloted ignition is thoroughly presented as all standard tests, such as the Cone Calorimeter, attempt to describe the ignition of solid fuels with the assistance of a source of pilot. The significant simplifications and hypotheses for the analytical solution of the surface temperature that lead to simple expressions of the external heat flux with the ignition time which essentially separate materials into thermally thick (having an internal thermal gradient) and thermally thin (uniform temperature distribution) are also presented. The ignition criteria are then given with special emphasis on the critical surface temperature criterion employed in the present work. Then the mechanisms of flame spread over solid fuels are analyzed and the experimental approaches and models adopted based on the literature review are also described. The problem of flame spread is approached depending on the air flow direction, as opposite and concurrent spread, over thermally thin or thick materials. The factors that affect the spread of the flame are also described along with the relative research conducted in this area. In order to study the thermal degradation process of the materials under investigation, tests performed in a Thermogravimetric Analyzer (TGA), at different heating rates, under inert atmosphere, are initially presented. The experimental results of the thermal degradation process including mass loss and its temperature derivative are first described and analyzed. The results were quite encouraging as they showed that the aeronautical materials tested in the current work had satisfactory thermal stability. Different analytical techniques were used and evaluated in order to calculate the kinetic parameters such as activation energy and pre exponential factor and to determine the reaction function of the decomposition process. Given that the main thermal decomposition stage of the composites consists of overlapping processes, one-step reaction was considered for the analysis, which is the simplest approach, especially for large-scale simulations, unlike for the thermoplastic cable where both single and multiple stage reactions were adopted. The analysis showed a satisfactory convergence of the measured variables that were then used for the reconstruction of the TGA curves which appeared to capture quite reliably the main phase of the decomposition process, proving that the adopted method has satisfactory predictive capability.The identification of thermal degradation processes and the calculation of the kinetic parameters are followed by the investigation of ignition and combustion mechanisms in the Cone Calorimeter apparatus at different levels of the intensity of the incident radiation. The construction of a customized sample holder for the specimens limiting to one-dimensional heat transfer along with the ability to measure the temperature on the exposed surface and on the back of the samples was used to calculate the ignition temperature and study the thermal degradation processes and heat transfer through the tested materials. The above measurements were assisted by the use of an infrared camera. Fire reaction properties were also measured including ignition time, heat release rate, smoke production, carbon dioxide, and carbon monoxide yield along with a set of parameters such as mass loss, effective heat of combustion, and total heat release. The excellent fire reaction properties such as the low amounts of heat release and the long ignition times showed that these materials are fire retardant. The formation of a char residue layer on the surface during their thermal decomposition also contributed to this behavior, affecting the heat transfer mechanisms to and from the combustion zone. The thermal properties were then calculated based on a modified analytical method and the results obtained were evaluated in comparison with the corresponding experimental values. The results of the method, which has been applied exclusively to common materials such as wood, showed satisfactory convergence, proving that this method can be used in a new expanded range of aeronautical materials.Finally, a novel experimental apparatus, the Confined Fire Apparatus (CFA), which was designed and constructed in order to measure flame spread parameters such as flame spread rate, critical heat flux for flame spread and ignition, and flame spread temperature in confined spaces such as the inaccessible areas of the aircraft is presented. The theoretical model developed to describe the problem based on the selected fire scenario and the experimental results performed in horizontal direction under free flow natural conditions, different imposed irradiant heat fluxes and preheating times are thoroughly analyzed. Flame spread rate was calculated either visually by analyzing the snapshots of the flame front in time or by the second time derivative of temperature by employing an array of thermocouples at a constant distance. The experimental results showed that the thermal flame spread model developed to describe the heat transfer mechanisms and the corresponding equations used had good predictive capability. In addition, fire reaction properties were measured via a tube connecting the CFA device to the Cone Calorimeter and correlation functions were developed between flame front displacement and heat release rate.
Degree
thesis:*- Grantor dc:publisher
- University of Patras
- Year dc:date
- 2021
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Papadogianni, Vasiliki
- Παπαδόγιαννη, Βασιλική
Subjects
dc:subject × 16Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/50067