Back to search

University of Ioannina

Development and characterisation of new high entropy alloy systems of dual and/or multiple phases

Abstract

dc:description

This doctoral thesis focuses on the gradual design of new low- to high-entropy alloys based on the NiAl-Cr elemental core and the evaluation of their mechanical properties and surface degradation response. In particular, two main alloy categories of non-equimolar compositions were produced using the vacuum arc melting technique and developed as follows: (a) the refractory high-entropy alloys including the Ni-Al-Cr-Mo-W and the Ni-Al-Cr-Mo-V systems and (b) the 3d transition element containing alloys, including the Ni-Al-Cr-Fe-Mn and the Ni-Al-Ti-Fe-Mn systems. For all the respective alloys of each individual system, various theoretical phase formation models were evaluated as an initial stage of final phase prediction, while the actual microstructural features were extensively studied using widely used experimental techniques. Additionally, the corresponding solidification mechanisms were also proposed, as well as some interesting and unique morphological characteristics identified in each case, were further analyzed.As far as the mechanical properties are concerned, micro-hardness measurements were carried out for all the produced structures and the results were evaluated in conjunction with the wear data provided after testing against a ball-on disc dry-sliding wear configuration. These surface degradation tests were conducted under specific experimental conditions (two different loads, 1000 m sliding distance and a metallic ball as a counter body material). In each case, the wear data (e.g. mass loss and wear rate) were recorded, while the wear surfaces and debris were studied in order to formulate the corresponding degradation mechanisms.Finally, the characterization of the produced alloys was completed by the examination of the creep behaviour of some selected structures. The basic creep parameters as well as the respective creep displacement- holding time curves were calculated and evaluated on both the primary and eutectic phases under specific experimental conditions (using a Berkovich indenter, 10 s as holding time and two different penetration depths of 500 nm and 1000 nm) providing additional information concerning the alloys’ response.More specifically, with respect to the NiAl-Cr low-entropy alloy system, the predictions of the NiAl-Cr pseudo-binary phase diagram, concerning the final microstructures, were verified for the investigated NiAl-25Cr, -33Cr, -40Cr, -45Cr, -60Cr and -80Cr alloy compositions. Additionally, the phase selection theoretical models indicated phase segregation. In fact, the evaluation of the actual crystal structures and microstructures of the alloys revealed the presence of an ordered (B2) and a disordered BCC phase, with NiAl and Cr being the main primary phases for the hypo-eutectic (NiAl-25Cr and NiAl-33Cr alloys) and the hyper-eutectic (NiAl-40Cr, -45Cr, -60Cr and -80Cr alloys) alloys, respectively. Additionally, eutectic micro-constituent was also present in the cases of the NiAl-25Cr, -33Cr, -40Cr and -45Cr as expected, while in the case of the alloys with the highest Cr-content (NiAl-60Cr and -80Cr) limited to zero eutectic phase was observed. It was found that the T0 temperatures, along with undercooling and recalescence phenomena were responsible for the microstructural outcome. Furthermore, the low-entropy alloys exhibited high micro-hardness values, which were increased with increasing Cr content. In terms of their wear response, the alloys’ wear rates seemed to follow the classic law by Archard, according to which the lower the micro-hardness, the higher the wear rate. The main wear mechanisms was a combination of both the detachment-delamination and abrasive wear mode. Finally, the nano-indentation tests performed in each case revealed interesting results concerning the basic parameters of both the primary and the eutectic phases, while the loading and the creep displacement curves seemed to follow the power law with some individual cases showing the typical “sudden bursts”.The actual microstructural characteristics of the Ni-Al-Cr-Mo medium-entropy alloys with both low and high Mo concentrations were very interesting. In the case of low Mo additions, the alloys exhibited simple microstructures of primary and/or eutectic phases. On the contrary, the gradual introduction of high Mo content by the subsequent substitution of Cr, led to unique features such as, halo-like areas as peritectic reaction products in which two different intermetallic phases, namely MoNi and AlMo3, coexisted. In addition, it was evident that Mo compositions greater than 20 at.%, led to the progressive elimination of the eutectic micro-constituent. Finally, when the alloys’ wear behaviour is concerned, no trend could be suggested, mainly due to the different oxide phases and the intermetallic peritectic halos present in each case. The wear mechanism, however, was found to be the delamination-detachment mode for all cases.As far as the three high-entropy alloys of the Ni-Al-Cr-Mo-W systems are concerned, Tungsten, with the highest melting point, seemed to govern the solidification initiation. As such, the observed microstructures consist of primary W(Mo) phases, with a grey phase being formed in the periphery of the primary core in each alloy case. The main core of this grey phase was identified as a Cr-Mo-rich solid solution, while some Al-Cr-based (in all three cases) and the MoNi (is the case of the alloy with the highest W content) intermetallic compounds were also formed. Adiabatic conditions were further established in the remaining liquid, leading to the formation of secondary primary NiAl and eutectic micro-constituent at the final stages of solidification, while a Cr-rich phase precipitated into the NiAl phase due to reduced solubility upon cooling. According to the micro-hardness measurements, the investigated compositions seemed to have no significant alterations, however, the addition of W into the quaternary Al-Ni-Cr-Mo system significantly reduced the alloys’ hardness. Finally, the sliding wear response of the produced alloys seemed to follow the classic law proposed by Archard, following a trend that was further supported by various factors like, the nature of the oxides and the integrity of the interface between the primary and the grey phases. The delamination-detachment was found to be the main wear mechanism for all cases, while an abrasive mode was also evident in the case with the highest W content.In the case of the Ni-Al-Cr-Mo-V alloy system, the alloy with the lowest Mo-V concentration exhibit a eutectic micro-constituent of typical lamellar configuration (Ni,Al-rich dark areas and Cr-rich light areas) covering the whole microstructure, while its morphology seems to alter from the central areas (fine eutectic) to the outer region of the eutectic cell (coarse eutectic). On the contrary, the NiAl-20Cr-10Mo-10V and NiAl-15Cr-12.5Mo-12.5V alloys exhibit similar microstructures showing the characteristic dendritic configuration (Mo(V,Cr)-rich primary core) along with other significant features like, a grey phase (Cr-rich) around the primary dendrites, a dark phase (Ni, Al-rich) in the inter-dendritic area and eutectic micro-constituent which is significantly decreased as the Mo-V concentration increases. At the last stages of solidification, the precipitation of Cr within the supersaturated Ni-, Al-rich phase occurs, due to its reduced solubility upon cooling. According to the micro-hardness measurements, the investigated compositions seemed to have no significant alterations, however, the substitution of W with V, has a great effect on the alloys’ strengthening behaviour. Finally, the sliding wear response do not follow the classic law proposed by Archard, while other factors like the nature of the oxides and the integrity of the interface between the primary and the eutectic phases were used to support the alloys’ behaviour. The delamination-detachment mode seems to be the main wear mechanism for all cases.Moving on to the second category of the 3d transition element containing alloys and the case of the Ni-Al-Cr-Fe-Mn alloys in particular, two sub-categories were developed: The NiAl-containing alloys and the Ni3Al-containg alloys. In both cases, two distinct phases, namely a Ni-Al-rich B2 phase and a Fe-Cr-rich A2 phase, were identified, while Mn was uniformly distributed within both phases. In addition, the solidification sequence was totally explained through the NiAl-Cr pseudo-binary phase diagram. When the NiAl-containing alloys are concerned, a eutectic microstructure was observed, while the alloys’ high hardness was attributed to the presence of the intrinsically hard NiAl intermetallic compound. On the contrary, in the Ni3Al-containing alloys, the microstructure exhibited a characteristic dendritic configuration, while their hardness values were significantly low, mainly due to the presence of the intrinsically ductile Ni3Al intermetallic compound. Nonetheless, in both alloy categories, the sliding wear response was characterized by a surface oxidation and delamination material removal mode.Finally, the development of the Ni-Al-Ti-Fe-Mn alloy was achieved. The (FeMnNi)84(AlTi)16 high-entropy superalloy was investigated in its as-cast and solution treated conditions, while heat treatments at several different times were also conducted. Concerning its microstructure, a double FCC matrix was identified for the as-cast, solution treated and 160 h aged alloys. In fact, the existence of Fe-rich and Ni-rich areas was correlated to the presence of a solidification gap and the lack of diffusion during the solidification process. Additionally, primary and secondary precipitates were reported in both matrices in all three alloy conditions, while a local supersaturation of Al and Ti in the Ni-rich matrix, gradually led to the formation of metastable discontinuous cellular L12 precipitates close to the initial grain boundaries, which in turn underwent a destabilization and brittle Heusler phases of L21 structure most probably formed at the grain boundaries. To conclude, the maximum micro-hardness value found at 90 min of aging time was attributed to the precipitation shearing mechanism in both matrix areas, while an intermediate hardness value at 160 h aging time could be the result of the main strengthening mechanism change from shearing to Orowan.

Degree

thesis:*
Grantor dc:publisher
University of Ioannina
Year dc:date
2021

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Mathiou, Christina
  • Μαθιού, Χριστίνα

Subjects

dc:subject × 16

Rights

Language dc:language
eng

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/50074

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Mathiou, Christina; Μαθιού, Χριστίνα. Development and characterisation of new high entropy alloy systems of dual and/or multiple phases. University of Ioannina, 2021. http://hdl.handle.net/10442/hedi/50074