Institutes outside Greece
Battery emulator operating in a power hardware-in-the-loop simulation: the concept of hybrid battery emulator
Abstract
dc:descriptionThis thesis presents the design and implementation of a Battery Emulator (BE) operating in a Power Hardware-in-the-Loop Simulation and introduces the concept of the Hybrid Battery Emulator (H-BE). There are three major research areas: battery modelling, battery monitoring algorithms and power interface of the device implementing the emulator. Findings from all these areas are combined in the Hybrid Battery Emulator. Three battery models are implemented and compared: the Equivalent Circuit (ECM), the Kinetic (KiBaM) and the Diffusion. The comparison shows that the Diffusion model requires much higher computational power and thus, it is less suitable for a real-time application. Concerning the other two, the KiBaM is simpler to configure but the ECM exhibits higher simulation accuracy. The conducted sensitivity analysis reveals that the most important parameter for simulation accuracy is the state-ofcharge (SoC). The method proposed to increase the SoC accuracy is a Sliding Mode Observer, which compares the measured voltage from a real cell with the one estimated by the battery model, and adjusts the SoC accordingly.In order to demonstrate the potential of this application, an off-the-shelf power supply is used for implementing the BE. A stability analysis is conducted revealing that a series resistor has to be connected at the output of the power supply, and the conditions that this resistor has to obey are derived.Two implementations of the Hybrid Battery Emulator are shown. In both of them, a single cell of the battery pack is connected in series with the power device emulating the remaining cells. In the first implementation, a battery model provides the reference voltage to the power supply, and measurements from the real cell are used for updating the model parameters. The experiments reveal that the SoC errors are reduced and that the emulation accuracy is considerably increased. In the second method, there is no battery model. The real cell voltage is measured, multiplied and set as a reference to the power supply. This implementation exhibits higher accuracy but it is not suggested because it provides no information on the battery status. Finally, an alternative H-BE implementation is suggested for future work in which, the real cell is operated in a parallel experiment with a scaled-down current.
Degree
thesis:*- Grantor dc:publisher
- Institutes outside Greece
- Year dc:date
- 2017
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Daniil, Nikolaos
- Δανιήλ, Νικόλαος
Subjects
dc:subject × 32- Περιβάλλον προσομοίωσης ισχύος
- Υβριδικός εξομοιωτής μπαταριών
- Μοντελοποίηση μπαταριών
- Αλγόριθμοι παρακολούθησης της μπαταρίας
- Διεπαφή ισχύος
- Μοντέλο ισοδύναμου κυκλώματος μπαταρίας
- Κινητικό μοντέλο μπαταρίας
- Μοντέλο διάχυσης μπαταρίας
- Παρατηρητής λειτουργίας ολίσθησης
- Προσδιορισμός επιπέδου φόρτισης μπαταριών
- Ανάλυση ευστάθειας
- Ανάλυση ευαισθησίας παραμέτρων μοντέλου μπαταρίας
- Ακρίβεια εξομοίωσης
- Power hardware-in-the-loop simulation
- Hybrid battery emulator
- Battery modeling
- Battery monitoring algorithms
- Power interface
- Equivalent circuit model
- Kinetic battery model
- Diffusion model
- Sliding mode observer
- Battery state of charge estimation
- Stability analysis
- Model parameter sensitivity analysis
- Emulation accuracy
- Επιστήμη Ηλεκτρολόγου Μηχανικού, Ηλεκτρονικού Μηχανικού, Μηχανικού Η/Υ
- Επιστήμες Μηχανικού και Τεχνολογία
- Ηλεκτρική και Ηλεκτρονική μηχανική
- Electrical Engineering, Electronic Engineering, Information Engineering
- Engineering and Technology
- Electrical and Electronic Engineering
Rights
- Language dc:language
- eng
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/50416