Back to search

Aristotle University Of Thessaloniki (AUTH)

Κατασκευή κελυφών από νάνο σύνθετα υλικά σε 3D εκτυπωτή για ακραίες συνθήκες περιβάλλοντος

Abstract

dc:description

Global warming caused by increased amounts of greenhouse gases in the atmosphere has become an almost inevitable threat to human life, and adaptation strategies to climate change requires rapid reduction in carbon dioxide emissions. An extensive literature shows that the development and potential use of more sustainable, environmentally friendly building materials leads to a significant reduction in emissions of greenhouse gas pollutants from the construction sector. One of the most recent advances in the thermoplastic starch technology is the application of starch in the production of biodegradable plastics and construction biomaterials. This study has two main objectives: Firstly, to investigate the structure and physical and mechanical properties of natural (granular) and pregelatinized (non-granular) thermoplastic maize starch nanocomposite films and secondly to validate the feasibility and accuracy of a novel technique for the preparation of 3D – printed sandstone building materials that use gelatinized starch as a binder and sand as filler.In the present study, a simple solution method is employed for the preparation of maize starch-based films with tailor made tensile properties for various applications of biodegradable materials. The obtained intercalated nanocomposite microstructures are confirmed by the XRD technique and the tensile behaviour is investigated as a function of clay and glycerol contents. The best results are obtained with sodium montmorillonite nanocomposites (NaMMT) at glycerol concentration of about 20 wt% and clay content of about 10 wt%. Compared to other studies, the obtained nanocomposites show a higher increase in tensile strength, as it can be concluded from the above findings. Moreover, the experimental results indicated that the use of non-granular (pregel) starch enables the production of thermoplastic starch-clay biodegradable films with tailor made physical and mechanical properties depending on their glycerol as well as sodium montmorillonite (NaMMT- clay) particles content. The prepared non-granular thermoplastic starch – clay biodegradable films proved to be more uniform in texture than their counterparts prepared from granular starches, hence more reliable from the quality control point of view for future industrial applications.In the last decades there is an increasing interest in the development and potential use of biodegradable biopolymers from renewable sources and the gradual replacement of traditional building materials by low-cost natural polymeric materials used in the construction industry. One of the main objectives of this investigation was to validate the feasibility and accuracy of a preliminary method for the preparation of sand starch mortars that could possibly be an alternative technique for transition of the production process from laboratory to industrial scale. It can be concluded from the comparison with other techniques found in the literature that the presented procedure solves most of the problems associated with heating in microwave ovens. The physical and morphological characteristics of this type of solid product to a certain extent resemble the properties of a sandstone material that uses gelatinized starch as a binder and sand as filler, while exhibiting the thermoplastic mechanical behavior of polymer-matrix composite materials. The test results showed that this type of artificial starch-sandstones has a compressive strength of about 30 MPa with a ratio of tensile strength to compressive strength of approximately 0.20 and significantly low values of modulus of elasticity less than 2 GPa. Also, the effect of addition of nanoparticles on the physical and mechanical properties of this material was investigated and the behavior of the artificial starch-sandstones in extreme environmental conditions was studied. The experimental results showed a slight decrease in compressive strength with increasing temperature. However, the physical and mechanical properties of artificial sandstones are more negatively affected by moisture due to the hydrophilic nature of the starch and their extremely porous structure, as also confirmed by SEM images. Different preliminary methods of treatment were also applied using conventional and natural biodegradable coating compositions to increase the hydrophobicity of such starch-based construction materials, thereby decreasing the water adsorption capacity of the composites, gradually achieving complete waterproofing of the structures with desired durability properties for applications in the building and construction industry.The three-dimensional printing technology is a manufacturing process of creating physical 3D-objects through the successive addition of material in layers based on a computer aided design (CAD) technique. The 3D - printed artificial starch – sandstone material was found to have better mechanical and durability properties than in the 3D - printing of conventional concrete (3DPC). These findings can be easily attributed to the more uniform morphology and better 3D-printing layer to layer adhesion shown by the starch sandstones with respect to that of the conventional concrete.

Degree

thesis:*
Grantor dc:publisher
Aristotle University Of Thessaloniki (AUTH)
Year dc:date
2021

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Zoumaki, Maria
  • Ζουμάκη, Μαρία

Subjects

dc:subject × 12

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/50899

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Zoumaki, Maria; Ζουμάκη, Μαρία. Κατασκευή κελυφών από νάνο σύνθετα υλικά σε 3D εκτυπωτή για ακραίες συνθήκες περιβάλλοντος. Aristotle University Of Thessaloniki (AUTH), 2021. http://hdl.handle.net/10442/hedi/50899