National Technical University of Athens (NTUA)
Μέθοδοι πρόληψης αστοχιών στη τσιμέντωση γεωτρήσεων πετρελαίου
Abstract
dc:descriptionDifferent Parameters such as: the geomorphology in a given basin, the environmental conditions, the applicable standards and the methods and the construction efficiency of an Oilwell can affect the integrity of the cementation throughout the life of the Oil Well. As cementing is one of of the most important stages of an Oilwell, best practices should be used during cement casting, to achieve proper rheological performance for adequate zonal isolation and resistance to changes due to the extreme pressure and temperature condition during the operation. Subsequent failures can lead to significant social, environmental and economic consequences.The aim of the present dissertation is to study methods for avoiding these failures and ensuring the cementing of Oilwells and the better understanding of the effects, related to the initial composition of the cement and the final properties of the hardened slurry, due to the use of additives and the different pressure temperature conditions in the Oilwell.Initially, the design logic of the special type of cement API 10A CLASS G is developed which is widely used and suitable for cementing operations at great depths with High Resistance to Sulphates capabilities. After the selection of proper raw materials (eg. low in alkali and low C3A content) and by using best production practices (drying, granulometry control and firing conditions) the produced clinker was grinded with dihydrate (CaSO4.2H2O) and studied according to the methods described in the standard API 10A. The performance of the Laboratory produced Cement (LAB) corresponds to the API 10A Class G HSR Oilwell Cement. The same tests were performed on another commercially available Class G HSR cement (COM), with different initial composition and a comparative study was performed based on API 10A and to investigate the hydration reactions of the two cements and their products.For the assessment of pumpability, thickening time is one of the key performance parameters as described by API 10A and 10B. To measure it, a Consistometer is used, where the slurry is continuously stirred in an autoclaved container, with simultaneous change of pressure and temperature conditions. When the mixture is no longer miscible, the thickening time is recorded. To regulate this parameter, slurries with different retarder concentrations were studied, by measuring thickening time under High Temperature/ High pressure Conditions. It was observed that with small changes in the content of the retarder, a significant increase in the thickening time was observed. After selecting the retarder concentration which corresponds to specific thickening time performance, the combined effect of constant concentrations of widely used additives (fluid loss regulators, dispersion and foaming regulators) was studied to investigate potential synergistic / antagonistic effects of the additives at the same HT/HP conditions. As it turns out the combined use of additives can have a significant effect on the final thickening time regardless of intended use of the additive, due to synergistic / competitive actions and there is need for experimental evaluation especially in mixtures with different additives and the HT/HP conditions can affect the hydration rate of the cement and the behavior of the additives in the slurry. As alternative to experimental evaluation a computational study of the thickening time was performed to investigate the correlation of the final properties (thickening time) of Oilwell cement with initial properties of dry cement, using machine learning techniques. For this study, a database was constructed from 230 oil well cements, which were collected by the industry (daily production results - daily averages of samples performed by the desired chemical analyzes, physical and mechanical measurements). The correlation between measurable properties of unhydrated cement and its final performance was achieved and It was confirmed that the physicochemical parameters can be used as a qualitative signature of each cement. During the first periods of cement hydration, High temperature conditions can lead to the development of cracks associated with chemical reactions or fluctuations in heat and humidity. For the better monitoring of the rate of hydration of the Oilwell Cements, test were performed on slurries consisted of laboratory produced Oil Well cement (LAB) and Phase Change Materials, i.e. Materials that go into a different phase -from solid to liquid, or vice versa- absorbing or releasing latent heat from / to the environment. The reduction of the temperature increase due to hydration of the Oilwell cement can be achieved by replacing part of the cement with additional cementitious materials that produce less heat. The use of different Phase Change Materials (PCMs) can lead to controlling the temperature rise of oil well cement due to their ability to store thermal energy. Melting point, fusion heat, density, thermal capacity, thermal conductivity, chemical compatibility and production cost are the main parameters for selecting the most suitable PCM. Tests were performed with curing of the specimens in two different curing conditions (ambient and partially in HT/HP conditions). With the use of this materials, the reduction of the maximum temperature and the control of the hydration rate was achieved, but with a significant effect on the properties of the hardened pulp, especially in HT/HP conditions.
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2022
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Velissariou, Dimitrios
- Βελισσαρίου, Δημήτριος
Subjects
dc:subject × 20- Τσιμέντα Γεωτρήσεων Πετρελαίου
- Ενυδάτωση τσιμέντου
- Χρόνος Πάχυνσης
- Υλικά αλλαγής φάσης
- Μηχανική μάθηση
- Oil Well Cements
- Cement hydration
- Thickening Time
- Phase change materials
- Machine learning
- Επιστήμη Χημικού Μηχανικού
- Επιστήμες Μηχανικού και Τεχνολογία
- Χημεία και Τεχνολογία διεργασιών
- Μηχανική Υλικών
- Επιστήμη υλικών, γενικά
- Chemical Engineering
- Engineering and Technology
- Process Chemistry and Technology
- Materials Engineering
- Materials science, general
Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/51446