National Technical University of Athens (NTUA)
Integrated processes for turbocharger design and retrofitting
Abstract
dc:descriptionThe thesis is concerned with the development of integrated processes for turbocharger(T/C) design and retrofitting. The processes, developed with three modes of operation, provide a fully automatic retrofit and design solution or the option for T/Ced Diesel Engine Simulation.The first process which corresponds to turbocharged(T/Ced) diesel engine simulation, utilizes 1D meanline models for T/C components, a single-zone model for the diesel engine and a T/C-diesel engine matching analysis. The diesel engine model is adapted to engine-specific data and the overall integrated model is validated against shop trials data, obtained from a marine diesel auxiliary engine. A physically consistent, transparent, and fully automated procedure is integrated in each turbo-component meanline model, for producing the corresponding performance map. Additionally, turbine meanline model(axial and radial) is developed with the ability to compute turbine performance beyond choke limit, allowing the prediction of T/C operation with choked turbine.The second process refers to T/C preliminary design. An optimization procedure is employed, to design both compressor and turbine to match the entire T/Ced system. The optimization process focuses on engine fuel consumption reduction in the engine range of operation, while ensuring appropriate matching between turbomachinery components and the diesel engine. Structural integrity of both turbo-components is ensured by using simplified static and modal analysis. Dimensionless parameters are used as optimization variables, for both compressor and turbine, providing a more general and automated design process since there is no need to redefine the range of optimization variables and the initial geometry for different T/C scales. It also produces four improved 1D geometries, of different possible centrifugal compressor diffuser and turbine combination. The combination that gives the best improvement to the diesel engine operation is identified. Additionally, partial turbo-component design option is provided. Similar to the entire T/C design procedure, a 1D turbo-component multi-point design optimization process is carried out, aiming to provide a fast and reliable solution based on T/Ced diesel engine range of operation. Structural integrity is also ensured by using simplified structural analysis. For compressor design, a CFD compressor multi-point design optimization process is also provided, producing an improved 3D compressor geometry. It complies with the T/Ced diesel engine range of operation, while structural integrity is ensured by using Finite Element analysis.The last process corresponds to automatic T/C retrofitting. During this process, available turbo-components are examined, in order to select the one that best matches the entire engine system, aiming to retain or improve the diesel engine efficiency.Then, the above procedures are then applied to two application test cases. In the first one, a T/C redesign-retrofit case study is presented, where four retrofitting options are analyzed (compressor replaced, T/C replaced, compressor redesign and entire T/C redesign). In the first and second option, T/C retrofitting is carried out, using available turbo-components. It is shown that initial performance cannot be reconstituted using off-the-self solutions. In the third option, a T/C compressor redesign is carried out. First, a T/C 1D compressor design is performed, aiming to at least reconstituting the original diesel engine performance, providing a reliable compressor initial geometry for the 3D design procedure. Then, a fully 3D compressor design is then performed, using a CFD-FEA optimization process, in order to provide an improved retrofitting solution.In the fourth option, where the entire T/C is redesigned, all four T/C configurations are designed and analyzed aiming to at least reconstituting the original diesel engine performance. All four improved T/C geometries are sorted based on the diesel engine annual fuel cost reduction. Finally, a techno-economical assessment is carried out, analyzing all four retrofit options economic performance. In the second case, specific faults are simulated, utilizing physical consistent parameters such as blade roughness and thickness based on relevant literature data. Overall system simulation and operation analysis is carried out assessing operability and performance parameters. Analysis results show a significant reduction in engine performance, especially in case of both turbo components being fouled, in contrast with the heat exchanger fouling where the power reduction is less affected.
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2022
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Ntonas, Konstantinos
- Ντόνας, Κωνσταντίνος
Subjects
dc:subject × 31- Στροβιλοϋπερπληρωτής
- Βέλτιστος σχεδιασμός
- Αριθμητικές υπολογιστικές τεχνικές
- Αντοχή
- Ταλαντώσεις
- Ρευστοδυναμική, υπολογιστική
- Ρευστοδυναμική
- Μοντέλα μέσης γραμμής
- Τεχνιτή νοημοσύνη
- Μηχανές εσωτερικής καύσης
- Turbocharger
- Turbocharger simulation
- Turbocharger retrofit
- Turbocharger design
- Meanline model analysis
- Computational fluid dynamics
- Finite element analysis
- Modal analysis
- Internal combustion engines
- Automotive and marine diesel
- Diesel Engine single zone model
- Artificial intelligence
- Adaptive optimization
- Επιστήμη Μηχανολόγου Μηχανικού
- Επιστήμες Μηχανικού και Τεχνολογία
- Μηχανολογία
- Αεροδιαστημική μηχανική
- Mechanical Engineering
- Engineering and Technology
- Mechanics
- Aerospace Engineering
Rights
- Language dc:language
- eng
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/54086