National Technical University of Athens (NTUA)
Βελτιστοποίηση της μικροδομής ελασμάτων αλουμινίου για εφαρμογές υψηλής προστιθέμενης αξίας
Abstract
dc:descriptionThe current Doctoral Thesis deals with the evolution of the crystallographic texture during the rolling process. More specifically, it looks into the effect of the specific thermomechanical processes on the final product properties through the development of the crystallographic texture. The aim was to master the evolution of the crystallographic texture during the rolling process and to enable the set of desirable and predictable properties in the manufactured final product. Initially, non-heat-treatable aluminum alloys, namely the 3104 and 5182 Al alloys that essentially share a very large portion of the relevant market were studied. Focus was laid on their chemical composition, mainly with regard to the magnesium and manganese content as well as the effect of second phase particles on texture evolution. Furthermore, possible effects of the applicable production process such as the hot rolling mill type (Hot Tandem Mill - Hot Reversing & Coiling Mill) were thoroughly studied. Process related parameters affect the final rolling & coiling temperature influencing the developed texture. Similarly, the effects on the texture of the recovery, recrystallization and baking heat treatments were also studied. The hot rolled sheet in the case of the Hot Reversing & Coiling Mill resulted in a microstructure dominated by deformed grains, while some recrystallized ones were present, a result accompanied by a correspondingly strong deformation texture (β fiber). In the case of the hot rolled sheet produced by Hot Tandem Mill, the microstructure was largely recrystallized and equiaxed with a predominant recrystallization texture (Cube, Cube-RD). This difference resulted in the final product produced with Hot Tandem Mill showing better anisotropic behavior (Z = 2.66) compared to the hot band produced with Hot Reversing & Coiling Mill (Z = 2.98). Towards that direction, samples with different cold rolling reduction percentages were studied, in relation to plastic deformation as well as the effect of axial loading on grain orientation. It should be noted that the aforementioned examinations were conducted using EBSD analysis for which an appropriate methodology was developed. In particular, the possible nucleation points of new grains in the microstructure were identified along with the relevant adjacent grain orientations, that would significantly affect the orientation of new nuclei. As such the effects of cold rolling reduction percentage and the subsequent heat treatment stages were studied and considered in relation to the observed type and quantities of the desirable crystallographic components. Based on the aforementioned findings an experimental cold rolling process was designed and implemented for the production of a product containing an optimal amount of rolling and recrystallization texture components that would result in the desirable mechanical properties for the given application. The hot band produced by the Hot Tandem Mill was selected as the starting sheet for the further study. This enables for even better anisotropy after the proper design and control of the texture. The rolling parameter that was decided to be modified was the reduction rate. In addition, the final stage of the recovery annealing was altered mainly by avoiding the final annealing stage. The final sheet acquired better properties than have been achieved with the previous production process steps. Significant differences were observed between the samples of the different cold-rolled designs, both industrial and experimental, in terms of the evolution of the microstructure and the crystallographic texture, but also in relation to the mechanical properties and anisotropy of the final product. The main influencing parameter was the end roll temperature. The crystallographic texture was fully controlled. The texture obtained the lowest possible anisotropy (Z=1.68). At the same time, using the developed methodology as a reverse engineering process, we confirmed the ability to identify the critical noticeable differences in the texture of semi-finished and/or finished products. This methodology allows to draw important conclusions just by analyzing the texture revealing information about the product’s critical production stages. Additionally, knowing these texture details one can predict the behavior of the material in the further forming steps (e.g. deep drawing) . Thus, not only can the desired texture can be produced but also the production conditions (in terms of critical parameters) of an unknown semi-finished or finished product can be assessed.
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2022
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Papadopoulou, Sofia
- Παπαδοπούλου, Σοφία
Subjects
dc:subject × 21- Κρυσταλλογραφικός προσανατολισμός
- Αλουμίνιο
- Μικροδομή
- Θερμομηχανικός έλεγχος
- Έλαση
- Θερμικές κατεργασίες
- Crystallographic orientation
- Aluminum
- Microstructure
- Thermomechanical control
- Rolling
- Annealing
- Thermal treatments
- Μηχανική Υλικών
- Επιστήμες Μηχανικού και Τεχνολογία
- Επιστήμη υλικών, χαρακτηρισμός και δοκιμές
- Μέταλλα και Κράματα
- Materials Engineering
- Engineering and Technology
- Materials Science, Characterization and testing
- Metals and Alloys
Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/54253