University of Patras
Επεξεργασία λυμάτων με μικροφύκη σε διατάξεις προσκολλημένης βιομάζας
Abstract
dc:descriptionThe photosynthetic growth of microalgae requires light, CO2, water, and minerals. Microalgae have the ability to produce O2 and contribute to the reduction of the greenhouse effect. The most common method of cultivation is suspended culture, where the biomass is suspended in liquid and the final concentration of microalgae is relatively low. More specifically, the biomass concentration ranges from 0.1 to 1 g/L (i.e., 0.01 to 0.1%) (Johnson and Wen, 2010). Biomass harvesting is an extremely expensive process and is usually done through filtration, flotation, flocculation, sedimentation, and centrifugation, which are energy-intensive processes. The small size of the cells (2 to 40 µm) makes the harvesting process even more difficult (Lin-Lan et al., 2018). Biofilm cultures can overcome the high costs associated with harvesting the algae and have a productivity of 10 to 20% higher than that which can come from simple centrifugation. The purpose of this dissertation was the investigation of biofilm development and, more specifically, the examination of the physicochemical parameters that affect the adhesion of microalgae to various materials for wastewater treatment, with the ultimate goal of constructing a biofilm bioreactor with the most efficient materials. The reactor will have the capacity to treat wastewater, remove nitrogen, phosphorus, and organic material, and produce sufficient microalgal biomass for further utilization as an alternative energy source (biodiesel). or biopolymers such as lipids, total proteins, and carbohydrates. Regarding the selection of suitable microalgae support materials and the investigation of factors influencing biofilm growth, materials with different properties were selected: wettex, cork, cotton denim, stainless steel, rubber, geotextile, plexiglas, glass, plexiglas patterned in three different ways (plexiglas 1, 2 and 3) and glass reinforced with polymeric brass fibers and glass fibers. More specifically, all materials were cut in the form of coupons (7.4×2.4×0.1 cm, L×W×H) in horizontal or vertical orientation and placed in laboratory-scale tanks under continuous nutrient supply with an experimental period of 16 days. The strains of microalgae studied were Scenedesmus rubescens, Chlorococcum sp., Botryococcus braunii, Neochloris vigensis, and mixotrophic algae, which came from the tank of the wastewater treatment plant of the University of Patras campus at Rio. The physicochemical properties of the materials examined included the contact angle, surface energy, acid-base interactions, Lifshitz-van der Waals interaction forces, the point of zero charge, and the surface groups with ATR-FTIR (attenuated total reflection-fourier transform infrared spectroscopy). The various biochemical parameters examined were: pH, optical density (OD650), turbidity, anions (PO43--P, NO3--N), cell number, zeta potential, chlorophyll-a (chl-a), lipids, total proteins, and carbohydrates. The interaction of the biofilm of the examined microalgae with the surface of the coupons was captured by scanning electron microscopy (SEM) analysis. The results showed that the hydrophobicity of a material does not play a decisive role in adhesion, as hydrophobic microalgal strains adhered to hydrophobic materials and vice versa. Accordingly, contact angle, surface energy, or PZC, and surface groups do not appear to predict the adhesion performance of materials. Micropatterning does not enhance the performance of materials in terms of biomass production. The microalgae strain plays a decisive role in the attachment process, due to selectivity. Fibrous materials, visually, appear to be effective. However, this cannot be quantified as there is either loss of material due to biodegradation or corruption. However, the surfaces, despite the detachment, were again productive over time, during cultivation. Subsequently, a pilot-scale photobioreactor was constructed with two different support materials: plexiglas and wettex. The photoreactor is oriented vertically, and the surfaces are placed on an appropriate slope (20°) to support the microalgae. The reactor was evaluated for its effectiveness in nutrient (nitrogen and phosphorus) and organic material removal, as well as biomass production, through bacteria-microalgae symbiotic action in primary settled wastewater. The cycles of experiments for the bioreactor with wettex were two and lasted 50 d and 16 d, while the bioreactor with plexiglas lasted 42 d. The reactor performance was monitored by measuring the following parameters: pH, OD650, turbidity, NO3--N, total and soluble phosphorus (Total P and sTotal P), chemical oxygen demand (COD) and soluble COD (sCOD), ammonium nitrogen (NH3-N), total Kjeldahl nitrogen (TKN), lipids, total proteins, and carbohydrates. Both the plexiglas photobioreactor and the wettex photobioreactor were effective in removing NO3--N, NH3-N, TKN, Total P and COD from the wastewater, while when the recirculation rate was reduced, the efficiencies were even higher, and this was due to the longer contact period between the wastewater nutrient and the attached microalgae. In the plexiglas photobioreactor, during the second harvest, biofilm production was almost 42% higher than the first harvest. The lower recirculation supply, combined with not scraping the biomass at the end of the 1st harvest, were positive contributing factors. Microalgae have the ability to produce triglycerols (TAGs) and are considered a second-generation raw material in the production of biofuels, specifically biodiesel. The lipids of the microalgae Chlorococcum sp. (cultivated in secondary treated wastewater) and Scenedesmus rubescens (cultivated in BG 11-1/3 NO3-) were converted to methyl esters (biodiesel) via transesterification. Homogeneous catalysts H2SO4, NaOH were used in the one-step method and in a combination method using first NaOH and then H2SO4 (two steps). Subsequently, the biomass of Scenedesmus rubescens microalgae, cultivated in 1/3 NO3--BG 11, was examined. After extraction of the lipids, transesterification with biochar followed. The biochar was derived from malt roots, which were pyrolyzed at 850°C for 3 hours. Then, the performance of the modified biochar with H2SO4 1 N was also examined. The physicochemical properties of the catalyst were determined, and its ability to convert lipids into biodiesel was examined. Finally, the performance in the production of methyl esters from biochar catalysts, produced from malt spent rootlets, spent coffee grounds, and olive kernels, pyrolized at 400 and 850oC for 3 hours, was examined. In conclusion, the choice of the type of the catalyst depends on the FFA content of microalgae lipids. The variety of methyl esters highly depends on the type of microalgae species and their growth conditions. The catalyst from spent coffe grounds pyrolyzed at 400°C was found to be equally effective as H2SO4 and NaOH.
Degree
thesis:*- Grantor dc:publisher
- University of Patras
- Year dc:date
- 2023
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Tsavatopoulou, Vasiliki
- Τσαβατοπούλου, Βασιλική
Subjects
dc:subject × 10Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/55168