National Technical University of Athens (NTUA)
Ανάπτυξη πολυμερικών συστημάτων μορφολογίας καψουλών μέσω διεργασιών πολυμερισμού
Abstract
dc:descriptionEncapsulation of active ingredients represents an innovative technological field, where multiple properties can be combined within a system. This doctoral thesis aimed at studying encapsulation techniques for the development of polymeric capsules (core-shell morphology), with self-healing and self-lubrication selected as application areas. Self-healing systems have lately attracted research interest because, inspired by nature, they have the ability to autonomously detect and repair damage, without external intervention. As a result, the risk of material failure is significantly reduced, and the need for maintenance and associated costs decrease rapidly. In this context, the use of polymeric microcapsules for self-healing applications in protective coatings on metallic surfaces was investigated. More specifically, the development of poly(urea-formaldehyde) (PUF) microcapsules with an encapsulated epoxy resin (DGEBA), through in situ polymerization was chosen for investigation. Initially, the effect of critical in situ polymerization parameters on the properties of the produced microcapsules was examined. The core: wall mass ratio, the geometry of the stirring blade, the stirring rate during mechanical agitation, the use of a homogenizer at various stirring rates, the pH, and the concentration of the emulsifier were correlated with the final properties of the capsules (size, morphology, encapsulation efficiency, chemical structure, and thermal properties). As the microcapsules studied were to be used in self-healing coating applications, where capsule size and morphology is of vital importance, the objective set was to produce microcapsules with a high encapsulation efficiency (>70%), mean size less than 50 µm, with a free-flowing powder morphology, features enabling their incorporation into coatings. In parallel, the feasibility of transferring the developed systems to the industry was studied, therefore the parameters which may obstruct the industrialization were determined and analyzed. For the most promising sample, with the desired properties, the reproducibility of in situ polymerization process and the stability of the capsules during storage were further examined. Subsequently, alkyd-based coatings were developed, by incorporating microcapsules along with the appropriate curing agent (ethylenediamine-EDA) for the encapsulated epoxy resin. The coatings’ morphological characteristics were studied, along with surface properties such as roughness, gloss, and König hardness. These properties were correlated with the microcapsule content in the different coatings (5, 10, 15% w/w). The introduction of microcapsules at all concentrations led to increased surface roughness, while in the case of the highest concentration (15% w/w) the formation of microscopic pores was observed through SEM microscopy. As a result, its protective properties were inferior compared to the reference coating without capsules, as supported by electrochemical impedance spectroscopy (EIS) measurements, which were used to assess the self-healing properties after manually creating scratches on the coatings. On the contrary, lower concentrations (5 και 10 % w/w) led to a slowdown in the corrosion of the metallic substrate, especially in the case of 5% w/w. SEM images confirmed the formation of a protective layer at the site of the initially exposed substrate. In collaboration with Chrotex S.A., a leading Greek company operating in the paint industry, additional tests were conducted on self-healing coating systems based on microcapsules. Both alkyd-based and epoxy-based protective coating systems for metal surfaces were tested. Furthermore, the incorporation of microcapsules into the topcoat layer, the primer layer, and a combination of both (multilayer system) were examined. In the case of the multilayer coating system, the capsules were incorporated into the primer, and then the topcoat was applied. For the successful and uniform dispersion of the capsules within the paint, while minimizing the risk of breaking their shell, mechanical mixing was employed and parameters such as the type of the agitator, the stirring rate and duration were examined. Afterwards, the application of the produced coatings on metallic substrates for their evaluation was carried out, using the air spray technique. In the case of alkyd-based paints, the introduction of the self-healing system (microcapsules and EDA curing agent) led to increased roughness and reduced König hardness. Additionally, in the case of introducing the system in the topcoat, the curing agent caused a change in color, and the drying time increased, when compared to the reference coating. On the other hand, the multilayer system (primer and topcoat) did not exhibit significant macroscopic differences from the corresponding reference sample, although König hardness was again reduced. The self-healing properties of the coatings, after the scratch formation, were evaluated at ambient conditions, at controlled temperature conditions (50°C), as well as in a corrosive environment (salt spray test). Examining the morphology of the scratch after 7 days using optical microscopy, under the first two conditions, the formation of a protective coating was observed in all cases of coatings containing microcapsules. On the contrary, the self-healing coatings did not exhibit satisfactory performance in the corrosive conditions of the salt spray chamber, which was attributed to the significantly reduced hardness of the coatings. Epoxy-based coatings are two-part paints consisting of the paint resin and the appropriate curing agent. In this case, the use of EDA was not necessary, a significant advantage over the alkyd-based coatings. Similar to the alkyd coatings, the incorporation of microcapsules into the topcoat and primer affected the surface morphology, introducing roughness and reducing hardness. On the other hand, the multilayer system (primer and topcoat) did not present any significant difference, compared to the reference sample. That resulted in very good performance in the salt spray conditions; after 400 h of exposure, the reference sample exhibited significant corrosion, while the self-healing system within the coating had successfully protected the substrate. The self-healing properties of the system were also confirmed through EIS, where a significant delay in corrosion was observed compared to the reference sample. Also, SEM microscopy verified the formation of a protective layer in the once exposed area. The second application sector within this doctoral dissertation involved studying microcapsules for self-lubricating coatings application. Lubrication is an integral part of the smooth operation of any system, but traditional techniques have limitations. By incorporating a self-lubricating mechanism into a system, it is possible to simultaneously reduce friction and wear, decreasing the maintenance requirements, significantly reducing costs. The development of cermet coatings via thermal spray with self-lubricating properties based on microcapsules was examined. Ultimately, the goal was to apply these advanced coatings on piston rings of diesel marine engines to reduce losses due to friction. More specifically, the encapsulation of a commercial lubricating oil in a poly(urea-formaldehyde) shell through in situ polymerization was studied. Similar to the self-healing system, the impact of critical parameters (core: wall mass ratio, mechanical stirring rate, emulsifier concentration), on the properties of the capsules, were examined. The primary objective was to improve the thermal stability (T5% > 300°C) of the PUF capsules, so as to withstand the high temperatures developed during the thermal spray technique. In all cases, the formation of capsules was limited due to extensive PUF precipitation. Furthermore, the reproducibility study of in situ polymerization in this case did not yield satisfactory results. Therefore, an alternative microcapsule system based on polysulfone (PSF) with encapsulated lubricating oil was developed using the emulsification-solvent evaporation technique. The choice of this system was based on the high thermal stability of polysulfone (Td>500°C). Parameters studied in the process included core: wall mass ratio, mechanical agitation stirring rate, viscosity of the core material, and the use of a homogenizer at various rates during the emulsification stage. Ultimately, two types of microcapsules were obtained, differing in size and encapsulation efficiency, and their scaling up potential was examined. The tests were deemed successful, since production of microcapsules with similar properties was conducted on a larger scale (400 mL/20 g of capsules) compared to the initial 35 mL scale (1 g of capsules).Subsequently, thermal spray tests were conducted by the research and technology center EBETAM S.A. as part of a research cooperation. Initially, the technique was modified to introduce the capsules in the form of an aqueous dispersion, at a distance from the plasma flame, to limit the thermal stress on the capsules. Tests were then carried out, using a variety of cermet materials as matrices, simultaneously controlling critical parameters of the technique (material supply, spray distance, spray velocity, etc.). Afterwards, the morphology, mechanical properties and tribological properties of the developed composite coatings were evaluated. Through SEM microscopy, the successful incorporation of the microcapsules within the cermet coatings was verified which led to significantly reduced coefficient of friction (up to 59 %) and wear (up to -94 %) in all cases of composite coatings, highlighting the self-lubrication properties of the developed system. Finally, the most promising coating was successfully applied, in real operating conditions, on piston rings within a diesel marine engine.
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2023
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Zotiadis, Christos
- Ζωτιάδης, Χρήστος
Subjects
dc:subject × 13Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/55335