Back to search

University of Patras

Ανάπτυξη, χαρακτηρισμός και έλεγχος λειτουργικότητας σύνθετων πολυμερικών υμενίων βασισμένων σε νανοδομές άνθρακα

Abstract

dc:description

The PhD thesis focuses on the development of “breathable” membranes based on polyolefinic nanocomposites. "Breathable" membranes are usually produced by incorporating micro/nanofillers, such as CaCO3, which interrupt the continuity of the polymeric phase and when subjected to uniaxial or biaxial stretching this process leads to the formation of microporous structures. It has also been shown that the growth of the β-phase in isotactic polypropylene (i-PP), in the presence of a nucleating agent and in combination with the stretching process can also lead to the production of microporous films, which allow water vapor diffusion.1D (CNTs) and 2D (GO, rGO, GNPs) carbon nanostructures alone or in combination with a β-nucleating agent (β-NA) are an alternative type of fillers proposed for the development of "breathable" polypropylene membranes. "Breathable" composite polymer films can be applied either (i) as building roof membranes, which allow water vapor to permeate through and avoid moisture build-up, and/or (ii) as moisture control membranes, capable of preventing the water vapor produced in the building to diffuse freely towards the ceiling (wall, floor) and to minimize heat loss through convection. The main objective of this Doctoral Thesis was to study:(a) the water vapor permeation property of composite PP polymeric films, containing various proportions of β-NA and carbon nanostructured inclusions (MWCNTs, GO, rGO, GNPs).(b) as well as the main factors affecting the “breathability” property of a polymer film in the absence of stretching, such as (i) the different crystallization mode (cooling rate) applied during the preparation of the composite film, (ii) the percentage of the crystalline phases of the polymer, (iii) the types of inclusions (1D and 2D carbon nanostructures with different characteristics) used and (iv) the different process of their production (laboratory, pilot, industrial scale).The characterization and study of the properties of the new composite polymer films were carried out through corresponding techniques. Specifically, their thermal properties were studied using the Differential Scanning Calorimetry (DSC) technique, while the study of their structure and crystalline behavior was done via X-ray Diffraction (XRD). Their morphological characterization was performed with scanning electron microscope (SEM) images. For the thermal characterization of the carbon nanostructures, the thermogravimetric analysis (TGA) was used. For their chemical and structural characterization, in addition to the XRD technique, micro-Raman spectroscopy, ATR/FTIR, as well as X-ray photoelectron spectroscopy (XPS) were utilized. Additionally, the functionilized carbon nanotubes (MWCNT-g-PP) as well as the GOs, which were used as nanoinclusions in the preparation of the composite PP polymeric films, were studied for their potential cytotoxicity through in vitro exposure and for their potential release into the environment. The "breathability" properties of the composite polymeric films were evaluated by water vapor diffusion measurements in a controlled humidity laboratory setup, according to the "wet cup method". All nanocomposite polymer films produced on a laboratory scale were compared with pilot-type & commercial-type films, manufactured PLASTIKA KRITIS S.A. and by Thrace Polyfilms SA (a company of the Thrace Plastics group), respectively. It was observed that hybrid nanocomposites containing MWCNT-g-PP and β-NA presented enhanced water vapor permeability values compared to the nanocomposites containing only one of these inclusions. Furthermore, for these hybrid nanocomposites, thermal annealing was shown to be more effective for increasing the β-crystalline phase, and at the same time for further enhancing the water vapor permeability values. Regarding the study of 2D nanocarbons as inclusions, it was observed that all hybrid nanocomposite films PP/x% β-NA/y% 2D nanomaterials (GO, rGO and GNPs), presented enhanced water vapor permeability values, compared to the values of the films of the polymeric matrix. Also, all PP/GO, PP/rGO, PP/GNPs nanocomposite films, with and without β-NA, showed a maximum water vapor transmission value at a percentage of graphitic nanoinclusions of 1.5%, with water vapor transmission values (Sp.WVTR) up to and above 7000 μm g/m2 day, which allows their use at least as humidity control membranes.

Degree

thesis:*
Grantor dc:publisher
University of Patras
Year dc:date
2024

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Visvini, Glykeria
  • Βισβίνη, Γλυκερία

Subjects

dc:subject × 24

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/56723

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Visvini, Glykeria; Βισβίνη, Γλυκερία. Ανάπτυξη, χαρακτηρισμός και έλεγχος λειτουργικότητας σύνθετων πολυμερικών υμενίων βασισμένων σε νανοδομές άνθρακα. University of Patras, 2024. http://hdl.handle.net/10442/hedi/56723