National Technical University of Athens (NTUA)
Καταστροφικές καταπονήσεις οχημάτων: η περίπτωση των ανθρακονημάτινων σκελετών αγωνιστικών ποδηλάτων δρόμου
Abstract
dc:descriptionTime flows like a river and the world changes! So do humanity’s needs and priorities. New technologies, new inventions and research is conducted for the creation of new products and materials, in order to satisfy our current and future needs. One of these materials is carbon fibers, whose use and applications will be part of this thesis. In recent years, carbon fibers have been widely used for the construction of components which are not limited to the standard sectors for them: Defense Equipment, Aerospace Industry and Motor Sports. They have become common in everyday use products, in all types of vehicles, as well as bicycles, especially Road Racing Bikes. From our research it has emerged that although the carbon fiber frames are widely used, they fail easily if they receive a load that is slightly different from what is prescribed by the safety standards. Despite the careful design and high quality of their construction, there are failures, resulting both from falls and from the fact that the frames designed and built with the rules of the "Aircraft Engineer" who follows the directions of the Marketing Department, they are very rigid and generally fragile. On the other hand, driving in unpredictable situations, for example potholes, traffic and bad weather conditions, worsens the problem of failures. Regarding their price, they have a very high cost because they use design and manufacturing methods from the Aviation industry, where specialized engineers and expensive software are required. Also in the Manufacturing part, very expensive equipment is used (autoclaves or presses with heated plates as well as special molds are required for production).These failures increase the cost of ownership for their users, since their replacement is both costly and time-consuming because constant development and marketing make it difficult to find spare parts. In this thesis, a new design and manufacturing method for road bicycle frames is proposed and developed in order to reduce the cost and the number of broken frames. Specifically, the design and analysis method that was developed is the following: After thinking about the structure we want to make, we design and study its parts independently in torsional and bending stiffness as well as in aerodynamic behavior if required and then we combine them and conduct the least possible tests to them. The study of the laminate is taking place in the final design stage where we regulate the strength and behavior of our construction through it. In this way we save the costly process of redesigning entire models and the time-consuming changes of their sub cases that would be required if we designed and studied in each scenario an entire model. In addition, this method allows us to create a database for future use and easy development of new sub-variants of the construction. In the bike frame in our case, we studied various possible shapes in each tube in both aerodynamic behavior and stiffness and chose a shape for each tube. Then we combined them and created the final model which we studied as an overall model for the final verification. This process not only saved us a lot of time in the design part, but also gave us the possibility to make very easy sub-variations, such as different sizes. The advantages include the easy creation of new models with different characteristics since we have a database ready with qualitative and quantitative aerodynamic and stiffness information. Regarding the manufacturing method that was developed, the process is the following: We create the lay-up that we have obtained from our study for any component that we want to manufacture, choosing from the beginning the type of overlap that we will follow. Then for curing, instead of an autoclave with high pressure and temperature, we use a simple oven or heated blankets, and we create negative pressure with a vacuum pump from the atmosphere. During the cure and while the matrix that has been used is in a liquid state, we apply vibrations, for example with a pneumatic vibrator, to the mold near its resonance point. We use a long curing cycle by choosing the lowest temperature that the matrix allows us to increase the time during which its viscosity is low. This drives the bubbles through the layers of the composite. If required, we also do a post cure to raise the Tg or to increase the resistance to environmental conditions. The result is a part with porosity, similar to what we would have if we had done the process in an autoclave. The final piece, however, is less brittle and has significantly better resistance to impacts, while also having an equivalent or better lifespan. In the bicycle frame in our case, the result, in relation to the frame made in an autoclave, was the significantly increased shock absorption and the non-failure in several cases where the frame from the autoclave failed e.g. from debris thrown by the tires and from crashes. In addition, the fact that there is no need for an autoclave significantly reduces the cost of investment and use of specialized equipment and thus of the final product. This approach can be exploited by many sectors, apart from the case of bicycle frames, in order to reduce the design and production costs of components made from Composite materials. Indicatively some of them are: The Sports Equipment Industry of all kinds, the Automotive Industry, Medicine, Shipping, the Aviation Industry, Construction, Biocomposites Applications and Repairs of Composite Materials. If this method is applied on a large scale, it can make composite materials more accessible, resulting in them being introduced into many areas of our life, improving it. I want to believe that the scientific community and the industry will further develop it for the benefit of everyone!
Degree
thesis:*- Grantor dc:publisher
- National Technical University of Athens (NTUA)
- Year dc:date
- 2023
Author and committee
dc:creator, dc:contributor.*- Authors dc:creator
-
- Kitselis, Alexandros
- Κιτσέλης, Αλέξανδρος
Subjects
dc:subject × 21- Σύνθετα υλικά
- Σκελετός ποδηλάτου
- Περερασμένα στοιχεία
- Υπολογιστική ρευστομηχανική
- Σχεδιασμός προϊόντος
- Αντοχή υλικών
- Πεπερασμένα σχοιχεία
- Κατασκευές από ανθρακονήματα
- Composite materials
- Bicycle frame
- Finite element analysis
- Computational fluid dynamics
- Product design
- Strength of materials
- Carbon fiber constructions
- Επιστήμη Μηχανολόγου Μηχανικού
- Επιστήμες Μηχανικού και Τεχνολογία
- Μηχανολογια οχημάτων
- Mechanical Engineering
- Engineering and Technology
- Automotive Engineering
Rights
- Language dc:language
- gre
Identifiers
dc:identifier.*- Identifier
- 10.12681/eadd/57312