Back to search

Institutes outside Greece

Measuring lubricant viscosity at a surface and in a bearing film using shear-horizontal surface acoustic waves

Abstract

dc:description

Viscosity is an important property of lubricant oil films; in IC engines the oil film is responsible for supporting the load, keeping the components in relative motion separated and protecting them from major friction and wear. As a result, lubricant film viscosity strongly depends on the operating temperature, pressure and shear rate. Understanding the oil behaviour under real operating conditions is of great interest, for developing better lubricants. Reproducing these conditions in a laboratory viscometer, to investigate the lubricant behaviour, is a challenging task. As a result, methods that allow measuring properties of lubricant films in-situ, are preferred. In this thesis, an ultrasonic method employing shear horizontal surface acoustic waves (SH-SAWs) was developed, to measure lubricant viscosity and surface layers, at a free surface and an in-situ bearing film. Ultrasonic methods have been widely used to measure liquid properties. Bulk acoustic waves and surface acoustic waves have been used to measure viscosity, film thickness and surface layers. Among the different types of ultrasonic waves, shear-horizontal surface acoustic waves are considered to be more suitable for measuring oil viscosity and formation of surface layers, in-situ in a running bearing application, as they present good coupling with liquids and moderate sensitivity to surface changes. The SH-SAW response was investigated at a solid-liquid interface, for measuring lubricant properties. SH-SAWs attenuate at the solid-liquid interface, due to the liquid viscosity, and the attenuation was modelled as function of the liquid properties, material and geometry of the medium, and wave frequency. The SH-SAW attenuation-viscosity model was used to calculate the viscosity of different oils at a free surface, over a range of temperatures, which agreed with numerical models. The SH-SAW response was further investigated for measuring the formation of viscous surface layers. Thin (h~ 10 to 30 nm) physically adsorbed surface layers were hard to detect. Further testing, has shown the successful application of SH-SAWs for detecting thick (h> 4.6 μm) surface layers, through a dry contact interface. Additionally, thick (h≥ 1.5μm) surface layers were detected through viscosity changes at a wet contact interface, using SH-SAWs. Finally, the SH-SAW method was utilised for measuring viscosity of oil films, in-situ in a journal bearing application. For the purpose of the study, a rotating journal and two bearing sleeves were set up in a rig, where different loading conditions were applied to create oil films of various thickness. The minimum film thickness due to loading and rig design, was expected to occur at the lower bearing sleeve, which was instrumented with two angled SH-SAW transducers to measure the changes in oil film viscosity with pressure. In addition to the angled SH-SAW transducers, an ultrasonic shear transducer was installed inside the rotating journal, which allowed measurements of the oil film viscosity circumferentially. The two methods were found to be in good agreement. Both, successfully distinguished the different oil test samples, according to their viscosities and were able to measure changes in the oil film viscosity at the loaded region, however they were unable to measure any surface layer formation. This thesis sets the foundation for the development of a method that potentially can bridge the gap between laboratory and in-situ testing; the SH-SAW method can be used for laboratory measurements of the oil viscosity, as well as in-situ an oil film viscosity measurements. As a result, the SH-SAW method could offer more consistent tracking of the oil properties throughout the development stages, the ability to keep tracking the properties of the fully formulated product when tested in an engine, and monitor the condition of the oil over time, for degradation. That would have significant impact on the automotive and lubricant industries, as it would significantly advance the understanding of the oil composition to help in the development of better lubricant products.

Degree

thesis:*
Grantor dc:publisher
Institutes outside Greece
Year dc:date
2020

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Tyreas, Georgios
  • Τυρέας, Γεώργιος

Subjects

dc:subject × 14

Rights

Language dc:language
eng

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/57522

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Tyreas, Georgios; Τυρέας, Γεώργιος. Measuring lubricant viscosity at a surface and in a bearing film using shear-horizontal surface acoustic waves. Institutes outside Greece, 2020. http://hdl.handle.net/10442/hedi/57522