Back to search

University of Patras

Μη καταστροφική μέτρηση καμπτικών συχνοτήτων ταλάντωσης για την ανίχνευση ρωγμών σε μεταλλικές, πλαστικές και τσιμεντένιες δοκούς με τη χρήση μαγνητοελαστικών αισθητήρων σε μορφή μικροσύρματος και κορδέλας

Abstract

dc:description

In this project, magnetoelastic sensors (in ribbon and microwire form) were used to detect cracks in concrete beams, as well as to measure the bending vibration frequencies of concrete and metal beams. The dissertation is divided into three parts. In the first part, an attempt was made to measure the bending vibration frequencies of an aluminum cantilever beam indirectly, using smaller plastic beams printed with a 3D printer. The metal beam was fixed using a press and connected to a mechanical oscillator, which was in turn connected to a frequency generator. The plastic beam was attached with tape to the free end of the metal beam. The sensor was attached both externally on the plastic beam and internally at various depths. A detection coil and a multimeter were added to the setup. Thus, when the oscillator operated, it excited (forced) the beam at specific frequencies, and when resonance occurred, the sensor generated an EMF, which was detected by the multimeter. In this way, all the natural frequencies of the metal beam were recorded. It should be noted that the measured frequencies differed from those of a simple metal beam due to the addition of the plastic beam. Finally, it should be mentioned that the same experiment was repeated with the sensor placed externally as well as at various depths inside the plastic beam, in order to determine whether depth affected detection. In the second part, an attempt was made to detect cracks in concrete beams with free ends using a ribbon-type sensor by identifying the natural vibration frequencies of the beam. The beams, with dimensions 4×4×16 cm³, were cast in special molds using commercial cement according to EN 76 196-1 standards in a specialized laboratory. The sensors were attached to the surface of the beams using special double-sided adhesive tape. For supporting the beams, both a metal and a wooden base were used for comparison, and signal detection was performed using a coil. The coil was connected to the microphone input of a computer, and the spectrum analysis software provided the vibration frequencies of the concrete beams through Fourier transformation. By measuring the frequencies of the beam with and without a crack, the crack could be detected from differences in the signal. In the third part, the behavior of the two sensors—ribbon and wire—was studied comparatively. Hysteresis loops were measured, as well as the sensors’ response to an applied external alternating magnetic field of 1–300 kHz. Then, again in comparison, the bending vibration frequencies and crack detection in concrete beams were examined using a setup similar to that of the second part. Finally, the frequencies of a concrete beam were detected with the sensors embedded inside the beam.

Degree

thesis:*
Grantor dc:publisher
University of Patras
Year dc:date
2025

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Tapeinos, Christos
  • Ταπεινός, Χρήστος

Subjects

dc:subject × 13

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/60356

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Tapeinos, Christos; Ταπεινός, Χρήστος. Μη καταστροφική μέτρηση καμπτικών συχνοτήτων ταλάντωσης για την ανίχνευση ρωγμών σε μεταλλικές, πλαστικές και τσιμεντένιες δοκούς με τη χρήση μαγνητοελαστικών αισθητήρων σε μορφή μικροσύρματος και κορδέλας. University of Patras, 2025. http://hdl.handle.net/10442/hedi/60356