Back to search

Technical University of Crete (TUC)

Καταλυτικές διεργασίες ξηρής αναμόρφωσης του CH4 και εμπλουτισμός του αερίου σύνθεσης σε H2 μέσω της αντίδρασης μετατόπισης του CO με υδρατμό

Abstract

dc:description

In the present doctoral thesis, the development and optimization of supported metal catalysts for the reactions of Dry Methane Reforming (DRM) and Water–Gas Shift (WGS) are investigated. To this end, the research focused on the systematic study of critical parameters that influence the performance of catalysts for these two processes. For the DRM reaction, the effect of the nature of the metal (Ru, Rh, Ir, Pt, Ni, Re), the support (Al₂O₃, TiO₂, ZrO₂, YSZ, La₂O₃), the use of mixed oxides as supports (x%MₓOᵧ-Al₂O₃, M: Ti, Y, Zr, La, Sm, Ce, Nd, Gd), the modification of catalysts through the addition of a second metal (Ni-Rh), as well as various operating parameters (GHSV, CH₄/CO₂ ratio, time-on-stream) on catalytic performance was examined. For the WGS reaction, the effect of the support’s nature (Al₂O₃, ZrO₂, CeO₂, GDC) and morphology (nanorods, irregular nanoparticles) on Pt-supported catalysts, as well as the influence of the addition of suitable promoters (Na, K, Li, Cs), on the catalytic performance was investigated. The synthesized catalysts were characterized using several techniques, such as nitrogen physisorption (BET method), X-ray diffraction (XRD), selective chemisorption with Η2, temperature-programmed reduction with hydrogen (H₂-TPR), temperature-programmed oxidation (TPO), temperature-programmed desorption of CO₂ (CO₂-TPD) and transmission and scanning electron microscopy (TEM, SEM), aiming to correlate their physicochemical properties with their catalytic activity. In parallel, mechanistic studies of the DRM and WGS reactions were carried out mainly by in-situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and, to a lesser extent, by mass spectrometry (MS). These studies enabled the identification of (a) the nature and population of reaction intermediates formed under reaction conditions and their correlation with the gas-phase products, and (b) the elementary steps that constitute the mechanism of each reaction. The results showed that the catalytic performance for the DRM reaction is significantly affected by the nature of both the metallic phase and the support. Rhodium and ruthenium catalysts supported on YSZ or ZrO₂ exhibited optimal behavior, which, in addition to high CH₄ and CO₂ conversions, led to H₂/CO ratios approaching unity at temperatures above 700 °C. Stability tests conducted over 0.5%Rh/ZrO₂, 0.5%Ru/ZrO₂, 1%Rh/Al₂O₃, and 1%Ru/Al₂O₃ catalysts under DRM conditions showed that the performance of catalysts over reaction time depends on the metal–support combination employed. It was found that the Rh catalyst exhibited excellent stability for 30 hours on stream, in contrast to the Ru/ZrO₂ catalyst, which was slightly deactivated. On the other hand, the 1%Rh/Al₂O₃ catalyst presented slight deactivation after 30 hours of operation, while the 1%Ru/Al₂O₃ catalyst exhibited progressive and significant deactivation after 40 hours on stream, which was found to be mainly due to thermal sintering and, to a lesser extent, carbon deposition. The sintering of Ru particles when dispersed on Al₂O₃ support appears to be enhanced by the presence of RuOₓ species, which cannot be reduced to Ru⁰ under DRM conditions, as it was found to occur when Ru is dispersed on ZrO₂ support. The effect of operating parameters on the catalytic performance for the DRM reaction was examined on 1%Rh/Al₂O₃ and 1%Ru/Al₂O₃ catalysts and it was found that increasing the CH₄/CO₂ ratio leads to lower CH₄ conversion, higher CO₂ conversion, and an increase in the produced H₂/CO ratio. The decrease in GHSV resulted to higher reactant conversions for both catalysts, while its effect on the H₂/CO ratio was limited. The results of in-situ DRIFTS experiments conducted over 1%M/Al₂O₃ (M: Rh, Ru, Ni, Re), 0.5%Rh/ZrO₂, and 0.5%Ru/ZrO₂ catalysts showed that the DRM reaction proceeds via a bifunctional mechanism according to which CH₄ adsorbs dissociatively on metal sites, leading to the formation of adsorbed hydrogen atoms and CHₓ intermediates. Part of the hydrogen atoms diffuses to the surface of the support, where it interacts with adsorbed CO₂ producing formate species, while the remaining hydrogen atoms recombine to produce H₂ in the gas phase. The CHₓ species interact with the hydroxyl groups of the support, also producing formate species, which eventually decompose into CO adsorbed on the metal surface. In addition to the production of formate species, CO₂, which is activated mainly on the support surface, is also responsible for the formation of carbonate species, which subsequently decompose, contributing to the population of adsorbed CO species that eventually desorb in the gas phase. Part of the produced CO may also originate from the decomposition of CO₂ at temperatures above 450 °C. The addition of metal oxides TiO₂, Y₂O₃, ZrO₂, La₂O₃, CeO₂, Nd₂O₃, and Gd₂O₃ to the Al₂O₃ support led to a significant increase in the turnover frequencies of CH₄ (TOFCH₄) and CO₂ (TOFCO₂) conversions of Rh-supported catalysts (0.5 wt.%) for the DRM reaction, in a manner that depends on the nature and loading of the added metal oxide. The 0.5%Rh/10%La₂O₃-Al₂O₃ and 0.5%Rh/10%TiO₂-Al₂O₃ catalysts exhibited optimal performance, leading to TOFCH₄ and TOFCO₂ values approximately 3 and 4 times higher, respectively, compared to those measured for the 0.5%Rh/Al₂O₃ catalyst. This improvement in catalytic activity is attributed to the enhanced reducibility of the RhOx species caused by the addition of MₓOᵧ, which appears to facilitate the activation of CH₄ on the Rh surface through modification of the electronic properties of Rh metal nanoparticles. In parallel, the reducibility of the MₓOᵧ particles that are in close contact with Rh crystallites also appears to affect catalytic activity, which is optimized for catalysts that exhibit intermediate reducibility of these species. In-situ DRIFTS experiments conducted over 0.5%Rh/X%La₂O₃–Al₂O₃ (X = 0–20 wt.%) catalysts showed that the relative population of formate species on the surface of the catalysts containing La₂O₃, which are considered active intermediates for the DRM reaction, is higher compared to that of the 0.5%Rh/Al₂O₃ catalyst. This was attributed to the higher reducibility achieved by the presence of La₂O₃ on the Al₂O₃ surface, which likely enhances both the adsorption/activation of CH₄ on the Rh surface, which is the primary step for the formation of formate species, and the subsequent elementary steps involved in the mechanism of their formation. The investigation of the DRM reaction over supported Ni catalysts (5 wt.%) showed that the addition of La₂O₃ to Al₂O₃ and ZrO₂ supports leads to a significant improvement in catalytic performance. For Ni/X%La₂O₃–Al₂O₃ catalysts (X: 0–100 wt.%), the activity is strongly influenced by the La₂O₃ content and is optimized for the catalyst containing 20 wt.% La₂O₃, which exhibits moderate surface basicity. The partial substitution of Ni with a small amount (0.1 wt.%) of Rh in the optimal Ni/20%La₂O₃-Al₂O₃ catalyst resulted in a further increase of CH₄ and CO₂ conversions, a higher H₂/CO ratio, improved stability, and a reduction in carbon deposition on the catalyst surface. The mechanistic study conducted using a combination of infrared spectroscopy and mass spectrometry showed that the presence of Rh does not alter the mechanistic pathway of the DRM reaction but merely enhances the reactivity of the reactants and intermediate species, ultimately leading to increased catalytic activity, likely due to improved dispersion of the metallic phase and optimization of the surface basicity of the support. Results obtained from the investigation of the WGS reaction showed that the performance of supported Pt catalysts (0.5 wt.%) depends on both the nature and the morphological characteristics of the support. Higher activity was observed for Pt catalysts supported on CeO₂ and, especially, on Gd₂O₃-CeO₂ (GDC) with nanorod morphology (NRs), compared to those with irregularly faceted nanoparticle morphology (IRFP). The Pt/GDC(NRs) catalyst exhibited remarkably high activity, comparable to that of state-of-the-art low-loading Pt catalysts reported in the international literature, as well as satisfactory stability and resistance to thermal aging under oxidizing conditions. In-situ DRIFTS studies performed under reaction conditions showed that the active sites for the activation and conversion of CO towards CO₂ and H₂ are Pt crystallites that are in contact with Ce³⁺ ions. The formation of these active sites is promoted by the enhanced reducibility of the GDC and CeO₂ supports with nanorod structure, which facilitates the reduction of CeO₂ by adsorbed CO under WGS reaction conditions, either directly through CO oxidation (redox mechanism) or indirectly by participating in the formation of reactive hydroxyl groups (associative mechanism). The addition of small amounts of alkali metals (Na, Li, K, Cs) on Pt catalysts (0.5 wt.%) supported on Al₂O₃ and ZrO₂ does not affect their catalytic performance for the WGS reaction. In contrast, the addition of alkali metals on CeO₂ support leads in all cases to an increase in CO conversion, with the Pt/0.06%Na-CeO₂ and Pt/0.34%Cs-CeO₂ catalysts showing the best performance and excellent stability for 30 hours on stream. For the Na-promoted catalyst, it was found that CO conversion is optimized at an intermediate Na content, corresponding to a Na:Pt ratio of 1:1. H₂-TPR and in-situ DRIFTS experiments showed that the addition of alkali metals on Pt/CeO₂ catalysts promotes the partial reduction of Ce⁴⁺ to Ce³⁺, leading to the formation of Pt–Ce³⁺ active sites at the metal–support interface, confirming that these sites constitute the catalytically active sites for the WGS reaction. The results of the present PhD thesis demonstrate that the performance of the DRM and WGS reactions, two processes of exceptional importance for hydrogen production and fuel cells technologies, can be significantly improved through the appropriate selection of metal–support combination and operating reaction conditions, contributing to the integration of H₂-derived energy into electricity generation methods and to the global energy transition strategy.

Degree

thesis:*
Grantor dc:publisher
Technical University of Crete (TUC)
Year dc:date
2025

Author and committee

dc:creator, dc:contributor.*
Authors dc:creator
  • Androulakis, Athanasios
  • Ανδρουλάκης, Αθανάσιος

Subjects

dc:subject × 11

Rights

Language dc:language
gre

Identifiers

dc:identifier.*
Identifier
10.12681/eadd/60533

Chain of custody

source
Harvested from
Greek National Archive of PhD Theses
Base URL
phdtheses.ekt.gr/eadd_oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
citation

Androulakis, Athanasios; Ανδρουλάκης, Αθανάσιος. Καταλυτικές διεργασίες ξηρής αναμόρφωσης του CH4 και εμπλουτισμός του αερίου σύνθεσης σε H2 μέσω της αντίδρασης μετατόπισης του CO με υδρατμό. Technical University of Crete (TUC), 2025. http://hdl.handle.net/10442/hedi/60533