Zepler Institute for Photonics and Nanoelectronics
Development of Short-wave Infrared Fibre Lasers
Abstract
dc:description.abstract<p class="MsoNormal">Although Thulium and erbium doped fibre lasers are common, and used in a wide array of applications, there are methods of operation which are not well matured. In this work, the operation of laser sources utilising both dopants in power scalable architectures is investigated to explore their potential. </p> <p class="MsoNormal">To mitigate the impact on device efficiency caused by long device lengths in Er-doped fibre lasers (EDFLs), brightness enhancement of few-moded fibres through bend loss is investigated in chapter 3. By careful design of the fibre to compromise between core to cladding area ratio and modal content, it is found that inducing bend loss is an effective way to achieve diffraction limited beam quality in large mode area (LMA) fibres. </p> <p class="MsoNormal">In chapter 4 it is discussed how EDFLs compare against competing sources in the 1500 - 1600 nm wavelength band. In particular, how power-scaling differs between Yb sensitised Er-doped sources, and Er-only devices. The impact of pair-induced-quenching (PIQ) and long device lengths is modelled to arrive at optimal device parameters, which are then utilised in a real device. In a cladding pumped configuration, 104 W of singlemode output power is demonstrated with slope efficiencies of 24% (30%) with respect to launched (absorbed) pump power. Furthermore, the linearity of the observed slope efficiency and good thermal properties of the device lend themselves to further power scaling by increasing the available pump power and further optimisation of the fibre design.</p> <p class="MsoNormal">In chapter 5, the difficulty in operating Tm-doped fibre lasers (TDFLs) around 1700 nm is discussed, and the relevant fibre design parameters modelled. Through the use of in-band core-pumping with the EDFL presented in chapter 4, and an ultra-low dopant concentration Tm-doped fibre (TDF), a TDFL which displays 47 W of output power at 1726 nm is presented. The tuning capabilities of this pump and fibre combination are also explored; A maximum tuning range of 371 nm (1654-2025 nm), and 360 nm above 1 W, is presented, an improvement of 44% over that previously reported for similar fibre compositions. </p> <p class="MsoNormal">The commercial options for pumping Er:YAG in the 1532 nm band are explored in chapter 6. Accessing the narrow absorption line at 1532 nm requires a pump source such as an Er/Yb fibre laser. By comparing the relative performance of two commercial fibres, it is shown that their composition; primarily the ratio of erbium to ytterbium, has a significant impact on their performance limits. With the higher ratio of erbium to ytterbium displaying much higher spectral purity. In a simple linear configuration a maximum output power of 15 W is achieved with an efficiency of 42% with a spectral purity of 99.3%. </p> <p class="MsoNormal">Aluminium beam dumps are frequently used to terminate high power beams where needed. It is often taken for granted that these dumps are not perfect absorbers, particularly as a black anodised coating may lead one to intuitively think otherwise. In v chapter 7, a simple and reliable method for determining the total reflectivity of a material is developed and used to characterise a variety of aluminium coatings. Several coatings are tested, all of which appear black and are thus assumed to absorb in the visible region. Reflectivity is determined by measuring the amount of energy deposited into a known mass of aluminium through calorimetry and calculating the transmission of a known beam power. A number of coatings tested displayed reflectivity below 20% at 975 nm, 1580 nm, and 2090 nm. However, it is found that a number of these coatings display a very low damage threshold. In particular, powder coated samples which are polymer-based. Only one of the coatings tested in this work is shown to withstand suitable beam powers, with an approximate damage threshold at 975 nm of 1470 W cm−2 . Though thoughtful beam dump design may not preclude coatings with a lower damage threshold.</p>
Degree
thesis:*- Name dc:type.qualificationname
- Ph.D.
- Level dc:type.qualificationlevel
- doctoral
- Grantor dc:publisher.institution
- Zepler Institute for Photonics and Nanoelectronics
- Year dc:date.issued
- 2021
Author and committee
dc:creator, dc:contributor.*- Author dc:creator
-
- Burns, Mark, David
- Advisors dc:contributor.advisor
-
- Shardlow, Peter
- Clarkson, W.A.
- ORCID person:identifier.orcid
Rights
- Language dc:language
- English, eng