University of North Texas
Lubrication Mechanisms of Molybdenum Disulfide Spray Coatings in Low-Viscosity Hydrocarbon Environments
Abstract
dc:descriptionThis research aims to understand scientific mechanisms of lubrication with molybdenum disulfide (MoS2) solid lubricant coatings in low-viscosity hydrocarbons. A simple and economical spray-deposition of MoS2 is used to coat steel and WC surfaces for testing in simple low-viscosity hydrocarbon liquids across a variety of sliding conditions. Polar (ethanol), and non-polar (dodecane) hydrocarbons were used to study the effects of polarity and affinity for water on MoS2 lubrication mechanisms and tribological behavior. Hexane, decane, and hexadecane were also used to understand the effect of fluid viscosity and hydrocarbon chain length. MoS2/WC/steel duplex coatings were compared to MoS2/steel to investigate the effect of a harder, load supporting base layer on the friction and wear properties of the MoS2 coating. This work highlights the importance of hydrocarbon chemistry on the friction behavior of MoS2, where MoS2 on both WC and steel substrates tested in polar ethanol consistently showed sharp increases in friction coefficient after just a few sliding cycles. This friction increase was attributed to oxidation caused by both adsorption of ethanol molecules to polar components on the MoS2 surfaces, such as edge sites and vacancy sites along the basal plane, causing the MoS2 to readily oxidize and form molybdenum trioxide (MoO3). In contrast, non-polar hydrophobic alkanes, such as dodecane, do not show such deterioration of MoS2 coating, and the friction coefficient remains low throughout the duration of the test, indicating a synergistic effect of the MoS2/alkane solid/liquid lubricating system. Higher chain-length alkanes like hexadecane were found to produce lower friction when lubricating MoS2 than lower-chain length alkanes. Hydrocarbon viscosity was also found to be a factor in determining the friction behavior of MoS2, and friction decreased as viscosity decreased for testing at elevated temperatures. Largest differences in the water contact angle (WCA) were found on MoS2 surfaces exposed to liquid hydrocarbons, where hydrocarbon contamination rendered the MoS2 surface hydrophobic. MoS2/WC duplex coating architecture was found to provide substantially lower wear rates than MoS2/steel when lubricated with both ethanol and dodecane. The effect of contact pressure on the lubrication mechanisms of MoS2/WC coatings was investigated using Raman spectroscopy and MicroXRD, finding that microstructural changes occur inside the wear track, such as decrease in crystallinity and basal plane alignment. The identified mechanisms that occur between low-viscosity hydrocarbons and MoS2 can be used for solid/liquid lubrication systems in fuel-lubricated tribological systems. The results of this work provide a foundation for understanding the tribological properties of MoS2 in polar and non-polar short chain hydrocarbons that previously has not been established, and the obtained knowledge opens new possibilities for wear protection of fuel pump systems designed to operate with low viscosity hydrocarbons.
Degree
thesis:*- Grantor dc:publisher
- University of North Texas
- Year dc:date
- 2024
Author and committee
dc:creator, dc:contributor.*- Author dc:creator
-
- Cairns, Euan James
- Contributors dc:contributor
-
- Voevodin, Andrey
- Berman, Diana
- Aouadi, Samir
- Berkebile, Stephen
- Scharf, Thomas
Subjects
dc:subject × 4Rights
dc:rights- Statement dc:rights
-
- Public
- Cairns, Euan James
- Copyright
- Copyright is held by the author, unless otherwise noted. All rights Reserved.
- Language dc:language
- English
Identifiers
dc:identifier.*- Identifier
-
local-cont-no: submission_4029
https://digital.library.unt.edu/ark:/67531/metadc2415931/
ark: ark:/67531/metadc2415931