Back to search

Institutional Repository of Vilnius University

Nerūdijančio plieno bandinių giluminis graviravimas naudojant femtosekundinio lazerio papliūpų režimą /

Abstract

dc:description

Deep Engraving of Stainless Steel Using a Femtosecond Burst-Mode Laser The aim of this paper was to investigate the properties of formed microgrooves using different machining parameters. This research is crucial due to the fact that the properties of metals micromachining have not been fully investigated yet so it is unclear how the result of micromachining depends on individual parameters. High surface roughness (Rz = 70 &#956;m) microgrooves formed on metal surfaces are used in harnessing the Solar energy which enhance generated power output of thermoelectric generators. Also, formed surfaces are used in stealth technology. During the experiment the depths and surface roughness were under investigation of the formed microgrooves on stainless steel. These microgrooves were formed using N and P bursts of femtosecond laser with different machining parameters such as laser repetition rate, scanning overlapping, the number of laser pulses in bursts. After the experiment it was determined that the effectiveness of machining of stainless steel using N bursts (3,3 &#956;m3/&#956;J) is higher as compared with effectiveness of machining using P bursts (1,4 &#956;m3/&#956;J), but these values are lower as compared with the usual laser regime (3,8 &#956;m3/&#956;J). Fabrication using burst of pulses (4;1) and (8;1), when the scanning overlapping is equal to 77,3 %, produces microgrooves with smoother surfaces as compared with microgrooves produced using the usual laser regime, but when the scanning overlapping decreases to 55,4 %, surface roughness of a formed microstructure increases. Forming microgrooves using P bursts of pulses, when the laser repetition rate is at range of 100 kHz – 600 kHz, 5 – 8 times smoother surface is acquired, in a comparison with the usual laser regime. When the laser repetition rate increases from 100 kHz to 600 kHz, the value of surface roughness parameter Ra of a microgroove increases from 0,5 &#956;m to 1 &#956;m, but when the laser repetition rate reaches 1 MHz, rough surfaces are formed. Scanning overlapping does not have an influence on the surface roughness parameter Ra value of the microgrooves when bursts of P pulses are being used for machining. The majority of rough (Ra > 2 &#956;m) formed surfaces are dark and they do not have a fine surface structure. The majority of smooth (Ra < 1,5 &#956;m) formed surfaces are bright and the have a regular surface structure. In other part of this research it was estimated that the highest efficiency of formation of microgrooves is achieved, whenever optimal ablation fluence is being used which value is &#8776; 4 J/cm2. It is possible to change the value of the fluence by changing laser repetition rate, the amount of pulses in a burst or average power and when these parameters are set in a way that laser fluence value is &#8776; 4 J/cm2, then the highest efficiency of formation of microgrooves is achieved (1 energy unit releases the highest volume of material) and the value of this efficiency is &#8776; 3,8 &#956;m3/&#956;J. It was also estimated that the increase of the scanning speed from 1 m/s to 3 m/s does not influence the efficiency of micromachining. Another important estimation is that the removed material volume during a constant period of time is the highest when the micromachining parameters are set in a way that the value of fluence is equal to the optimal fluence value. When the average laser power is equal to 30 W, then the highest removed material volume during a constant period of time is equal to 5,5 mm3/min.

Degree

thesis:*
Grantor dc:publisher
Institutional Repository of Vilnius University
Year dc:date
2020

Author and committee

dc:creator, dc:contributor.*
Author dc:creator
  • Svirskas, Žilvinas,
Contributors dc:contributor
  • Butkus, Simas

Rights

dc:rights
Statement dc:rights
  • info:eu-repo/semantics/openAccess
Language dc:language
lit

Identifiers

dc:identifier.*

Chain of custody

source
Harvested from
Vilnius University
Base URL
epublications.vu.lt/oai
Last updated
2026-11-19
Source record
OAI-PMH GetRecord
related terms
citation

Svirskas, Žilvinas,. Nerūdijančio plieno bandinių giluminis graviravimas naudojant femtosekundinio lazerio papliūpų režimą /. Institutional Repository of Vilnius University, 2020. https://repository.vu.lt/VU:ELABAETD107237441&prefLang=en_US