Institutional Repository of Vilnius University
Lazerio pritaikymas stibio selenido dangos apdirbimui /
Abstract
dc:descriptionLasers are becoming a popular tool for working with materials because they're versatile and precise. We can fine-tune settings like laser wavelength and intensity to achieve different effects. This allows us to vaporize material (ablation), melt or smooth surfaces, alter impurities, or even trigger crystal formation within the material. By adjusting the laser settings, we can heat specific layers or modify surfaces in the cell. Laser heating is much faster than conventional heating methods that rely on ovens, which can speed up production and improve how solar cells are made. This research focused on antimony selenide thin films due to their advantageous properties for application in thin-film solar cells. Antimony selenide exhibits a favorable environmental profile being a non-toxic material. Additionally, its band gap falls within the optimal range (1.0-1.2 eV) for efficient light absorption in solar cells. Furthermore, the material boasts a high absorption coefficient, particularly within the visible light spectrum (greater than10^5 cm^(-1)). Finally, antimony selenide demonstrates good carrier mobility (~10 cm2V-1s-1), facilitating the transport of generated charge carriers within the device. Due to these characteristics antimony selenide is a promising candidate for the development of solar cell technologies. In this study we explore how laser irradiation can be used to alter the properties of antimony selenide thin films. To achieve it, two distinct deposition techniques were employed to fabricate Sb_2 Se_3 thin films. Thermal evaporation yielded amorphous Sb_2 Se_3 coatings, characterized by a lack of long-range order, while vapor transport deposition resulted in crystalline coatings with a well-defined atomic arrangement. We then tried using a pulsed laser with a wavelength of 1064 nm to heat the amorphous film. A hermetic box was developed and used to isolate the laser-irradiated samples from atmospheric influences. However, this wavelength seemed to pass right through the material with minimal absorption. To confirm this, we used ellipsometry measurement to figure how deeply different light wavelengths are absorbed by both amorphous and crystalline Sb_2 Se_3 films. Based on these findings, we chose a continuous wave (CW) laser with a wavelength of 830 nm for further study. We then monitored the changes in the film's structure during laser irradiation during in-situ Raman spectroscopy measurement. The results from this technique clearly showed that the amorphous film transformed into a crystalline phase when exposed to the 830 nm laser radiation. This experiment successfully confirms that lasers can be used to crystallize amorphous Sb_2 Se_3 thin films. Then, a 532 nm pulsed laser with two galvanometric mirrors was used for surface scanning. By optimizing parameters like laser power density and scanning frequency, we established a method for creating uniform thin films. This method yielded amorphous layers with a depth of approximately 24 nm. To explore the capabilities of shorter wavelengths, we employed a 355 nm pulsed laser, achieving a minimum amorphous layer depth of 10 nm. Subsequently, samples irradiated with both 355 nm and 532 nm lasers were analyzed using Raman spectroscopy at various wavelengths. This investigation provided valuable insights into the depth profile of laser-induced modifications. Laser irradiation experiments using various wavelengths demonstrated the ability to generate well-defined amorphous surface layers on Sb_2 Se_3 thin films. Notably, irradiation at 830 nm induced crystallization within the amorphous material. These targeted structural modifications are important for light-absorbing materials due to their impact on charge transport phenomena. Consequently, the study highlights the potential of laser irradiation, particularly at 830 nm, as a technique for tailoring the surface properties of Sb_2 Se_3 thin films, potentially leading to optimized solar cell performance.
Degree
thesis:*- Grantor dc:publisher
- Institutional Repository of Vilnius University
- Year dc:date
- 2024
Author and committee
dc:creator, dc:contributor.*- Author dc:creator
-
- Mickevičius, Gustas,
Rights
dc:rights- Statement dc:rights
-
- info:eu-repo/semantics/openAccess
- Language dc:language
- lit
Identifiers
dc:identifier.*- Repository record dc:identifier
- https://repository.vu.lt/VU:ELABAETD210578735&prefLang=en_US