Back to search

Virginia Polytechnic Institute and State University

Mechanical behavior and dislocation substructure of a 26 chromium - 6 nickel stainless steel

Abstract

dc:description.abstract

A 26Cr-6Ni stainless steel may have either a single phase or microduplex microstructure. The microstructure is dependent on heat treatment. Heat treating at 2300°F for 1.5 minutes and water quenching yields a 100 percent ferrite microstructure. Precipitation annealing at 1700°F for various times results in the precipitation of various amounts of austenite with the equilibrium microstructure being 60 percent ferrite-40 percent austenite. The mechanical behavior, tensile properties, as well as the dislocation arrangement and dislocation density as observed in the electron microscope of an alloy system containing two co-deforming phases are of interest in order to better understand the deformation characteristics of metals. The 100 percent ferrite is saturated with carbon which is manifested by the presence of a yield point as well as relatively high strength. The precipitation of austenite results in the elimination of the yield point as well as a decrease in the yield strength. The yield and ultimate strength of the microduplex material follow a mixture law of the form: σ<sub>md</sub> = σ <sub></sub> V<sub></sub>+ σ<sub>Y</sub> V<sub>Y</sub> where σ<sub>md</sub>, σ <sub></sub> and σ<sub>Y</sub> are the flow stresses of the microduplex material, ferrite and austenite respectively, and Vis the volume fraction of each phase. This equation indicates that deformation produces approximately uniform strain in the two phases in the microduplex structure. The dislocations formed at low strains in 100 percent ferrite were jaggy and uniformly distributed. With increasing stress dense tangles were formed, but there was no clearly developed cell structure. The flow stress, a, was found to depend upon the dislocation density, N, in accordance with the relation: σ = 3405 + 0.14 Gb N kg/cm<sup>2</sup> . The dislocation structures of the ferrite phase of the microduplex structure showed similar behavior to 100 percent ferrite with dislocation tangling being initiated at the ferrite-austenite interfaces. The microduplex austenite exhibited some stacking faults with dense dislocation tangles forming during deformation. The microduplex austenite transformed to martensite at strains above 0.12. These results show that at initial yielding the microduplex austenite is the "softer" phase in a harder ferrite matrix. During deformation, however, the uniform strains induced, combined with the higher work-hardening rate of the austenite phase, result in the austenite being the "harder" phase by the time the ultimate is reached.

Degree

thesis:*
Name thesis:degree_name
Ph. D
Level thesis:degree_level
doctoral
Discipline thesis:degree_discipline
Materials Engineering Science
Department dc:contributor.department
Materials Engineering Science
Grantor dc:publisher
Virginia Polytechnic Institute and State University
Year dc:date.issued
1970

Author and committee

dc:creator, dc:contributor.*
Author dc:creator
  • Greene, Alexander Beck
Chair dc:contributor.committeechair
  • Lytton, Jack L.
Committee members dc:contributor.committeemember
  • Floridis, T. P.
  • Houska, C. R.
  • Fricke, A. L.
  • Slack, L. H.

Rights

dc:rights
Statement dc:rights
  • In Copyright
Language dc:language.iso
en

Identifiers

dc:identifier.*
Handle dc:identifier.uri
https://hdl.handle.net/10919/138622

Chain of custody

source
Harvested from
Virginia Tech
Base URL
vtechworks.lib.vt.edu/oai/request
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
related terms
citation

Greene, Alexander Beck. Mechanical behavior and dislocation substructure of a 26 chromium - 6 nickel stainless steel. doctoral thesis, Virginia Polytechnic Institute and State University, 1970. https://hdl.handle.net/10919/138622