Back to search

University of Sheffield

Developing Smoothed Particle Methods for Modelling Continuum Mechanical and Thermal Behaviour in Nuclear Fuel and Cladding

Abstract

dc:description.abstract

The purpose of this work is to explore the validity of using smoothed particle methods for future applications within nuclear fuel modelling. The particle nature of the method makes it attractive for modelling the complex multi-physics environment of nuclear fuel. This work however focuses on the fundamental accuracy of the method within the bounds of current simple fuel performance models. The thesis is separated into four main sections: examination of simple heat flow models, the effect of particle arrangement, complex heat flow within thermal models of nuclear fuel and finally simple mechanical models. The examination of heat flow by smoothed particle methods begins with simple 1D models. Three approaches to modelling heat flow identified in the literature are tested and the results compared using errors calculated from the complimentary analytical models. One method is selected for further use within this work due to achieving the lowest error in results. Particular attention is given to the effect of boundary conditions on the models. Two main methods for handling boundaries are explored: the use of fixed boundary particle values against the use of dynamically assigned values. Dynamic boundaries are shown to offer reduced error compared to the fixed case. The effect of these boundaries are further explored for 2D models under both transient and steady state conditions. Dynamic boundaries are shown to suffer for discontinuous boundaries and more complex boundary shapes. A method is proposed for handling these issues and is shown to offer reduced error in the analytical model compared with the fixed boundary case. The effect of particle arrangement is explored for the more complex circular geometry which is applicable to models of nuclear fuel used within licensing codes. Three main particle arrangements are tested: square lattice, triangular lattice and concentric particle rings. The effect of relaxing these particle structures under density-dependent forces is also explored. Each of these particle arrangements are tested using the smoothed particle equation for heat flow identified in the earlier section. The model used is steady state heat flow in a 2D annulus and is considered due to the existence of a well-defined analytical model. This model is considered as a good simplified model for internally heated cladding around nuclear fuel. The triangular lattice is identified as the superior choice for particle arrangement for further use within this work due to the low errors demonstrated coupled with the fast construction and applicability to other geometries. These findings are then applied to a simple 2D model of nuclear fuel, equivalent to those found within current codes used for fuel licensing. This model is built up using simple 1D models for the purposes of validation. Each model presented has a well-defined analytical solution and introduces a new aspect of complexity in isolation of the others for the purposes of validation. A method for including heat generation is proposed by modification of methods given in the literature. This method is shown to be successful with boundary conditions being the largest contributing factor to the error. A modification to the heat equation to handle thermal interfaces is tested. The results although successful show room for further improvement by consideration of the boundary position between particle pairs. Multiple equations to handle a convective boundary condition within smoothed particle methods are proposed. One of these methods is shown to give acceptable results however future improvements are discussed. These complexities are then combined into the 2D fuel model and the results are shown to converge. This chapter findings support the notion that smoothed particle methods are capable of reproducing models currently in use within fuel licensing codes and is therefore worthy of further exploration by the National Nuclear Laboratory (NNL). Finally the work is extended to examine mechanical behaviours within simple nuclear fuel models. The equations for handling thermally induced strains within smoothed particle methods are introduced. The validity of these equations are first tested within 1D simple simulations using various corrective factors: velocity smoothing, density evolution and artificial viscosity. Velocity smoothing is found to make little impact on the simulation results, however the other two methods are shown to be required, particularly under the use of dynamic boundaries. These findings are then applied to a simplified cladding model with thermally induced strains in 2D. The model results are shown to converge with the analytical results. The future scope of the implementation of mechanical behaviour is outlined and a path toward future implementation of smoothed particle methods within nuclear fuel licensing codes is discussed.

Degree

thesis:*
Name dc:type.qualificationname
Ph.D
Level dc:type.qualificationlevel
doctoral
Grantor dc:publisher.institution
University of Sheffield
Year dc:date.issued
2022

Author and committee

dc:creator, dc:contributor.*
Author dc:creator
  • Horton, Matthew
Advisors dc:contributor.advisor
  • Travis, Karl
  • Mark, Bankhead
  • Amy, Gandy

Rights

Language dc:language.dcterms_iso639_2
eng

Identifiers

dc:identifier.*
Identifier
uk.bl.ethos.875005

Chain of custody

source
Harvested from
White Rose University Consortium
Base URL
etheses.whiterose.ac.uk/cgi/oai2
Last updated
2026-11-18
Source record
OAI-PMH GetRecord
related terms
citation

Horton, Matthew. Developing Smoothed Particle Methods for Modelling Continuum Mechanical and Thermal Behaviour in Nuclear Fuel and Cladding. doctoral thesis, University of Sheffield, 2022.