Spelling suggestions: "subject:" atrength"" "subject:" 1strength""
401 |
A study of the dynamic shear modulus of soil.Cheung, Che Hung January 1972 (has links)
No description available.
|
402 |
Shear strength of high performance concrete beams.Kong, Paul Y.L. January 1996 (has links)
An analytical and experimental investigation on the shear strength of High Performance Concrete (HPC) beams with vertical shear reinforcement or stirrups was carried out. The analytical work involved developing a theory based on the truss analogy, capable of predicting the response and shear strength of such beams subjected to combined bending moment and shear force.The experimental work comprised forty-eight beam specimens in eight series of tests. Most of the beams were 250 mm wide, 350 mm deep and had a clear span of approximately 2 metres. The largest beam was 250 mm wide, 600 mm deep and had a clear span of 3.1 metres. Test parameters included the concrete cover to the shear reinforcement cage, shear reinforcement ratio, longitudinal tensile steel ratio, overall beam depth, shear span-to-depth ratio and concrete compressive strength. The loading configurations included using one, two or four symmetrically placed concentrated loads on simply supported spans.The theory predicted the shear strength of the beams in the present study well. When beams from previous investigations were included, the theory also gave good prediction of the shear strength. Apart from this, comparisons of shear strength were also made with the predictions by the shear design provisions contained in the Australian Standard AS 3600 (1994), American Concrete Institute Building Code ACI 318-95, Eurocode EC2 Part 1 and Canadian Standard CSA A23.3-94. The AS 3600 method was found to give the best correlation with the test results among all the code methods.
|
403 |
Rheology Of Peroxide Modified Recycled High Density PolyethyleneParmar, Harisinh, h_arzoo@yahoo.com January 2008 (has links)
Consumption of plastics has increased exponentially, in line with the world's population. Not surprisingly this is reflected in enormous growth of the plastic industry especially during the last five decades. Commensurate with this, waste produced from plastics consumption has created a major environmental problem. Many types of waste disposal methods have been used all over the world so far, but all of them have disadvantages. Furthermore, some methods are responsible for the generation of green house gases and further contribution to global warming. Recently, reduction of green house gas emission has become a target of most industries. Plastic recycling and reuse breaks the cycle of endless production of virgin polymer and thus contributes to a net reduction of green house gas emission. Recycling of plastics should produce materials with improved properties to replace virgin plastics for a variety of applications. Improvement in the properties of recycled plastics can be achieved by blending with other plastics, by filler addition and by modification using free radical initiators. Introduction of the free radical initiator (organic peroxide) during reprocessing of the recycled plastics has been found to offer significant property improvements to the recycled materials. Extremely small amounts of a free radical initiator (typically ranging between 0.01 wt% to 0.2 wt%) is capable of enhancing the properties of the recycled plastics to a great extent. This project investigates the use of free radical initiators in the recycling of post consumer recycled high density polyethylene using reactive extrusion. Both molecular and rheological characterisation of recycled and reprocessed materials was carried out and this was followed by tensile testing of the modified materials to satisfy end use applications such as packaging and drainage piping. Post consumer recycled high density polyethylene (R-HDPE) resin and virgin high density polyethylene (V-HDPE) were reactively extruded with low concentrations of dicumyl peroxide (DCP) and 1, 3 1, 4 Bis (tert- butylperoxyisopropyl) Benzene (OP2) respectively in a twin screw extruder in order to produce modified materials with varying composition (0.0 wt%, 0.02 wt%, 0.05 wt%, 0.07 wt%, 0.10 wt% and 0.15 wt%) of both organic peroxides. Morphological characterisation using modulated differential scanning calorimetry (MDSC) demonstrated that there is a decrease in the crystallinity level for all the modified samples. Shear rheological tests were carried out to study the structure of the modified materials within the linear viscoelastic region. Viscoelastic parameters, such as storage modulus (G'), loss modulus (G
|
404 |
Web crippling of cold-formed stainless steel tubular sectionsZhou, Feng, January 2006 (has links)
Thesis (Ph. D.)--University of Hong Kong, 2006. / Title proper from title frame. Also available in printed format.
|
405 |
Contractile function of single muscle fibers from chronically resistance trained humansShoepe, Todd C. 06 August 2001 (has links)
Resistance training is widely prescribed for rehabilitation of injuries and as a
method to improve athletic performance. It is accepted that resistance training
increases the maximal force production of whole muscle and it has been suggested that
the velocity of shortening can increase as well. However, little is known about the
effects of resistance training at the cellular level. Therefore, we investigated
morphology, force production, velocity, and force-velocity-power relationships of
single chemically skinned muscle fibers from chronically resistance trained humans,
including cross sectional area (CSA), peak Ca²⁺ -activated force production (P₀),
specific tension (P₀/CSA), unloaded shortening velocity (V₀), and isotonic
contractions. The untrained group (NT) group consisted of sedentary males (n=6, age
=27 ± 2 yrs) while the chronically trained group (CHRT) group consisted of males
with 7.7 ± 0.4 yrs resistance training experience (n=6, 22 ± 1 yrs). Maximum
voluntary isometric and isokinetic knee extensor strength were measured along with 6
repetition maximum (6RM) free weight bench press and leg press. Muscle biopsies
were obtained from the vastus lateralis. Chemically skinned single muscle fibers were
mounted between a force transducer and servo-controlled motor and subjected to slack
tests to determine peak Ca²⁺ -activated force (P₀) and unloaded shortening velocity
(V₀). Isotonic load clamps were used to determine the force-velocity-power
relationship. All fiber experiments were performed at 15°C. Fiber myosin heavy
chain (MHC) content was determined by gel electrophoresis. The CHRT group was
119% and 81% stronger for 6RM leg press and bench press respectively. Peak
isometric torque was 28% greater for the CHRT subjects and was significantly higher
at all isokinetic speeds tested. No differences were seen in strength or isokinetic power
between groups after normalization for lean body mass. CHRT fibers (n=213)
expressing type I, IIa, and I₀a/IIx MHC were significantly greater in CSA (+41%,
+51%, and +33%, respectively) and produced significantly greater P₀ (+37%, +48%,
and +34%, respectively) than NT fibers (n=236). However, P₀/CSA was not different
between CHRT and NT groups. Fibers expressing type IIa/IIx fibers produced greater
P₀/CSA than IIa which produced greater P₀/CSA than type I. The P₀/CSA
relationship between fibers within groups was type IIa/IIx>IIa>I and was significant
for both groups. Fiber V₀ was not different between groups. Absolute power was
significantly greater in the CHRT for all fiber types whereas power normalized for
fiber volume was not different between groups. This resulted in a significantly greater
force at peak power for all but type IIa/IIx fibers and trends for greater velocity at
peak power. Single-cell contractile function in terms of V₀ and P₀/CSA, measured
under standardized conditions, appears to be unaltered as a result of long term CHRT
in young adult males. Group differences in absolute P₀ can be attributed solely to the
greater CSA of the CHRT fibers. Long-term CHRT is not associated with a difference
in fiber V₀. Therefore, the greater power was due entirely to the greater force. These
data suggest that differences in whole muscle strength and power between NT and
CHRT groups are primarily due to differences in fiber CSA rather than differences in
cross-bridge mechanisms of contraction. Supported by National Institute of Health
grant R3AR46392A. / Graduation date: 2002
|
406 |
A study of cavitation instabilities in solidsPuttapitukporn, Tumrong 27 February 2003 (has links)
Graduation date: 2003
|
407 |
The effects of training on upper body power in female cross-country skiersDowning, Julie J. 04 June 2002 (has links)
Graduation date: 2003
|
408 |
New strategies to maintain paralyzed skeletal muscle force output during repetitive electrical stimulationChou, Li-Wei. January 2007 (has links)
Thesis (Ph.D.)--University of Delaware, 2006. / Principal faculty advisor: Stuart A. Binder-Macleod, Dept. of Physical Therapy. Includes bibliographical references.
|
409 |
Effect of stimulation train characteristics on the dynamic performance of human skeletal muscleMaladen, Ryan D. January 2006 (has links)
Thesis (M.S.)--University of Delaware, 2006. / Principal faculty advisor: Stuart A. Binder-Macleod, Dept. of Physical Therapy. Includes bibliographical references.
|
410 |
Short-term creatine supplementation does not enhance work capacity in multiple sclerosis individualsMalin, Steven K.. January 2006 (has links)
Thesis (M.S.)--University of Delaware, 2006. / Principal faculty advisor: Cheng-Shun (Richard) Fang, Dept. of Health, Nutrition, and Exercise Sciences. Includes bibliographical references.
|
Page generated in 0.0287 seconds