The understanding of how structural components endure loads, in particular variable loads, is that these components gradually, over some period of time depending on the nature of the loading and the material, develop a microcrack. After some additional time and loading, the microcrack grows to a size that might be detected. Beyond that point, the microcrack propagates in a manner that can be reliably predicted by computer analysis codes. Consequently, one can define different stages for the life of a structural component. These are: 1) the period prior to the formation of a microcrack, 2) the period of microcrack growth, and finally 3) the period of crack growth. To date, structural health monitoring approaches that seek to detect cracks offer no insight into the extent of deterioration occurring in the initial stage that is a precursor to the formation of the microcrack or its growth. However, an approach that would facilitate monitoring the extent of the deterioration that takes place during this stage promises to improve life prediction capabilities of structural components. The challenge, thus, is to develop quantitative assessment of damage accumulation from the earliest stages of the fatigue process and to provide a structure's signature that is dependent of the damage stage. One such signature is the structure's response to forced excitation. The realization of such a goal would help in advancing structural health monitoring procedures using interrogative system identification techniques and determine sensitivities of physical parameters to damage. Additionally, vibration-based spectral quantities are related to physical properties of the structure under test. In this thesis, nonlinear response to parametric excitation is exploited for nonlinear system identification of metallic and composite beam-mass systems before damage initiation through intermediate states of damage progression to failure. Parametric identification procedure combines linear and higher order spectral analysis of vibration measurements and perturbation techniques for the derivation of the approximate solution of the system nonlinear governing differential equation. The possibility of using optical Fiber Bragg Grating sensors technology for damage localization is also assessed. Spectral moments and quantities obtained from fiber optic strain measurements are evaluated near and away from cracks to assess the relation between these moments and cracks. Variations in parameters representing natural frequency, damping and effective nonlinearities for different levels of progressive damage in a beam-mass system have been determined. Their percentage variations have been quantified to establish their sensitivities to damage initiation. The results show that damping and effective nonlinearity parameters are more sensitive to damage conditions than the natural frequency of the first mode. Crack localization is assessed by means of optical fiber technology for a composite beam-mass system. The results show that noise levels in fiber optic signals are high in comparison to strain gage signals. Of particular interest, however, is the observation that the nonlinear response is more pronounced near the cracks than away from them. / Ph. D.

[pt] O aumento dos custos relacionados aos processos de manutenção em estruturas como aeronaves, aliadas à crescente demanda das mesmas, alimentam a necessidade de investimentos em técnicas inovadoras de monitoramento estrutural. Dessa forma, o trabalho realizado nesta tese, busca o desenvolvimento de uma técnica de monitoramento ativo, visando o acompanhamento de parâmetros da estrutura analisada, a fim de identificar e caracterizar processos de dano não visíveis, tais como corrosão e delaminação. A metodologia empregada, teve como base a análise dos padrões de deformação superficial, obtidos com o uso de grades de sensores à fibra óptica baseadas em redes de Bragg (FBG). Inicialmente, tais padrões foram provocados por carregamentos estáticos (tração), e posteriormente por atuadores PTZ fixados à estrutura. Estes últimos são submetidos a uma voltagem alternada e frequência fixa. Esta técnica apresenta todas as vantagens dos sensores FBG (massa e dimensões reduzidas, imunidade eletromagnética, elevado poder de multiplexação e alta sensibilidade entre outras), alem de permitir a visualização de alterações nos padrões de deformação, provocados por danos, através da variação da frequência de excitação. Com relação à interpretação dos resultados, a estratégia empregada consistiu em separar o problema de detecção e caracterização dos danos. Dessa forma, a detecção é realizada comparando a energia das deformações superficiais dos corpos de prova nos casos com e sem defeito, enquanto a caracterização é obtida através a utilização de redes neurais artificiais (RNA), por meio de rotinas de reconhecimento de padrões. / [en] The higher costs related to maintenance processes in structures such as aircraft, coupled with the growing demand of them, fueling the need for investment in innovative techniques for structural monitoring. Thus, the work done in this thesis seeks to develop a technique of active monitoring, aiming at monitoring of structure parameters analyzed in order to identify and characterize processes of hidden damage such as corrosion and delamination. The maid methodology was based on the analysis of patterns of surface deformation, obtained with the use of nets of optical fiber sensors based on fiber Bragg gratings ( FBG ). Initially, these patterns were caused by static loads (tension ), and later by PTZ actuators fixed to the frame, who are subjected to an AC voltage and fixed frequency. This technique has all the advantages of the FBG s sensors (mass and small dimensions, electromagnetic immunity, high multiplexing s power and high sensitivity among others), in addition to allowing visualization of changes in the patterns of deformation caused by damage, by varying the frequency excitation. With respect to the interpretation of the results, the strategy employed was to separate the problem of detection and characterization of damage. Thus, the detection is performed by comparing the deformation energy of the surface of the specimens in the cases with and without defect, whereas the characterization is obtained through the use of artificial neural networks (ANN) by means of pattern recognition routines.

The different topics covered in this thesis include photosensitivity in germanosilicate fibers/glasses and application of fiber Bragg grating sensors in simultaneous strain and temperature discrimination. Fiber Bragg Gratings are wavelength dispersive refractive index structures manufactured through ultra-violet (UV) exposure of optical fibers. Their applications range from wavelength division multiplexing filters, dispersion compensators and fiber laser resonators for telecommunication applications to different types of point or distributive sensors for a variety of applications. One aim of this thesis has been to understand the mechanism of photosensitivity in germanosilicate fibers/preforms. Studies undertaken in this part of the thesis include thermal dynamics of Fiber Bragg Gratings and nano-indentation on ultra-violet irradiated germanosilicate glass preforms. An interesting, periodic appearance of a new peak has been observed in the reflected spectrum of Bragg grating inscribed in a germanosilicate fiber during thermal treatment. The new peak occurs on the longer wavelength side of the spectrum during heating and on the shorter wavelength side during cooling, following an identical reverse dynamics. A commercial grating with 99.9% reflectivity also shows a similar decay dynamics. The observed temperature induced distortion in refractive index modulation profile has been understood in the light of compaction-densification model. It is proposed that during the fabrication process of a grating, the modulation in the thermal expansion coefficient brought about by the interference fringes results in a non-uniform expansion throughout the grating length which in turn results in the distortion of the refractive index profile with increase/decrease in temperature. Since the reflection spectrum of a grating can be approximated as the Fourier transform of the refractive index profile, any distortion in the index profile results in the observed anomalous behaviour in the reflection spectrum. Nano-indentation studies have been performed to measure the changes in mechanical properties of a glass preform subjected to different levels of ultra-violet exposure. The results reveal that short term exposure leads to an appreciable increase in the Young’s modulus suggesting the densification of the glass, confirming the compaction-densification model. However, on prolonged exposure, the Young’s modulus decreases, which provides the first direct evidence of dilation in the glass leading into the Type IIA regime. The present results rule out the hypothesis that continued exposure leads to an irreversible compaction and prove that index modulation regimes are intrinsic to the glass matrix. In the second part of the thesis, three different schemes have been proposed for the use of Fiber Bragg Gratings as strain-temperature discriminating sensors: (a) The first method is based on the measurement of the different characteristic wavelength shifts of two types of gratings. Strain and temperature sensitivities of a Type I Bragg grating (G1) in germania doped silica fiber, fabricated under normal conditions, and zero strain, are compared with that of a Bragg grating inscribed under pre-strained condition (G2). Experimental results show that both, strain and temperature sensitivities of G1 and that of G2 are different. Based on this study, we have proposed an approach which enables simultaneous discrimination of axial strain and temperature. (b) In the second method, a single sensing element has been used to encode strain and temperature into an additional parameter other than the wavelength shift. The thermal out-diffusion of germanium from the core of a photosensitive fiber under elevated temperature is exploited to form a Fabry-Perot filter with a single Fiber Bragg Grating. The filter is fabricated using the standard phase-mask technique and one-time exposure. Energy Dispersive X-Ray analysis is used to measure the out-diffusion. The filter is used as a sensor for simultaneous measurement and discrimination of strain and temperature. The proposed technique, where a single grating is used to discriminate the parameters, provides a large advantage over other existing methods. (c) In the third method, a compact design based on cross-wire arrangement of Fiber Bragg Gratings having identical Bragg resonance and different reflectivity is proposed for simultaneously sensing strain (uniaxial) and temperature. Two gratings are assembled orthogonal to each other on an aluminium base. The cross-wire design allows the two sensors to experience the same temperature but different strain. The gratings are identified by their respective reflectivity and, strain and temperature are resolved from the shift in Bragg wavelength. The proposed design exploits the fact that strain is a vector and temperature is a scalar parameter. This sensor has wide industrial application in discriminating strain from temperature effects.

The electrostatic layer-by-layer (LbL) self-assembly of polyelectrolyte’s has shown applications in thin film coatings, micro patterning, nano-bioreactors and capsules for drug delivery. The film architecture can be precisely designed and controlled to nanometer scale precision with a range from 5 nm to a few microns. Both in vitro and in vivo studies indicate potential applications in biology, pharmaceutics, medicine, and other biomedical areas. This thesis work focused on the design and development of protocols to fabricate polyelectrolyte multi-layer patterns on a variety of substrates such as glass, metals and plastics such as acrylic and polycarbonate. The micro-scale polyelectrolyte patterns have applications in the creation of DNA, protein or cell based microarrays. This work also demonstrated the use of polyelectrolyte multi-layers in the enhancement of fluorescence signals from fluorophore-tagged molecules captured within the multi-layers. In-situ measurements using Fiber Bragg Gratings were carried out to study the kinetics of adsorption and desorption of polyelectrolytes participating in the layer buildup process under different process environmental conditions.

[pt] Este trabalho apresenta um sistema de interrogação de sensores a rede de Bragg em fibras ópticas, baseado em reflectometria no domínio do tempo e filtros fixos a rede de Bragg. Utilizando uma fonte de luz pulsada, a posição espectral do sensor é relacionada à razão da intensidade dos pulsos, tornando a detecção independente de variações de intensidade. São abordados aspectos teóricos e experimentais referentes aos princípios de funcionamento desta técnica. Uma vez que a filtragem é feita com redes de Bragg, apenas um circuito de fotodetecção é utilizado e um número reduzido de acopladores/circuladores ópticos é necessário, o sistema possibilita reduzir consideravelmente o custo para a interrogação de um conjunto de sensores. A utilização de apenas um circuito de fotodetecção apresenta a vantagem de manter as mesmas características para todos os pulsos, minimizando influências externas neste circuito como, por exemplo, variações da temperatura ambiente. Foi montada uma bancada de testes para a interrogação de seis sensores. Comparações entre os resultados experimentais e simulados mostram boa concordância. Extrapolações indicam que seria possível interrogar sensores com uma variação espectral de 2 nanômetros, com incertezas menores que 10 picometros, o que é adequado para sensores de temperatura. Análises de interferência entre dois canais adjacentes mostram pouca influência entre eles e são apresentadas opções para diminuir essa interferência. / [en] This work presents a system for the interrogation of fiber- optic Bragg grating sensors based on time domain reflectometry and Bragg grating fixed filters. Using a pulsed light source, the spectral position of the sensor is related to the ratio of two pulses intensities, making detection independent of intensity variations. Theoretical and experimental aspects regarding the working principles of this technique are discussed. Since filtering is accomplished with Bragg grating so that only one photodetection circuit is used and a reduced number of optic couplers/circulators are needed, the system provides a considerable reduction in the cost of interrogation for a set of sensors. Using only one photodetection circuit also has the advantage of maintaining the same characteristics for all pulses, thus minimizing external influences in this circuit, such as variations in the environment temperature. A test stand was assembled for the interrogation of six sensors. Comparisons between experimental and simulated results show a good agreement. Extrapolations indicate that it would be possible to interrogate sensors with a spectral variation of 2 nanometers, with uncertainties lower than 10 pm, which is adequate for temperature sensors. Cross talk analyses between two adjacent channels show small influence between them, and approaches to reduce this interference are presented.

In this thesis work, a systematic quantitative study has been undertaken, on the performance of etched fiber Bragg Grating (FBG) sensors in the investigation of surface molecular adsorption in real-time; it is shown that the limit of detection (LOD) of FBGs etched below 2 microns diameter, is better compared to prominent optical label-free molecular sensing techniques such as Surface Plasmon Resonance (SPR). Novel fiber optic sensors based on FBG and etched FBG with various nano materials (polyelectrolytes, carbon nanotubes, hydrogel, metals and chalcogenides) coated on the surface of the core or cladding, have been proposed for sensing multi parameters such as pH, protein, humidity, gas, strain, temperature, and light etc. Besides being reproducible and repeatable, the proposed methods are fast, compact, and highly sensitive. A novel optical instrument has also been developed to measure angular deviation, binocular deviation and refractive index of glass slabs, and liquids, based on a shadow casting technique. This method uses the deviation in the geometrical shadow cast by a periodic dot pattern trans-illuminated by a distorted light beam from the transparent test specimen relative to a reference pattern.