Hydraulic circuits with fast dynamic response are often characterized by low power efficiency; on the other hand, energy-efficient circuits under certain circumstances, can demonstrate slow transient responses. Continuously rising energy costs combined with the demand on high performance has necessitated that hydraulic circuits become more efficient yet still demonstrate superior dynamic response. This thesis introduces a new hydraulic circuit configuration which demonstrates high dynamic performance and high efficiency. A pump-controlled hydraulic motor system was used as the basis of the study because of its high circuit efficiency. This is primarily because there is no power loss between the pump and motor. To improve the dynamic response of the pump, a DC motor was designed to control the pump swashplate (and hence flow rate) directly. The pump and DC motor were mathematically modeled and their parameters were experimentally identified. Based on the model and experimental results, a nonlinear PID controller was designed for the DC motor. By means of the DC motors quick dynamic response (in the order of 10 ms), the DC motor controlled pump demonstrated a fast dynamic response with a rise time of 15 to 35 ms depending on the pump pressure. As the dynamic response speed of the pump flow rate was increased, overshoot of the hydraulic motor output also increased. To reduce this overshoot, a bypass flow control circuit was designed to bypass part of the flow during the transient. Due to the unique operating requirements of the bypass flow control system, a PID controller with a resetable integral gain was designed for the valve to reduce the rise time of the bypass control valve. The feasibility ("proof of concept") of the bypass flow control concept was first established using simulation techniques. The simulation results showed that the bypass flow control system could significantly reduced the overshoot of the hydraulic motor rotational speed. The bypass controller was applied to the experimental test circuit. The transient results for the pump-controlled motor system with the bypass flow control are presented under a constant resistive and an inertial load. The test results showed that the bypass flow control could reduce the overshoot of the hydraulic motor rotational speed by about 50%. The relative efficiency of the circuit with the bypass flow control system was 1% to 5% lower for the particular pump-controlled system that was used in this study. For a pump/motor that does not demonstrate significant flow ripple of the magnitude experienced in this study, the relative efficiency would be the same as the pump/motor system without bypass. It was concluded that the proposed bypass control system, combined with the DC motor-swashplate driven pump, could be used to create an energy efficient circuit with excellent dynamic transient responses.

Hydraulic circuits with fast dynamic response are often characterized by low power efficiency; on the other hand, energy-efficient circuits under certain circumstances, can demonstrate slow transient responses. Continuously rising energy costs combined with the demand on high performance has necessitated that hydraulic circuits become more efficient yet still demonstrate superior dynamic response. This thesis introduces a new hydraulic circuit configuration which demonstrates high dynamic performance and high efficiency. A pump-controlled hydraulic motor system was used as the basis of the study because of its high circuit efficiency. This is primarily because there is no power loss between the pump and motor. To improve the dynamic response of the pump, a DC motor was designed to control the pump swashplate (and hence flow rate) directly. The pump and DC motor were mathematically modeled and their parameters were experimentally identified. Based on the model and experimental results, a nonlinear PID controller was designed for the DC motor. By means of the DC motors quick dynamic response (in the order of 10 ms), the DC motor controlled pump demonstrated a fast dynamic response with a rise time of 15 to 35 ms depending on the pump pressure. As the dynamic response speed of the pump flow rate was increased, overshoot of the hydraulic motor output also increased. To reduce this overshoot, a bypass flow control circuit was designed to bypass part of the flow during the transient. Due to the unique operating requirements of the bypass flow control system, a PID controller with a resetable integral gain was designed for the valve to reduce the rise time of the bypass control valve. The feasibility ("proof of concept") of the bypass flow control concept was first established using simulation techniques. The simulation results showed that the bypass flow control system could significantly reduced the overshoot of the hydraulic motor rotational speed. The bypass controller was applied to the experimental test circuit. The transient results for the pump-controlled motor system with the bypass flow control are presented under a constant resistive and an inertial load. The test results showed that the bypass flow control could reduce the overshoot of the hydraulic motor rotational speed by about 50%. The relative efficiency of the circuit with the bypass flow control system was 1% to 5% lower for the particular pump-controlled system that was used in this study. For a pump/motor that does not demonstrate significant flow ripple of the magnitude experienced in this study, the relative efficiency would be the same as the pump/motor system without bypass. It was concluded that the proposed bypass control system, combined with the DC motor-swashplate driven pump, could be used to create an energy efficient circuit with excellent dynamic transient responses.

No description available.

This thesis addresses the H∞ analysis and control of continuous commensurate time-delay systems by frequential methods. First, the asymptotic behavior of the chains of poles are studied, and the conditions of stability for neutral systems with poles approaching the imaginary axis are given. The same analysis is done for fractional systems. In the sequel, a numerical method able to locate all the stability windows as well as the unstable root-locus for classical and fractional system is given. We conclude the analysis part by providing the stability crossing curves of a class of distributed delay system. Starting the synthesis part, we design PID controllers for unstable fractional systems using a small-gain theorem approach. Finally, using the Rekasius substitution, we construct a linear time invariant comparison system that allows us to get information about stability and H∞-norm for classical time-delay systems. Using this approach it is possible to design state and output feedback controllers, as well as linear filters for this class of systems.

Arbetet handlar om hur man med hjälp av LabVIEW 8.0 kan lösa olika uppgifter. Uppgifterna löses med hjälp av ett DAQ-kort. DAQ-kortet gör det möjligt att mata in signaler, som sedan behandlas efter behov i programmet och därefter skickas ut genom DAQ- kortet till olika komponenter som man vill styra. DAQ-kortet klarar att behandla både analoga och digitala signaler. LabVIEW 8.0 och dess historia, DAQ-kortet samt de olika processerna/uppgifter beskrivs mer utförligt i arbetet.

Denna rapport behandlar utveckling av en tvåhjulig balanserande robot. En PID-regulator är implementerad i en mikrokontroller, som även AD-omvandlar en sensorsignal, samt styr motorer via H-bryggor med pulsbreddsmodulering. I rapporten förklaras framtagning av diskret PID-regulator, processorkort, motorkort, val av komponenter och sensor för att mäta robotens vinkel mot ett vertikalplan. Roboten kan balansera stillastående, men behöver kompletteras ytterligare med hjulåterkoppling för att kunna balansera medan den kör. Roboten balanserar med mätdata från en mekanisk golvavkännare (potentiometer). Andra sorters sensorer diskuteras också, t ex accelerometer, gyro och optisk sensor. / This report explain the development of a two wheel balancing robot. A PID-regulator is implemented in a microcontroller, which also AD-converts a sensor signal, and generate pulse width modulated signals to drive H-bridges. It is discussed how to develop a discretisized PID regulator, microcontroller and H-bridge circuit boards, as well as how to chose components and suitable sensors for measuring the robots angle against a vertical plane. The robot is able to balance on its own when standing still, but it need to have feedback from its wheel position if it should be able to maintain balancing when moving. The robot use a mechanical floor feeler (potentiometer). Other sensors are also discussed, e g accelerometer, rate gyro and optical sensor.

This master theses deals with different methods for automatic tuning of the existing controller for external axis. Three methods for automatic tuning have been investigated. Two of these are based on the manuell method used today. The third method is based on optimal placement of the dominant poles. Different sensitivity functions are important for this method. At the end of the thesis, a proposal of a complete tool for automatic tuning is given.

The purpose with this masters thesis was to model the scanner in a system for laser bathymetry. The model was then used to develop a controller for the scanner so a good search pattern was achieved. Two different types of models have been tested, a physical model and a Black Box model of Box Jenkins type. The physical model has been derived from Lagranges equations. Identification experiments have been used to compute the Black Box model and to find the unknown parameters in the physical model. Three different controllers have been tested, a PID controller, a model predictive controller and a controller with feedforward. The controller with feedforward gave the best result. By softening the reference signal and using feedforward a good search pattern was achieved.

This study describes the design and implementation of the pitch and roll autopilots for a fixed wing unmanned vehicle. A Tactical Unmanned Aerial Vehicle (TUAV), which is designed at the Middle East Technical University (METU), is used as a platform. This work combines development of the classical and robust controllers, which are used for the pitch and roll autopilots. One of the important steps in the thesis is development of the non-linear dynamic model of the UAV, which is developed in MATLAB/Simulink environment. Two different strategies of the controller design imply development of the PID and controllers. Simulation results illustrate the performances of the designed controllers. Simulation is performed for the nominal model of the UAV and for the model that includes uncertainties and sensor noises.

Land transportation is the main form of transportation around the world. Since the invention of the car land transportation changed drastically. As the cars took a solid part in human lives with the developments in electronics and robotics unmanned land vehicles are the future of both commercial and military land transportation. Today armies want unmanned land vehicles to provide logistical support to the units near threat zones and commercial firms want them to deliver goods more reliably and with less expense. In this thesis, mainly, a 6DoF dynamical model for a four wheeled land vehicle is developed and an autopilot design is presented using PID techniques. For dynamical modeling of the vehicle internal combustion engines, transmissions, tires, suspensions, aero dynamical drag forces and brakes are studied and the model is tested over some scenarios for evaluating its performance.