Digitized by Kansas Correctional Industries / Department: Civil Engineering.

Calcium sulfoaluminate (CSA) cement was used to cast a prestressed voided deck slab bridge girder. The rapid-set properties of CSA cement allowed the initial concrete strength to reach the required 4300 psi needed in order to cut the prestressing strands 6.5 hours after casting. Prestress losses were monitored long-term using vibrating wire strain gages cast into the concrete at the level of the prestressing strands and the data was compared to the American Association of State Highway and Transportation Officials Load and Resistance Factor Design (AASHTO LRFD) predictions for prestress losses. AASHTO methods for prestress loss calculation were overestimated compared to the vibrating wire strain gage data. Material testing was performed to quantify material properties including compressive strength, tensile strength, static and dynamic elastic modulus, creep, and drying and autogenous shrinkage. The material testing results were compared to AASHTO predictions for creep and shrinkage losses. The bridge girder was tested at midspan and a distance 1.25 times the depth of the beam from the face of the support until failure. Midspan testing consisted of a crack reopening test to solve for the effective prestress in the girder and a test until failure. The crack reopen effective prestress was compared to the AASHTO prediction and AASHTO appeared to be effective in predicting losses based on the crack reopen data. The midspan failure was a shear failure, as accurately predicted by AASHTO. The 1.25d test resulted in a bond failure, which was accurately predicted by the AASHTO bond model for prestressed concrete. Funding for this project was provided by The Mountain Plains Consortium.

One microfiche in pocket / Bibliography: leaves 329-354 / xxiv, 354 leaves : ill ; 30 cm. / Title page, contents and abstract only. The complete thesis in print form is available from the University Library. / Thesis (Ph.D.)--University of Adelaide, 1986

The research presented in this thesis focuses on the accuracy of predicting deflections and cambers in partially prestressed suspended slabs. Precision in predicting this behaviour accurately is complex due to the large number of variables which affect the behaviour of suspended prestressed slabs. This level of complexity is particularly relevant for post tensioned slabs due to the numerous on site construction steps. Many of the variables are hard to determine accurately due to their tendency to be unique for each construction site. Variables such as ambient temperatures, concrete material properties, stressing times, applied loads, loading times, prop movement and humidity are all examples of these properties. Hence, when predicting the behaviour of post tensioned suspended slabs of a multi storey building there always remains a degree of uncertainty. The research presented in this thesis addresses crucial areas of this topic and ultimately aims to supply reinforced concrete designers and constructors with additional confidence when predicting this behaviour. The requirement for this project surfaced during the design stages of 151 Pirie, a multistorey building constructed in Adelaide, Australia. The design project for 151 Pirie was particularly complex due to a very ambitious construction timeline. The strict construction timeline was imposed due to the contractual agreement of early occupancy of the top three floors (of a 9 storey building). The client purchasing the top floors required functioning office space within a matter of months. This contract created a construction priority of erecting the bare structural requirements up to and including the top three floors in the shortest possible time. Fittings and services to the top three floors was then the secondary priority. Fitting and services to the lower floors (which would usually be achieved before the upper floors) would be performed at a later date. Excessive deflection limits of the slabs due to the accelerated construction were a major concern for the client. The effect on the deformation performance due to the accelerated construction was difficult to predict for the designer. Therefore, this project was born to help supply confidence to the designer and concrete supplier for this construction scenario. This research project was designed to assist in the close monitoring and recording of the construction process of 151 Pirie. Due to the nature of data collection, data from this construction site would be limited in its benefits for the current construction. However, the data obtained would be vital for future projects by providing a log of onsite slab performance data as well as explanations of delays or other general outcomes with the construction process. Therefore, the aim of this research is to present the issues that were faced, the methods used to overcome these issues as well as displaying the vast amounts of site specific data documented within this project for future reference. In this research a wide range of concrete material properties were collected and monitored closely on site as well as in the laboratory. The experimental testing created large detailed database of concrete material properties as well as other relevant factors such as surveyed deflections and construction timing. Concrete material properties were the primary focus of this research due to their direct effect on member performance. The database was sufficiently large to allow a meaningful statistical data analysis to be performed on the compressive strength (f’[subscript]c), modulus of elasticity (E[subscript]c) and tensile strength (f’[subscript] t) of the concrete samples. This analysis supplied a detailed understanding of the statistical relationship between different concrete material properties. A Monte Carlo simulation was performed, with multiple deflection and camber models, to create a statistical distribution of predicted deflections and cambers from the statistical distribution of concrete material properties. This statistical output is then critically analysed and compared to the surveyed data. Proposed improvements to the process of predicting deflections and cambers have been outlined. These improvements have then been utilised in the construction of a finite element style program. Finally, the multiple predictions of column strip and mid panel deformation are compared to the short term surveyed deflections. It is summarised that the improvements suggested and implemented in the finite style analysis yield results with a higher degree of accuracy. The accuracy and benefits of the suggested improvements has been justified and proven by the application of multiple examples and a parametric study. / http://proxy.library.adelaide.edu.au/login?url= http://library.adelaide.edu.au/cgi-bin/Pwebrecon.cgi?BBID=1366459 / Thesis (M.Eng.Sc.) -- University of Adelaide, School of Civil, Environmental and Mining Engineering, 2009

This PhD thesis is divided into two parts. Part one dealswith the development of the material and the mechanicalproperties of Steel Fibrous Cement Based Composites (SFCBC) forimproving bridge design and construction. It familiarizes thehydration mechanisms of the high performance concrete with thehelp of Powers´ and Jensen´s models. Concretes withdifferent water-cement ratio were compared with each other withrespect to degree of hydration and hydration products. Thisanalysis showed that high performance concrete has higherstrengths not because it has more gel solid, but due to ithaving less porosity and higher filler content compared toordinary concrete. A number of experiments were performed to achieve a mixdesign method for a SFCBC, which has good workability, highearly and long-term strength and good durabilitycharacteristics. A Self-compacting and self-leveling fibrouscomposite, which has ultra high strengths (Compressive strengthfc= 180 ~ 220MPa and flexural tensile strengthfföi= 14 ~ 32MPa depending on the volumefraction of fibers) was produced. This composite was alsotested under different curing conditions in order toinvestigate the effect of curing on hydration andself-desiccation shrinkage. These tests showed that SFCBCshould not be water-cured under a long period andself-desiccation influences the compressive strengthnegatively. Test of scaling at freezing showed that SFCBC hasvery good durability characteristics. Part two deals with the behavior of SFCBC in the anchoragezones of prestressed bridges. The prismatic composite specimenswere tested for different volume fractions of fibers underdifferent concentrations ratios of strip loading. The resultsof these tests showed that the ultimate strength of the SFCBCspecimens was approximately twice that of ordinary concretewith the same size (fc= 60MPa reinforced with stirrups). Therefore,SFCBC has good possibility to replace the traditional rebars inthe anchorage zones of prestressed bridges. This composite has different behavior than the traditionalconcrete e.g. crack formation, failure criteria, effectivestrength and angle of friction. A vertical crack on thecenterline was occurred while wedge developed under the loadingplate. In contrast to ordinary concrete, the cracks could notreach to the bottom of the blocks. The tests results gave the ideas of that this material actslike metals or plastics in the high fiber content. Thismaterial is neither very brittle as concrete nor very ductileas metals but it is somewhere between them. Upper-bound plasticity solutions were utilized for modelingthe bearing capacity of SFCBC. Predictions of this method aregood enough to estimate the bearing capacity of SFCBC in theanchorage zones of prestressed bridges. <b>Keywords:</b>Process improvement of bridges, Prestressedconcrete, High performance concrete, Ultra high performanceconcrete, Hydration, Cement based composites, Fibers,Self-compacting concrete, Bearing capacity, Anchorage zones,Tests

<p>This PhD thesis is divided into two parts. Part one dealswith the development of the material and the mechanicalproperties of Steel Fibrous Cement Based Composites (SFCBC) forimproving bridge design and construction. It familiarizes thehydration mechanisms of the high performance concrete with thehelp of Powers´ and Jensen´s models. Concretes withdifferent water-cement ratio were compared with each other withrespect to degree of hydration and hydration products. Thisanalysis showed that high performance concrete has higherstrengths not because it has more gel solid, but due to ithaving less porosity and higher filler content compared toordinary concrete.</p><p>A number of experiments were performed to achieve a mixdesign method for a SFCBC, which has good workability, highearly and long-term strength and good durabilitycharacteristics. A Self-compacting and self-leveling fibrouscomposite, which has ultra high strengths (Compressive strength<i>f</i><i>c</i>= 180 ~ 220MPa and flexural tensile strength<i>f</i><i>föi</i>= 14 ~ 32MPa depending on the volumefraction of fibers) was produced. This composite was alsotested under different curing conditions in order toinvestigate the effect of curing on hydration andself-desiccation shrinkage. These tests showed that SFCBCshould not be water-cured under a long period andself-desiccation influences the compressive strengthnegatively. Test of scaling at freezing showed that SFCBC hasvery good durability characteristics.</p><p>Part two deals with the behavior of SFCBC in the anchoragezones of prestressed bridges. The prismatic composite specimenswere tested for different volume fractions of fibers underdifferent concentrations ratios of strip loading. The resultsof these tests showed that the ultimate strength of the SFCBCspecimens was approximately twice that of ordinary concretewith the same size (<i>f</i><i>c</i>= 60MPa reinforced with stirrups). Therefore,SFCBC has good possibility to replace the traditional rebars inthe anchorage zones of prestressed bridges.</p><p>This composite has different behavior than the traditionalconcrete e.g. crack formation, failure criteria, effectivestrength and angle of friction. A vertical crack on thecenterline was occurred while wedge developed under the loadingplate. In contrast to ordinary concrete, the cracks could notreach to the bottom of the blocks.</p><p>The tests results gave the ideas of that this material actslike metals or plastics in the high fiber content. Thismaterial is neither very brittle as concrete nor very ductileas metals but it is somewhere between them.</p><p>Upper-bound plasticity solutions were utilized for modelingthe bearing capacity of SFCBC. Predictions of this method aregood enough to estimate the bearing capacity of SFCBC in theanchorage zones of prestressed bridges.</p><p><b>Keywords:</b>Process improvement of bridges, Prestressedconcrete, High performance concrete, Ultra high performanceconcrete, Hydration, Cement based composites, Fibers,Self-compacting concrete, Bearing capacity, Anchorage zones,Tests</p>

Thesis (M.S. in civil engineering)--Washington State University, August 2008. / Includes bibliographical references (p. 79-80).

Thesis (Ph. D.)--University of Texas at Austin, 2001. / Vita. Includes bibliographical references. Available also from UMI/Dissertation Abstracts International.

Thesis (Ph. D.)--Lehigh University, 2003. / Includes vita. Includes bibliographical references (leaves 364-367).

Thesis (Ph. D.)--West Virginia University, 2001. / Title from document title page. Document formatted into pages; contains xiv, 204 p. : ill. (some col.). Vita. Includes abstract. Includes bibliographical references (p. 190-195).