No description available.

No description available.

No description available.

In early 2020, cracks were discovered on the bridge crossing the Torne River at Autio. This resulted in an investigation being launched to determine the structural state of the bridge. In conjunction with this investigation, monitoring equipment was installed on the bridge, which enabled the collection of measured strain at four critical points on the bridge.  In this thesis the measured strain was used to approximate stresses in the prestressing cables and thereby calculate the effects of fatigue on the bridge. Two different structural standards were used to calculate the results: Eurocode 2, and fib Model Code 2010. Likewise, two different cycle-counting methods were used to calculate the results: the Rainflow-algorithm, and the largest-magnitude approach.  Regardless of structural standard or cycle-counting method, the results indicate that the effects of fatigue are neither an issue for the bridge, currently, nor will it be in the expected lifetime of the bridge.

No description available.

In view of the fact that prestressed concrete is extensively used in bridge construction and that it holds potentialities for eventual use in pavement construction, and that methods must be investigated to utilize an otherwise rejected aggregate which cannot be used for its poor performance under natural weathering, it has become of paramount importance that further efforts be made to evaluate the effect of prestressing on the durability of concrete. The purpose of this thesis was twofold: 1) To study the durability of prestressed concrete made of poor-performing aggregate; 2) To compare the freezing and thawing effects on prestressed concrete with those on ordinary concrete. Two mix designs having different proportions of poor performing aggregate were used in this study. Half the number of specimens were post-tensioned after they had been cured for a period of 13 to 18 days in water, and were then replaced in the curing room for 24 hours, Level of prestress was 600 psi. Before transferring the specimens - both prestressed and non-prestressed - into freezing and thawing apparatus, they were tested for fundamental transverse frequency and initial weight and length measurements were recorded. Thereafter, transverse frequency, weight, length change and temperature change measurements were made periodically. The relative dynamic modules of elasticity and durability factor were then calculated for each specimen. On the basis of the results furnished by these tests, it may be concluded that prestressing improves the durability of concrete made of poor performing aggregate and that the magnitude of improvement in the durability ef concrete tends to diminish with increasing proportion of good performing aggregate. / Master of Science

The research conducted was part of a project sponsored by the Virginia Department of Transportation and the Virginia Transportation Research Council. One PCBT-53 girder was fabricated with lightweight, self-consolidating concrete. An additional composite cast-in-place lightweight concrete deck was added at the Virginia Tech Structures and Material Laboratory. The project had two specific goals. The first was to experimentally determine the shear strength of the bridge girder. The initial tests focused on the web-shear strength of the girder, and the second tests focused on the flexure-shear strength. The theoretical predictions for the web shear strength were all conservative when compared to the experimentally measured failure strength. The theoretical predictions of the flexure-shear strength were typically unconservative because during the flexure-shear test the girder reached the nominal flexural strength, and a failure occurred in the previously damaged region of the beam. Shear strength was also predicted using the design material properties. Results from these calculations suggested that the equation for the steel contribution to shear strength proposed in the NCHRP Simplified Method were unconservative. Further investigation into the results from the web-shear test showed that the maximum nominal shear strength calculated using the AASHTO LRFD Specifications was typically unconservative. Test results from this project suggested that the constant multiplier of 0.25 used in the LRFD equation for Vnmax may be too high. Further research may be needed to accurately quantify an upper limit on the shear strength. Additionally, predictions of the initial web-shear cracking load were conservative when using the AASHTO Standard Specifications and the NCHRP Simplified Method. The initial web-shear crack angle was under-predicted using the AASHTO LRFD Specifications. The second goal was to monitor the change in prestress over time (and hence the prestress loss) occurring in the PCBT-53 girder. Prestress losses were experimentally measured by vibrating wire gages (measured changes in concrete strain) and flexural load testing. Measured prestress losses were compared to a theoretical prediction calculated using the AASHTO Refined Method. The amount of prestress recorded at any given time using vibrating wire gages was greater than predictions from the AASHTO Refined method. The effective prestress measured just prior to deck placement was higher than the theoretical prediction, and the measured effective prestress at the time of testing was also higher than the theoretical effective prestressing force. The effective prestress value calculated using the flexural crack initiation method was significantly lower than the effective prestress values predicted by both the code provisions and the vibrating wire gages; however, the effective prestress value calculated using the flexural crack re-opening method corresponded very well with the effective prestress values predicted by the code provisions and measured by the vibrating wire gages. The discrepancy in the crack initiation effective prestress values may be due to prestress losses occurring between placement of the concrete and transfer of the prestress force. These losses are not taken into account when using current code provisions to estimate prestress losses. Additional research is recommended to determine if these losses occur in bulb-tee girders, and if so, to quantify them. Finally, from test results within the scope of this research project, design of prestressed bulb-tee girders with lightweight, self-consolidating concrete is practical. The current AASHTO LRFD Specifications provided conservative results when predicting the shear strength of the PCBT-53. Additionally, prestress losses in PCBT girders fabricated with lightweight, self-consolidating concrete were less than those predicted using the AASHTO Refined method. / Master of Science

Motivated by Robert Mast's original papers on lifting stability, this research study provides a method for predicting beam behavior during lifting, with application in the construction of bridges. A beam lifting cracking limit state is developed based on analytical equations for calculating the roll angle of the beam, the internal forces and moments, the weak-axis and strong-axis deflections, and the cross-sectional angle of twist. Finite element simulations are performed to investigate the behavior of concrete beams during lifting and to validate the proposed method. Additionally, a statistical characterization of beam imperfections is presented, based on recently conducted field measurements of beam lateral sweep and eccentricity of lift supports. Finally, numerical examples for two typical precast prestressed concrete beam cross-sections are included to demonstrate the proposed method. / Master of Science

As pontes extradorso surgiram na última década do Século XX, principalmente pelo extraordinário desenvolvimento tecnológico do concreto protendido, que possibilitou uma solução simples e econômica para a construção de pontes. A Odawara Blueway Bridge, construída em 1995 no Japão, foi a primeira ponte extradorso do mundo. Depois dessa obra, dezenas de outras pontes foram construídas com esse sistema estrutural, principalmente na Ásia, comprovando sua viabilidade técnica e econômica. Todavia, não se tem conhecimento de algum estudo que mostre em que faixa de extensão de vãos as superestruturas de pontes extradorso são economicamente vantajosas em relação a outros sistemas estruturais. Neste trabalho foi realizada uma investigação visando um estudo comparativo entre as superestruturas de pontes em viga reta de concreto protendido e as pontes extradorso, ambas construídas pelo método dos balanços progressivos. Na investigação realizada verificou-se que as pontes extradorso são economicamente competitivas com a ponte em viga reta de concreto protendido, principalmente na faixa de vãos entre 100 e 200 metros. / The extradosed bridges had appeared in the last decade of XX Century, mainly because the extraordinary technological development of the prestressed concrete made possible a simple and economic solution for the construction of bridges. The Odawara Blueway Bridge, built in 1995 in Japan, was the world\'s first extradosed bridge. After that, dozens of other bridges were built with the same structural type, most in Asia, proving it\'s economic and technique advantages. However, there is no knowledge of any study that show on witch span lengths the extradosed bridges are economically advantageous in comparison with others structural types. This work intended to do this study, comparing the superstructures of conventional prestressed concrete bridges and extradosed bridges, both built with de balanced cantilever method. On this investigation confirms that extradosed bridges are economically competitive with prestressed concrete bridges, mainly with span lengths between 100 and 200 meters.

Ductility is a measure of the ability of a material, section, structural element or structural system to sustain deformations prior to collapse without substantial loss of resistance. The Australian design standard, AS 3600, imposes minimum ductility requirements on structural concrete members to try to prevent premature non-ductile failure and hence to ensure adequate strength and ductile-type collapse with large deflections. The requirements also enable members to resist imposed deformation due to differential settlement, time effects on the concrete and temperature effects, whilst ensuring sufficient carrying capacity and a safe design. Current AS 3600 requirements allow a limited increase or reduction in elastically determined bending moments in critical regions of indeterminate beams, accommodating their ability to redistribute moment from highly stressed regions to other parts of the beam. Design moment redistribution limits and ductility requirements in AS 3600 for bonded partially prestressed beams are a simple extension of the requirements for reinforced members. The possibility of premature non-ductile failure occurring by fracture of the reinforcement or prestressing steel in partially prestressed members has not adequately addressed. The aim of this research is to investigate the overload behaviour and deformation capacity of bonded post-tensioned beams. The current ductility requirements and design moment redistribution limits according to AS 3600 are tested to ensure designs are both safe and economical. A local flexural deformation model based on the discrete cracked block approach is developed to predict the deformation capacity of high moment regions. The model predicts behaviour from an initial uncracked state through progressive crack development into yielding and collapse. Local deformations are considered in the model using non-linear material laws and local slip behaviour between steel and concrete interfaces, with rigorous definition of compatibility in the compression and tension zones. The model overcomes limitations of past discrete cracked block models by ensuring compatibility of deformation, rather than strain compatibility. This improvement allows the modeling of members with multiple layers of tensile reinforcement and variable depth prestressing tendons having separate material and bond properties. An analysis method for simple and indeterminate reinforced and partially prestressed members was developed, based on the proposed deformation model. To account for the effect of shear in regions of high moment and shear present over the interior supports of a continuous beam, a modification to the treatment of local steel deformation in the flexural model, based on the truss analogy, was undertaken. Secondary reactions and moments due to prestress and continuity are also accounted for in the analysis. A comparison of past beam test data and predictions by the analysis shows the cracking pattern and deformation capacity at ultimate of flexural regions in reinforced and partially prestressed members to be predicted with high accuracy. The analysis method accurately predicts local steel behaviour over a cracked region and deformation capacity for a wide range of beams which fail either by fracture of steel or crushing of the concrete. A parametric study is used to investigate the influence of different parameters on the deformation capacity of a typical negative moment region in a continuous beam. The structural system consists of a bonded post-tensioned, partially prestressed band beam. The primary parameters investigated are the member height and span-to-depth ratio; relative quantity of reinforcing and prestressing steel; material properties and bond capacity of the steels; and lastly the compression zone properties. Results show that the effects of the various parameters on the overload behaviour of partially prestressed beams follow the same trends as reinforced beams. A new insight into the local steel behaviour between cracks is attained. The deformation behaviour displays different trends for parametric variations of the local bond capacity, bar diameter and crack spacing, when compared to past analytical predictions from comparable studies. The discrepancy in findings is traced back to the definition of the plastic rotation capacity and the sequencing of the yielding of the steels. Compared to the other local deformation models, the current model does not assume a linear distribution of strain at a crack. The current findings highlight an important difference between predicted behaviours from different deformation compatibility requirements in local deformation models which has not yet been discussed in the literature. The local deformation model evaluates the relationship between maximum steel strain at a crack and average steel deformation over a crack spacing for the entire loading history. The total steel percentage, hardening properties of the steel and concrete strength are shown by the model to have the greatest effect on these steel strain localisation factors. Section analysis, as currently used in design, can be improved with the proposed simplification of the relationships to identify and quantify the effects of steel fracture on deformation capacity and strength. The numerical effort required to simulate the overload behaviour of practical beam designs with multiple reinforcement elements and a prestressing tendon are currently too great to be used in an extensive numerical study. The numerically more efficient smeared block approach is shown to accurately predict the ultimate carrying capacity of prestressed beams failing by crushing of the concrete. Consequently, this method is adopted to study the allowable limits of moment redistribution in the present investigation, Simplified relationships of the steel strain localisation factors evaluated in the parametric study of deformation capacity is used to predict maximum steel strains and premature failure. The limits of moment redistribution in bonded, post-tensioned partially prestressed band beams are explored by comparing the design load and predicted carrying capacity, for different section ductilities and design moment redistribution. In addition, the effects of different concrete strengths, up to 85 MPa, along with as three reinforcing and prestressing steel ductilities are quantified and compared to current Australian and international design requirements. Limitations in the carrying capacity are investigated for different reinforcement and prestress uniform elongation capacities. More than one thousand beam simulations produce results showing that current design moment redistribution and ductility requirements in the Australian design code for concrete structures (AS 3600) are sufficient for normal strength concretes (less than 50 MPa). A suggestion for design moment redistribution limits, section ductility requirements and steel ductility limits is made for members constructed from higher strength concretes. A special high steel ductility class is proposed for both the reinforcement and prestressing steel to allow moment redistribution in higher strength concrete. No moment redistribution is proposed for members reinforced with low ductility (Class L) steel. An increase of the current elongation limit of Class L steel from 1.5 % to 2.5% is suggested to ensure strength and safety. An increase in the current ductility requirements from fsu/ fsy=1.03 and elongation equal to 1.5% to fsu/fsy=1.05 and 2.5% elongation for low ductility Class L steel is suggested to ensure strength and safety. / Thesis (Ph.D.)--Civil and Environmental Engineering, 2004.